prEN ISO 6506-2

Metallic materials - Brinell hardness test - Part 2: Verification and calibration of testing machines (ISO/DIS 6506-2:2023)

ISO 6506-2:2017 specifies methods of direct and indirect verification of testing machines used for determining Brinell hardness in accordance with ISO 6506‑1 and also specifies when these two types of verification have to be performed.
The direct verification involves checking that individual machine performance parameters fall within specified limits whereas the indirect verification utilizes hardness measurements of reference blocks, calibrated in accordance with ISO 6506‑3, to check the machine's overall performance.
If a testing machine is also to be used for other methods of hardness testing, it has to be verified independently for each method.
ISO 6506-2:2017 is applicable to both fixed location and portable hardness testing machines. For machines that are incapable of satisfying the specified force-time profile, the direct verification of force and testing cycle can be modified by the use of Annex B.

Metallische Werkstoffe - Härteprüfung nach Brinell - Teil 2: Überprüfung und Kalibrierung der Prüfmaschinen (ISO/DIS 6506-2:2023)

Matériaux métalliques - Essai de dureté Brinell - Partie 2: Vérification et étalonnage des machines d'essai (ISO/DIS 6506-2:2023)

L'ISO 6506-2 :2017 spécifie des méthodes de vérifications directe et indirecte des machines d'essai utilisées pour la détermination de la dureté Brinell conformément à l'ISO 6506‑1 et spécifie également quand ces deux types de vérification doivent être réalisées.
La vérification directe implique de contrôler que les paramètres individuels de performance de la machine se situent à l'intérieur des limites spécifiées tandis que la vérification indirecte utilise des mesurages de dureté de blocs de référence, étalonnés conformément à l'ISO 6506‑3 pour contrôler la performance globale de la machine.
Si une machine d'essai est également utilisée pour d'autres méthodes d'essai de dureté, elle doit être vérifiée indépendamment pour chaque méthode.
L'ISO 6506-2 :2017 est applicable aux machines d'essai de dureté d'implantation fixe et portables. Pour les machines ne permettant pas de respecter le profil force-temps spécifié, la vérification directe de la force et du cycle d'essai peut être modifiée en utilisant l'Annexe B.

Kovinski materiali - Preskus trdote po Brinellu - 2. del: Preverjanje in umerjanje naprav za preskušanje (ISO/DIS 6506-2:2023)

General Information

• Status: Not Published
• Publication Date: 18-May-2025
• ICS: 19.060 - Mechanical testing
• ICS: 77.040.10 - Mechanical testing of metals
• Technical Committee: ECISS/TC 101 - Test methods for steel (other than chemical analysis)
• Drafting Committee: ECISS/TC 101 - Test methods for steel (other than chemical analysis)
• Current Stage: 4060 - Closure of enquiry - Enquiry
• Start Date: 15-Jan-2024
• Completion Date: 15-Jan-2024
• Ref Project: oSIST prEN ISO 6506-2:2023 - Metallic materials - Brinell hardness test - Part 2: Verification and calibration of testing machines (ISO/DIS 6506-2:2023)

Relations

• Revises: EN ISO 6506-2:2018 - Metallic materials - Brinell hardness test - Part 2: Verification and calibration of testing machines (ISO 6506-2:2017)
• Effective Date: 20-Oct-2021

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN ISO 6506-2:2023
01-december-2023
Kovinski materiali - Preskus trdote po Brinellu - 2. del: Preverjanje in umerjanje
naprav za preskušanje (ISO/DIS 6506-2:2023)
Metallic materials - Brinell hardness test - Part 2: Verification and calibration of testing
machines (ISO/DIS 6506-2:2023)
Metallische Werkstoffe - Härteprüfung nach Brinell - Teil 2: Überprüfung und Kalibrierung
der Prüfmaschinen (ISO/DIS 6506-2:2023)
Matériaux métalliques - Essai de dureté Brinell - Partie 2: Vérification et étalonnage des
machines d'essai (ISO/DIS 6506-2:2023)
Ta slovenski standard je istoveten z: prEN ISO 6506-2
ICS:
77.040.10 Mehansko preskušanje kovin Mechanical testing of metals
oSIST prEN ISO 6506-2:2023 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 6506-2:2023

---------------------- Page: 2 ----------------------
oSIST prEN ISO 6506-2:2023
DRAFT INTERNATIONAL STANDARD
ISO/DIS 6506-2
ISO/TC 164/SC 3 Secretariat: DIN
Voting begins on: Voting terminates on:
2023-10-23 2024-01-15
Metallic materials — Brinell hardness test —
Part 2:
Verification and calibration of testing machines
Matériaux métalliques — Essai de dureté Brinell —
Partie 2: Vérification et étalonnage des machines d'essai
ICS: 77.040.10
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 6506-2:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023

---------------------- Page: 3 ----------------------
oSIST prEN ISO 6506-2:2023
ISO/DIS 6506-2:2023(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 6506-2
ISO/TC 164/SC 3 Secretariat: DIN
Voting begins on: Voting terminates on:

Metallic materials — Brinell hardness test —
Part 2:
Verification and calibration of testing machines
Matériaux métalliques — Essai de dureté Brinell —
Partie 2: Vérification et étalonnage des machines d'essai
ICS: 77.040.10
This document is circulated as received from the committee secretariat.
COPYRIGHT PROTECTED DOCUMENT
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2023
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: [phone]
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: [e-mail]
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 6506-2:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
  © ISO 2023 – All rights reserved
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023

---------------------- Page: 4 ----------------------
oSIST prEN ISO 6506-2:2023
ISO/DIS 6506-2:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions .
...