prEN ISO 10426-2
(Main)Petroleum and natural gas industries - Cements and materials for well cementing - Part 2: Testing of well cements (ISO/DIS 10426-2:2010)
Petroleum and natural gas industries - Cements and materials for well cementing - Part 2: Testing of well cements (ISO/DIS 10426-2:2010)
Erdöl- und Erdgasindustrie - Zemente und Materialien für die Zementation von Tiefbohrungen - Teil 2: Prüfung von Bohrloch-Zemente (ISO/DIS 10426-2:2010)
Industries du pétrole et du gaz naturel - Ciments et matériaux pour la cimentation des puits - Partie 2: Essais de ciment pour puits (ISO/DIS 10426-2:2010)
Industrija za predelavo nafte in zemeljskega plina - Cementi in materiali za cementiranje vrtin - 2. del: Preskušanje cementov za vrtine (ISO/DIS 10426-2:2019)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2019
Industrija za predelavo nafte in zemeljskega plina - Cementi in materiali za
cementiranje vrtin - 2. del: Preskušanje cementov za vrtine (ISO/DIS 10426-2:2019)
Petroleum and natural gas industries - Cements and materials for well cementing - Part
2: Testing of well cements (ISO/DIS 10426-2:2019)
Erdöl- und Erdgasindustrie - Zemente und Materialien für die Zementation von
Tiefbohrungen - Teil 2: Prüfung von Bohrloch-Zemente (ISO/DIS 10426-2:2019)
Industries du pétrole et du gaz naturel - Ciments et matériaux pour la cimentation des
puits - Partie 2: Essais de ciment pour puits (ISO/DIS 10426-2:2019)
Ta slovenski standard je istoveten z: prEN ISO 10426-2
ICS:
75.180.10 Oprema za raziskovanje, Exploratory, drilling and
vrtanje in odkopavanje extraction equipment
91.100.10 Cement. Mavec. Apno. Malta Cement. Gypsum. Lime.
Mortar
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT INTERNATIONAL STANDARD
ISO/DIS 10426-2
ISO/TC 67/SC 3 Secretariat: SN
Voting begins on: Voting terminates on:
2019-08-09 2019-11-01
Petroleum and natural gas industries — Cements and
materials for well cementing —
Part 2:
Testing of well cements
Industries du pétrole et du gaz naturel — Ciments et matériaux pour la cimentation des puits —
Partie 2: Essais de ciment pour puits
ICS: 91.100.10; 75.020
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 10426-2:2019(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2019
ISO/DIS 10426-2:2019(E)
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
ISO/DIS 10426-2:2019(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
nd
4 Supplements to API RP 10B-2, 2 edition (2013) . 1
4.1 General requirements . 1
4.2 Well-simulation compressive-strength tests . 1
4.3 Non-destructive sonic determination of compressive strength of cement . 2
4.4 Static fluid loss tests . 2
4.5 Determination of rheological properties and gel strength using a rotational viscometer . 2
Bibliography . 3
ISO/DIS 10426-2:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.