Cold rolled low carbon steel flat products for vitreous enamelling - Technical delivery conditions

This European Standard applies to cold rolled non-coated low carbon steel flat products in rolled widths equal to or over 600 mm and in thicknesses equal to or less than 3 mm, delivered in sheet, wide strip, slit wide strip or cut lengths obtained from slit wide strip or sheet.
It does not apply to cold rolled narrow strip (rolling width < 600 mm) nor to cold rolled flat products for which there is a specific standard, in particular the following:
-   cold-rolled low carbon steel flat products for cold forming (EN 10130);
-   cold-rolled non oriented electrical steel sheet and strip delivered in fully processed state (EN 10106);
-   cold rolled electrical non-alloy and alloy steel sheet and strip delivered in the semi-processed state (EN 10341);
-   cold reduced blackplate (EN 10205);
-   steel sheet and strip for welded gas cylinders (EN 10120);
-   cold-rolled uncoated non-alloy mild steel narrow strip for cold forming (EN 10139);
-   cold-rolled structural steels for general purposes;
-   cold-rolled flat products made of high yield strength for cold forming (EN 10268).

Kaltgewalzte Flacherzeugnisse aus weichen Stählen zum Emaillieren - Technische Lieferbedingungen

Die vorliegende Europäische Norm gilt für kaltgewalzte Flacherzeugnisse ohne Überzug in Breiten  600 mm und Dicken  3 mm aus weichen Stählen zum Kaltumformen, die zum Emaillieren geeignet sind und als Blech, Breitband, längsgeteiltes Breitband oder aus längsgeteiltem Breitband oder Blech hergestellten Stäbe geliefert werden.
Diese Europäische Norm gilt nicht für Kaltband (in Walzbreiten  600 mm), ferner nicht für kaltgewalzte Flacherzeugnisse, für die eigene Normen bestehen, insbesondere für folgende Erzeugnisse:
   kaltgewalzte Flacherzeugnisse aus weichen Stählen zum Kaltumformen (EN 10130);
   kaltgewalztes nichtkornorientiertes Elektroblech und -band im schlussgeglühten Zustand (EN 10106);
   kaltgewalztes Elektroblech und -band aus unlegierten und legierten Stählen im nicht schlussgeglühten Zustand (EN 10341);
   kaltgewalztes Feinstblech (EN 10205);
   Stahlblech und -band für geschweißte Gasflaschen (EN 10120);
   Kaltband ohne Überzug aus weichen unlegierten Stählen für Kaltumformung (EN 10139);
   kaltgewalzte Baustähle für allgemeine Anwendung;
   kaltgewalzte Flacherzeugnisse aus Stahl mit hoher Streckgrenze zum Kaltumformen (EN 10268).

Produits plats laminés à froid, en acier doux pour émaillage par vitrification - Conditions techniques de livraison

La présente Norme européenne est applicable aux produits plats laminés à froid, non revêtus, de largeur supérieure ou égale à 600 mm, d’épaisseur inférieur ou égale à 3 mm, en acier doux, pour l’emboutissage ou pliage à froid et destinés à un émaillage par vitrification, livrés en tôles, larges bandes, larges bandes refendues, barres obtenues à partir de larges bandes refendues ou de tôles.
Elle n’est pas applicable aux feuillards (largeur de laminage < 600 mm) laminés à froid ni aux produits plats laminés à froid pour lesquels il existe une norme spécifique, en particulier aux produits suivants :
   Produits plats laminés à froid en acier doux pour emboutissage à froid (EN 10130),
   Tôles magnétiques en acier à grains non orientés laminées à froid et livrées à l’état fini (prEN 10106),
   Bandes et tôles magnétiques laminées à froid en aciers non-allié et en acier allié livrées à l'état semi-fini (EN 10341),
   Fer noir laminé à froid (EN 10205),
   Tôles et bandes pour bouteilles à gaz soudées en acier (prEN 10120),
   Feuillards non revêtus relaminés à froid en aciers doux non alliés, pour formage à froid (prEN 10139),
   Aciers de construction d’usage général laminés à froid,
   Produits plats laminés à froid à haute limite d’élasticité pour formage à froid (EN 10268).

Hladno valjani ploščati izdelki iz maloogljičnih jekel za emajliranje - Tehnični dobavni pogoji

Ta evropski standard se uporablja za hladno valjane neprevlečene ploščate izdelke iz maloogljičnih jekel v valjanih širinah, ki so enake ali večje od 600 mm ter debelinah, enakih ali manjših od 3 mm, dobavljene v ploščah, širokih trakovih, rezanih širokih trakovih ali rezanih dolžinah iz rezanih širokih trakov ali plošč. Ne uporablja se za valjani ozki trak (valjana širina < 600 mm) niti za hladno valjane ploščate izdelke, za katere se uporablja posebni standard, zlasti naslednji: hladno valjani ploščati izdelki iz maloogljičnih jekel za hladno preoblikovanje (EN 10130); hladno valjane neusmerjene električne jeklene plošče in trakovi, dobavljeni popolnoma obdelani (prEN 10106); hladno valjane električne nelegirane jeklene plošče in trakovi, dobavljeni delno obdelani (prEN 10126); hladno valjane električne legirane jeklene plošče in trakovi, dobavljeni delno obdelani (prEN 10165); hladno preoblikovane nepocinkane plošče (EN 10205); jeklene plošče in trakovi za varjene plinske cilindre (prEN 10120 ); vroče valjani ploščati izdelki iz jekel z visoko mejo tečenja za hladno preoblikovanje (prEN 10149); hladno valjani neprevlečeni nelegirani ozki trakovi iz mehkega jekla za hladno preoblikovanje (prEN 10139); hladno valjana konstrukcijska jekla za splošne namene.

General Information

Status
Withdrawn
Publication Date
25-Jun-2013
Withdrawal Date
25-Jul-2023
Current Stage

Relations

Buy Standard

Standard
EN 10209:2013
English language
25 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kaltgewalzte Flacherzeugnisse aus weichen Stählen zum Emaillieren - Technische LieferbedingungenProduits plats laminés à froid, en acier doux pour émaillage par vitrification - Conditions techniques de livraisonCold rolled low carbon steel flat products for vitreous enamelling - Technical delivery conditions77.140.50SROL]GHONLFlat steel products and semi-productsICS:Ta slovenski standard je istoveten z:EN 10209:2013SIST EN 10209:2013en,fr,de01-september-2013SIST EN 10209:2013SLOVENSKI
STANDARDSIST EN 10209:19981DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10209
June 2013 ICS 77.140.50 Supersedes EN 10209:1996English Version
Cold rolled low carbon steel flat products for vitreous enamelling - Technical delivery conditions
Produits plats laminés à froid, en acier doux pour émaillage par vitrification - Conditions techniques de livraison
Kaltgewalzte Flacherzeugnisse aus weichen Stählen zum Emaillieren - Technische Lieferbedingungen This European Standard was approved by CEN on 11 April 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10209:2013: ESIST EN 10209:2013

Foreword .3 1 Scope .4 2 Normative references .4 3 Terms and definitions .5 4 Designation .5 5 Requirements .5 6 Tests .8 7 Identification .9 8 Packaging .9 9 Disputes .9 10 Information to be supplied by the purchaser at the time of ordering .9 Annex A (normative)
Methods for determining the resistance to fish scaling of a steel sheet for enamelling . 13 Annex B (normative)
Method for determining mass loss (iron loss) due to pickling for steel grades for direct enamelling in accordance with 5.4.2 . 17 Annex C (normative)
Method for determining the adherence level of enamel applied to a steel sheet . 20 Annex D (informative)
Characteristics for the selection of enamelling steel grades . 25
1 Scope This European Standard applies to cold rolled non-coated low carbon steel flat products in rolled widths equal to or over 600 mm and in thicknesses equal to or less than 3 mm, delivered in sheet, wide strip, slit wide strip or cut lengths obtained from slit wide strip or sheet. It does not apply to cold rolled narrow strip (rolling width < 600 mm) nor to cold rolled flat products for which there is a specific standard, in particular the following: — cold-rolled low carbon steel flat products for cold forming (EN 10130); — cold-rolled non oriented electrical steel sheet and strip delivered in fully processed state (EN 10106); — cold rolled electrical non-alloy and alloy steel sheet and strip delivered in the semi-processed state (EN 10341); — cold reduced blackplate (EN 10205); — steel sheet and strip for welded gas cylinders (EN 10120); — cold-rolled uncoated non-alloy mild steel narrow strip for cold forming (EN 10139); — cold-rolled structural steels for general purposes; — cold-rolled flat products made of high yield strength for cold forming (EN 10268). 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10021, General technical delivery conditions for steel products EN 10027-1, Designation systems for steels - Part 1: Steel names EN 10027-2, Designation systems for steels - Part 2: Numerical system EN 10049, Measurement of roughness average Ra and peak count RPc on metallic flat products EN 10079:2007, Definition of steel products EN 10131, Cold rolled uncoated and zinc or zinc-nickel electrolytically coated low carbon and high yield strength steel flat products for cold forming - Tolerances on dimensions and shape EN 10204, Metallic products - Types of inspection documents EN ISO 377, Steel and steel products - Location and preparation of samples and test pieces for mechanical testing (ISO 377) EN ISO 6892-1, Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1) ISO 10113, Metallic materials — Sheet and strip — Determination of plastic strain ratio SIST EN 10209:2013

Subject to agreement between the supplier and the purchaser, they may be supplied with particular suitability for the production of a specific part; in this case a maximum rejection percentage may be set by mutual agreement and acceptance on the basis of mechanical properties would not apply. 5.7 Mechanical properties The mechanical properties given in Table 2 only apply to skin-passed products. These mechanical properties are valid for the period specified in Table 2 from the date on which the products are made available. The date of availability shall be notified to the purchaser with reasonable prior notice compatible with the validity of the mechanical properties. SIST EN 10209:2013

Unless otherwise agreed, a single surface of the product shall comply with the specified requirements. The other surface shall be such that during subsequent treatment it does not have a deleterious effect on the better surface. 5.8.3 Surface finish The surface finish may be normal or rough. In the absence of a requirement in the order, products shall be supplied with the normal surface finish. The limiting figures for average surface roughness for the two types of finish are given in Table 1. The measurements shall be made in accordance with EN 10049. If specially agreed at the time of ordering, other ranges for surfaces are specified for specific end uses. Table 1 — Surface finishes and standard roughness Surface finish Symbol Roughness Normal Rough m r 0,6 µm < Ra ≤ 1,9 µm Ra > 1,6 µm 5.9 Stretcher strain marks All the products are generally subjected to a light skin-pass afte
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.