CEN ISO/TS 15011-5:2006
(Main)Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 5: Identification of thermal-degradation products generated when welding or cutting through products composed wholly or partly of organic materials (ISO/TS 15011-5:2006)
Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 5: Identification of thermal-degradation products generated when welding or cutting through products composed wholly or partly of organic materials (ISO/TS 15011-5:2006)
ISO/TS 15011-5:2006 specifies procedures for obtaining information about thermal degradation products generated when welding, cutting through, preheating and straightening products composed wholly or partly of organic substances, e.g. shop primers, paints, adhesives, waxes, sealants, pressing lubricant, oils, etc. It is aimed primarily at test laboratories performing such procedures. The data generated may be used by product manufacturers to provide information for inclusion in safety data sheets and by occupational hygienists to identify thermal degradation products of significance in the performance of risk assessments and/or workplace exposure measurements. The data cannot be used to estimate workplace exposure directly.
ISO/TS 15011-5:2006 is applicable to all products composed partly or wholly of organic materials that could be heated, during welding and cutting, to temperatures at which thermal degradation products are generated and where it is not apparent what those degradation products will be.
Arbeits- und Gesundheitsschutz beim Schweißen und bei verwandten Verfahren - Laborverfahren zum Sammeln von Rauch und Gasen - Teil 5: Identifizierung von thermischen Zersetzungsprodukten erzeugt beim Schweißen und Schneiden von ganz oder teilweise aus organischen Materialen bestehenden Produkten (ISO/TS 15011-5:2006)
Diese Vornorm legt Verfahren fest, mit denen Informationen über thermische Zersetzungsprodukte gewonnen werden können, die beim Schweißen, Durchschneiden, Vorheizen und Richten von Produkten entstehen, die ganz oder teilweise aus organischen Stoffen bestehen, z. B. Fertigungsbeschichtungen, Lacke, Klebemittel, Dichtungsmittel, Öle usw. Sie wendet sich in erster Linie an Prüflaboratorien, die diese Prüfungen durchführen. Die gewonnen Daten können von Produktherstellern dazu verwendet werden, Informationen in Sicherheitsdatenblättern zu geben sowie von Arbeitsmedizinern zur Identifizierung von thermischen Zersetzungsprodukten, die für die Durchführung von Risikobewertungen und/oder Arbeitsplatzmessungen von Bedeutung sind. Die Daten können nicht direkt zur Beurteilung von Expositionen verwendet werden.
Diese Vornorm gilt für alle Produkte, die ganz oder teilweise aus organischen Stoffen bestehen und die beim Schweißen und Schneiden auf Temperaturen erhitzt werden könnten, bei denen thermische Zersetzungsprodukte erzeugt werden und bei denen nicht von vornherein erkennbar ist, welche Zersetzungsprodukte entstehen können.
Hygiène et sécurité en soudage et techniques connexes - Méthode de laboratoire d'échantillonnage des fumées et des gaz - Partie 5: Identification des produits de dégradation thermique générés lors du soudage ou du coupage de produits entièrement ou partiellement constitués de matériaux organiques (ISO/TS 15011-5:2006)
Zdravje in varnost pri varjenju in podobnih postopkih - Laboratorijska metoda za vzorčenje dima in plinov, nastalih pri obločnem varjenju - 5. del: Določanje dimov in plinov, ki nastanejo pri varjenju in rezanju izdelkov, ki so v celoti ali delno iz organskih snovi (ISO/TS 15011-5:2006)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2006
=GUDYMHLQYDUQRVWSULYDUMHQMXLQSRGREQLKSRVWRSNLK/DERUDWRULMVNDPHWRGD]D
Y]RUþHQMHGLPDLQSOLQRYQDVWDOLKSULREORþQHPYDUMHQMXGHO 'RORþDQMHGLPRY
LQSOLQRYNLQDVWDQHMRSULYDUMHQMXLQUH]DQMXL]GHONRYNLVRYFHORWLDOLGHOQRL]
RUJDQVNLKVQRYL ,6276
Health and safety in welding and allied processes - Laboratory method for sampling fume
and gases - Part 5: Identification of thermal-degradation products generated when
welding or cutting through products composed wholly or partly of organic materials
(ISO/TS 15011-5:2006)
Arbeits- und Gesundheitsschutz beim Schweißen und bei verwandten Verfahren -
Laborverfahren zum Sammeln von Rauch und Gasen - Teil 5: Identifizierung von
thermischen Zersetzungsprodukten erzeugt beim Schweißen und Schneiden von ganz
oder teilweise aus organischen Materialen bestehenden Produkten (ISO/TS 15011-
5:2006)
Hygiene et sécurité en soudage et techniques connexes - Méthode de laboratoire
d'échantillonnage des fumées et des gaz - Partie 5: Identification des produits de
dégradation thermique générés lors du soudage ou du coupage de produits entierement
ou partiellement constitués de matériaux organiques (ISO/TS 15011-5:2006)
Ta slovenski standard je istoveten z: CEN ISO/TS 15011-5:2006
ICS:
13.100 Varnost pri delu. Industrijska Occupational safety.
higiena Industrial hygiene
25.160.10 Varilni postopki in varjenje Welding processes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
TECHNICAL SPECIFICATION
CEN ISO/TS 15011-5
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
March 2006
ICS 25.160.10; 13.100
English Version
Health and safety in welding and allied processes - Laboratory
method for sampling fume and gases - Part 5: Identification of
thermal-degradation products generated when welding or cutting
through products composed wholly or partly of organic materials
(ISO/TS 15011-5:2006)
Hygiène et sécurité en soudage et techniques connexes - Arbeits- und Gesundheitsschutz beim Schweißen und bei
Méthode de laboratoire d'échantillonnage des fumées et verwandten Verfahren - Laborverfahren zum Sammeln von
des gaz - Partie 5: Identification des produits de Rauch und Gasen - Teil 5: Ermittlung von Rauch und
dégradation thermique générés lors du soudage ou du Gasen hervorgerufen durch Schweißen und Schneiden von
coupage de produits entièrement ou partiellement Erzeugnissen, die ganz oder teilweise aus organischen
constitués de matériaux organiques (ISO/TS 15011-5:2006) Materialien bestehen (ISO/TS 15011-5:2006)
This Technical Specification (CEN/TS) was approved by CEN on 27 September 2005 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN ISO/TS 15011-5:2006: E
worldwide for CEN national Members.
Foreword
This document (CEN ISO/TS 15011-5:2006) has been prepared by Technical Committee
CEN/TC 121 "Welding", the secretariat of which is held by DIN, in collaboration with Technical
Committee ISO/TC 44 "Welding and allied processes".
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to announce this CEN Technical Specification: Austria,
Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United
Kingdom.
TECHNICAL ISO/TS
SPECIFICATION 15011-5
First edition
2006-03-15
Health and safety in welding and allied
processes — Laboratory method for
sampling fume and gases —
Part 5:
Identification of thermal-degradation
products generated when welding or
cutting through products composed
wholly or partly of organic materials
Hygiène et sécurité en soudage et techniques connexes — Méthode de
laboratoire d'échantillonnage des fumées et des gaz —
Partie 5: Identification des produits de dégradation thermique générés
lors du soudage ou du coupage de produits entièrement ou
partiellement constitués de matériaux organiques
Reference number
ISO/TS 15011-5:2006(E)
©
ISO 2006
ISO/TS 15011-5:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2006 – All rights reserved
ISO/TS 15011-5:2006(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 1
4 Principle. 2
5 Procedure . 2
5.1 Screening tests to identify thermal degradation products. 2
5.2 Production of safety data sheet information .2
5.3 Production of user-specific risk assessment data. 3
5.4 Data handling . 3
6 Use and comprehensiveness of data on thermal degradation products. 3
6.1 Use of data on thermal degradation products. 3
6.2 Comprehensiveness of data on thermal degradation products . 3
7 Test report . 3
Annex A (normative) Screening tests to identify thermal degradation products. 5
Annex B (normative) Procedures for determination of thermal degradation products. 7
Annex C (informative) Sampling chambers. 10
Annex D (normative) Sampling and analytical procedures . 13
Annex E (informative) Example of a test report sheet. 15
Annex F (informative) Examples of suitable test conditions for arc welding . 16
Annex G (informative) Use of data on thermal degradation products. 17
Bibliography . 18
ISO/TS 15011-5:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
In other circumstances, particularly when there is an urgent market requirement for such documents, a
technical committee may decide to publish other types of normative document:
⎯ an ISO Publicly Available Specification (ISO/PAS) represents an agreement between technical experts in
an ISO working group and is accepted for publication if it is approved by more than 50 % of the members
of the parent committee casting a vote;
⎯ an ISO Technical Specification (ISO/TS) represents an agreement between the members of a technical
committee and is accepted for publication if it is approved by 2/3 of the members of the committee casting
a vote.
An ISO/PAS or ISO/TS is reviewed after three years in order to decide whether it will be confirmed for a
further three years, revised to become an International Standard, or withdrawn. If the ISO/PAS or ISO/TS is
confirmed, it is reviewed again after a further three years, at which time it must either be transformed into an
International Standard or be withdrawn.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO/TS 15011-5 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 44, Welding and allied processes, in collaboration with Technical Committee ISO/TC 44, Welding
and allied processes, Subcommittee SC 9, Health and safety, in accordance with the Agreement on technical
cooperation between ISO and CEN (Vienna Agreement).
ISO/TS 15011 consists of the following parts, under the general title Health and safety in welding and allied
processes — Laboratory method for sampling fume and gases:
⎯ Part 1: Determination of emission rate and sampling for analysis of particulate fume
⎯ Part 2: Determination of emission rates of gases, except ozone
⎯ Part 3: Determination of ozone concentration using fixed point measurements
⎯ Part 4: Fume data sheets
⎯ Part 5: Identification of thermal-degradation products generated when welding or cutting through products
composed wholly or partly of organic materials [Technical Specification]
iv © ISO 2006 – All rights reserved
ISO/TS 15011-5:2006(E)
Introduction
Welding and cutting activities generate fumes and gases that can be harmful to health and that must be
controlled within limits laid down in regulations. To assess the risks to health arising from such activities it is
necessary to acquire knowledge of the quantity and composition of the fumes and gases emitted.
[1] [2]
ISO 15011-1 and ISO 15011-2 have been promulgated to generate these data when welding with
consumables comprised mainly of metals and other inorganic substances. However, it is now common
practice in the welding industry to weld or cut through a range of prod
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.