EN ISO 11296-4:2018

Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 4: Lining with cured-in-place pipes (ISO 11296-4:2018)

ISO 11296-4:2018, in conjunction with ISO 11296‑1, specifies requirements and test methods for cured-in-place pipes and fittings used for the renovation of underground non-pressure drainage and sewerage networks with service temperatures up to 50 °C.
ISO 11296-4:2018 applies to the use of various thermosetting resin systems, in combination with compatible fibrous carrier materials, reinforcement, and other process-related plastics components (see 5.3).

Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten drucklosen Entwässerungsnetzen (Freispiegelleitungen) - Teil 4: Vor Ort härtendes Schlauch-Lining (ISO 11296-4:2018)

Dieses Dokument legt in Verbindung mit ISO 11296 1 die Anforderungen und Prüfverfahren für vor Ort härtende Schlauch-Lining-Rohre und  Formstücke fest, die für die Renovierung erdverlegter druckloser Entwässerungsnetzwerke (Freispiegelleitungen) mit Betriebstemperaturen bis 50 °C verwendet werden.
Es gilt für die Verwendung verschiedener thermisch aushärtender Harzsysteme (Duroplaste) in Kombination mit kompatiblen faserigen Trägermaterialien, Verstärkungen und anderen zum Verfahren gehörenden Kunststoffelementen (siehe 5.2).

Systèmes de canalisations en plastique pour la rénovation des réseaux de branchements et de collecteurs d'assainissement enterrés sans pression - Partie 4: Tubage continu par tubes polymérisés sur place (ISO 11296-4:2018)

ISO 11296-4:2018, en association avec l'ISO 11296‑1, spécifie les exigences et les méthodes d'essai relatives aux tubes polymérisés sur place et aux raccords utilisés pour la rénovation des réseaux de branchements et de collecteurs d'assainissement enterrés sans pression fonctionnant à des températures de service allant jusqu'à 50 °C.
ISO 11296-4:2018 couvre l'utilisation de divers systèmes de résine thermodurcissable, en combinaison avec des matrices fibreuses compatibles, un renfort et d'autres composants plastiques liés aux procédés (voir 5.3).

Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za odvodnjavanje in kanalizacijo za obratovanje brez tlaka (vodi s prosto gladino) - 4. del: Oblaganje s cevmi, utrjenimi na mestu vgradnje (ISO 11296-4:2018)

Ta dokument skupaj s standardom ISO 11296-1 določa zahteve in preskusne metode za cevi in fitinge, utrjene na mestu vgradnje, ki se uporabljajo za obnavljanje podzemnih omrežij za odvodnjavanje in kanalizacijo, ki obratujejo brez tlaka, s temperaturo med obratovanjem do 50 °C.
Uporablja se za različne sisteme s termično utrjenimi smolami v kombinaciji z združljivimi nosilnimi materiali iz vlaken, deli za ojačitev in drugimi plastičnimi komponentami, povezanimi s procesom (glej 5.3).

General Information

• Status: Published
• Publication Date: 13-Feb-2018
• Withdrawal Date: 30-Aug-2018
• ICS: 23.040.20 - Plastics pipes
• ICS: 23.040.45 - Plastics fittings
• ICS: 91.140.80 - Drainage systems
• ICS: 93.030 - External sewage systems
• Technical Committee: CEN/TC 155 - Plastics piping systems and ducting systems
• Drafting Committee: CEN/TC 155/WG 17 - Plastic components for the use of renovation of piping systems
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 14-Feb-2018
• Completion Date: 14-Feb-2018
• Ref Project: SIST EN ISO 11296-4:2018 - Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 4: Lining with cured-in-place pipes (ISO 11296-4:2018)

Relations

• Replaces: EN ISO 11296-4:2011 - Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 4: Lining with cured-in-place pipes (ISO 11296-4:2009, corrected version 2010-06-01)
• Effective Date: 21-Feb-2018
• Amended By: EN ISO 11296-4:2018/A1:2021 - Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 4: Lining with cured-in-place pipes - Amendment 1: Updated definitions, marking requirements and procedure for alternative expression of flexural test results (ISO 11296-4:2018/Amd 1:2021)
• Effective Date: 11-May-2020

Standards Content (Sample)

SLOVENSKI STANDARD
01-april-2018
1DGRPHãþD
SIST EN ISO 11296-4:2011
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za
odvodnjavanje in kanalizacijo za obratovanje brez tlaka (vodi s prosto gladino) - 4.
del: Oblaganje s cevmi, utrjenimi na mestu vgradnje (ISO 11296-4:2018)
Plastics piping systems for renovation of underground non-pressure drainage and
sewerage networks - Part 4: Lining with cured-in-place pipes (ISO 11296-4:2018)
Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten drucklosen
Entwässerungsnetzen (Freispiegelleitungen) - Teil 4: Vor Ort härtendes Schlauch-Lining
(ISO 11296-4:2018)
Systèmes de canalisations en plastique pour la rénovation des réseaux de
branchements et de collecteurs d'assainissement enterrés sans pression - Partie 4:
Tubage continu par tubes polymérisés sur place (ISO 11296-4:2018)
Ta slovenski standard je istoveten z: EN ISO 11296-4:2018
ICS:
23.040.05 Cevovodi za zunanje Pipeline and its parts for
sisteme za odpadno vodo in external sewage systems
njihovi deli
91.140.80 Drenažni sistemi Drainage systems
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 11296-4
EUROPEAN STANDARD
NORME EUROPÉENNE
February 2018
EUROPÄISCHE NORM
ICS 93.030; 91.140.80; 23.040.20; 23.040.45 Supersedes EN ISO 11296-4:2011
English Version
Plastics piping systems for renovation of underground
non-pressure drainage and sewerage networks - Part 4:
Lining with cured-in-place pipes (ISO 11296-4:2018)
Systèmes de canalisations en plastique pour la Kunststoff-Rohrleitungssysteme für die Renovierung
rénovation des réseaux de branchements et de von erdverlegten drucklosen Entwässerungsnetzen
collecteurs d'assainissement enterrés sans pression - (Freispiegelleitungen) - Teil 4: Vor Ort härtendes
Partie 4: Tubage continu par tubes polymérisés sur Schlauch-Lining (ISO 11296-4:2018)
place (ISO 11296-4:2018)
This European Standard was approved by CEN on 21 January 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11296-4:2018 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 11296-4:2018) has been prepared by Technical Committee ISO/TC 138
“Rehabilitation of pipeline systems” in collaboration with Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2018, and conflicting national standards shall
be withdrawn at the latest by August 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11296-4:2011.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11296-4:2018 has been approved by CEN as EN ISO 11296-4:2018 without any
modification.
INTERNATIONAL ISO
STANDARD 11296-4
Second edition
2018-02
Plastics piping systems for renovation
of underground non-pressure
drainage and sewerage networks —
Part 4:
Lining with cured-in-place pipes
Systèmes de canalisations en plastique pour la rénovation des réseaux
de branchements et de collecteurs d'assainissement enterrés sans
pression —
Partie 4: Tubage continu par tubes polymérisés sur place
Reference number
ISO 11296-4:2018(E)
©
ISO 2018
ISO 11296-4:2018(E)
© ISO 2018, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2018 – All rights reserved

ISO 11296-4:2018(E)
Contents Page
Foreword .v
Introduction .vii
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Symbols and abbreviated terms . 4
4.1 Symbols . 4
4.2 Abbreviated terms . 6
5 Pipes at the “M” stage . 6
5.1 Materials . 6
5.2 General characteristics . 8
5.3 Material characteristics . 8
5.4 Geometric characteristics . 8
5.5 Mechanical characteristics. 8
5.6 Physical characteristics . 8
5.7 Jointing . 9
5.8 Marking . 9
6 Fittings at the “M” stage . 9
6.1 Materials . 9
6.2 General characteristics . 9
6.3 Material characteristics . 9
6.4 Geometric characteristics . 9
6.5 Mechanical characteristics.10
6.6 Physical characteristics .10
6.7 Jointing .10
6.8 Marking .10
7 Ancillary components .11
8 Fitness for purpose of the installed lining system at the “I” stage .11
8.1 Materials .11
8.2 General characteristics .11
8.3 Material characteristics .11
8.4 Geometric characteristics .11
8.4.1 General.11
8.4.2 CIPP wall structure .11
8.4.3 Wall thickness .12
8.5 Mechanical characteristics.12
8.5.1 Reference conditions for testing .12
8.5.2 Test requirements .12
8.6 Physical characteristics .15
8.7 Additional characteristics .
...