EN ISO 11296-3:2011
(Main)Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 3: Lining with close-fit pipes (ISO 11296-3:2009+Cor 1:2011)
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 3: Lining with close-fit pipes (ISO 11296-3:2009+Cor 1:2011)
ISO 11296-3:2009, in conjunction with ISO 11296-1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of non-pressure drainage and sewerage networks.
It applies to pipes and fittings made of polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC‑U). It is applicable to the plastic lining system only.
Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten drucklosen Entwässerungsnetzen (Freispiegelleitungen) - Teil 3: Close-Fit-Lining (ISO 11296-3:2009+Cor 1:2011)
Dieser Teil der ISO 11296 legt in Verbindung mit ISO 11296-1 die Anforderungen und Prüfverfahren für Close-Fit-Lining-Systeme fest, die bei der Renovierung druckloser Entwässerungsnetze (Freispiegelleitungen) verwendet werden.
Er gilt für Rohre und Formstücke, die aus Polyethylen (PE) oder weichmacherfreiem Polyvinylchlorid (PVC-U) hergestellt werden. Sie gilt nur für Kunststoff-Lining-Systeme. Sie legt keine Anforderungen an die be-stehende Rohrleitung fest.
Systèmes de canalisations en plastique pour la rénovation des réseaux de branchements et de collecteurs d'assainissement enterrés sans pression - Partie 3: Tubage par tuyau continu sans espace annulaire (ISO 11296-3:2009+Cor 1:2011)
L'ISO 11296-3:2009, conjointement avec l'ISO 11296-1, spécifie les exigences et les méthodes d'essai pour les systèmes de tubage par tuyau continu sans espace annulaire, destinés à être utilisés pour la rénovation des réseaux d'assainissement enterrés sans pression.
Elle s'applique aux tuyaux et aux raccords en polyéthylène (PE) ou en poly(chlorure de vinyle) non plastifié (PVC‑U). Elle s'applique uniquement au système de rénovation en plastique.
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za odvodnjavanje in kanalizacijo za obratovanje brez tlaka (vodi s prosto gladino) - 3. del: Oblaganje s tesno prilagodljivimi cevmi (ISO 11296-3:2009+Cor 1:2011)
Ta del ISO 11296 v povezavi z ISO 11296-1 določa zahteve in preskusne metode za tesno prilagodljive sisteme za oblaganje, namenjene uporabi za obnovo omrežij za odvodnjavanje in kanalizacijo za obratovanje brez tlaka.
Velja za cevi in fitinge iz polietilena (PE) ali nemehčanega polivinilklorida (PVC-U). Velja samo za polimerni sistem oblaganja. Ne velja za zahteve za obstoječe cevovode.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2011
1DGRPHãþD
SIST EN 13566-3:2003
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za
odvodnjavanje in kanalizacijo za obratovanje brez tlaka (vodi s prosto gladino) - 3.
del: Oblaganje s tesno prilagodljivimi cevmi (ISO 11296-3:2009+Cor 1:2011)
Plastics piping systems for renovation of underground non-pressure drainage and
sewerage networks - Part 3: Lining with close-fit pipes (ISO 11296-3:2009+Cor 1:2011)
Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten drucklosen
Entwässerungsnetzen (Freispiegelleitungen) - Teil 3: Close-Fit-Lining (ISO 11296-
3:2009+Cor 1:2011)
Systèmes de canalisations en matières plastiques pour la rénovation des réseaux
d'assainissement gravitaires enterrés - Partie 3: Tubage par tuyau continu sans espace
annulaire (ISO 11296-3:2009+Cor 1:2011)
Ta slovenski standard je istoveten z: EN ISO 11296-3:2011
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 11296-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2011
ICS 23.040.20; 23.040.45; 93.030; 91.140.80 Supersedes EN 13566-3:2002
English Version
Plastics piping systems for renovation of underground non-
pressure drainage and sewerage networks - Part 3: Lining with
close-fit pipes (ISO 11296-3:2009/Cor 1:2011)
Systèmes de canalisations en plastique pour la rénovation Kunststoff-Rohrleitungssysteme für die Renovierung von
des réseaux d'assainissement enterrés sans pression - erdverlegten drucklosen Entwässerungsnetzen
Partie 3: Tubage par tuyau continu sans espace annulaire (Freispiegelleitungen) - Teil 3: Close-Fit-Lining (ISO 11296-
(ISO 11296-3:2009/Cor 1:2011) 3:2009/Cor 1:2011)
This European Standard was approved by CEN on 8 April 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11296-3:2011: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
The text of ISO 11296-3:2009/Cor 1:2011 has been prepared by Technical Committee ISO/TC 138 “Plastics
pipes, fittings and valves for the transport of fluids” of the International Organization for Standardization (ISO)
and has been taken over as EN ISO 11296-3:2011 by Technical Committee CEN/TC 155 “Plastics piping
systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by November 2011, and conflicting national standards shall be withdrawn
at the latest by November 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13566-3:2002.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 11296-3:2009/Cor 1:2011 has been approved by CEN as a EN ISO 11296-3:2011 without any
modification.
INTERNATIONAL ISO
STANDARD 11296-3
First edition
2009-11-01
Plastics piping systems for renovation
of underground non-pressure drainage
and sewerage networks —
Part 3:
Lining with close-fit pipes
Systèmes de canalisations en matières plastiques pour la rénovation
des réseaux d'assainissement gravitaires enterrés —
Partie 3: Tubage par tuyau continu sans espace annulaire
Reference number
ISO 11296-3:2009(E)
©
ISO 2009
ISO 11296-3:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2009 – All rights reserved
ISO 11296-3:2009(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.1
3 Terms and definitions .2
4 Symbols and abbreviated terms .2
5 Pipes at the “M” stage .2
5.1 Materials .2
5.2 General characteristics.3
5.3 Material characteristics.3
5.4 Geometric characteristics .4
5.5 Mechanical characteristics.4
5.6 Physical characteristics.4
5.7 Jointing.5
5.8 Marking.5
6 Fittings.5
7 Ancillary components.5
8 Fitness for purpose of the installed lining system at the “I” stage .6
8.1 Materials .6
8.2 General characteristics.6
8.3 Material characteristics.6
8.4 Geometric characteristics .6
8.5 Mechanical characteristics.8
8.6 Physical characteristics.8
8.7 Additional characteristics.8
8.8 Sampling.8
9 Installation practice.9
9.1 Preparatory work .9
9.2 Storage, handling and transport of pipes and fittings .9
9.3 Equipment .9
9.4 Installation.10
9.5 Process-related inspection and testing .10
9.6 Lining termination .11
9.7 Reconnection to existing manholes and laterals.11
9.8 Final inspection and testing.11
Annex A (normative) Factory folded heat reverted polyethylene (PE) pipe — Determination of
memory ability .12
Annex B (normative) Folded polyethylene (PE) pipe — Determination of resistance to
circumferential tensile stress at constant temperature .14
Bibliography.19
ISO 11296-3:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of thi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.