EN 13566-3:2002
(Main)Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 3: Lining with close-fit pipes
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 3: Lining with close-fit pipes
This Part 3 of prEN (155wi209), read in conjunction with Part 1, specifies requirements and test methods for pipes and fittings which are part of plastics piping systems installed as close-fit pipes in the renovation of non-pressure drainage and sewerage networks. It covers components made of polyethylene (PE) or unplasticized polyvinyl chloride (PVC-U). It is applicable to the plastic lining system only. It does not cover the requirements for the existing pipeline.
Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten drucklosen Entwässerungsnetzen (Freispiegelleitungen) - Teil 3: Close-Fit-Lining
Dieser Teil 3 der prEN 13566 legt in Verbindung mit prEN 13566-1 die Anforderungen und Prüfverfahren Close-Fit-Lining-Systeme, die bei der Renovierung druckloser Entwässerungsnetze (Freispiegelleitungen) eingebaut werden, fest.
Diese Norm beinhaltet Rohre und Formstücke, die aus Polyethylen (PE) oder weichmacherfreiem Polyvinylchlorid (PVC-U) hergestellt werden. Sie gilt nur auf Kunststoff-Liningsysteme. Sie legt keine Anforderungen an die bestehende Rohrleitung fest.
Systèmes de canalisations plastiques pour la rénovation des réseaux d'assainssement enterrés sans pression - Partie 3: Tubage par tuyau continu sans espace annulaire
La présente partie 3 de l'EN 13566, à consulter en association avec l'EN 13566-1:2002, spécifie les prescriptions et les méthodes d'essai pour les systèmes de tubages par tuyau continu sans espace annulaire utilisés pour la rénovation des réseaux d'assainissement enterrés sans pression.
Elle couvre les tubes et raccords en polyéthylène (PE) ou en poly(chlorure de vinyle) non plastifié (PVC-U).
Elle s'applique uniquement au système de tubage par tuyau plastique. Elle ne couvre pas les exigences de la canalisation existante.
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za odvodnjavanje in kanalizacijo - Obratovanje brez tlaka (vodi s prosto gladino) – 3. del: Oblaganje s tesno prilagodljivimi cevmi
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Cevni sistemi iz polimernih materialov za obnovo podzemnih
omrežij za odvodnjavanje
in kanalizacijo -
Obratovanje brez tlaka (vodi s prosto gladino) – 3. del: Oblaganje s tesno prilagodljivimi cevmiKunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten drucklosen Entwässerungsnetzen (Freispiegelleitungen) - Teil 3: Close-Fit-LiningSystemes de canalisations plastiques pour la rénovation des réseaux d'assainssement enterrés sans pression - Partie 3: Tubage par tuyau continu sans espace annulairePlastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 3: Lining with close-fit pipes93.030Zunanji sistemi za odpadno vodoExternal sewage systems23.040.20Cevi iz polimernih materialovPlastics pipesICS:Ta slovenski standard je istoveten z:EN 13566-3:2002SIST EN 13566-3:2003en01-oktober-2003SIST EN 13566-3:2003SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13566-3December 2002ICS 93.030English versionPlastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 3: Lining withclose-fit pipesRénovation des réseaux d'assainissement gravitairesenterrés par canalisations plastiques - Partie 3: Tubage partuyau continu sans espace annulaireKunststoff-Rohrleitungssysteme für die Renovierung vonerdverlegten drucklosen Entwässerungsnetzen(Freispiegelleitungen) - Teil 3: Close-Fit-LiningThis European Standard was approved by CEN on 4 November 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13566-3:2002 ESIST EN 13566-3:2003
Recommended scheme for assessment of conformity.15A.1Scope.15A.2General.15A.3Testing and Inspection.15SIST EN 13566-3:2003
Folded polyethylene (PE) pipe — Determination of resistance to circumferentialtensile stress at constant temperature.21B.1Scope.21B.2Principle.21B.3Apparatus.21B.4Preparation of test pieces.22B.5Conditioning of test pieces.24B.6Procedure.24B.7Test report.25Bibliography.26SIST EN 13566-3:2003
This is in additionto specifying requirements for system components as manufactured.The system standard EN 13566 comprise six parts, as follows:— Part 1:General— Part 2:Lining with continuous pipes— Part 3:Lining with close-fit pipes (this standard)— Part 4:Lining with cured-in-place pipes— Part 5:Lining with discrete pipes— Part 7:Lining with spirally-wound pipesThe requirements for any given renovation technique family are covered by Part 1: General, applied in conjunctionwith the relevant other Part. For example, for the requirements relating to Lining with close-fit pipes, it is necessaryto refer to both Parts 1 and 3. Complementary information is contained in ISO/TR 11295 [1] and a supportingstandard, EN 13689 [2], listed in the bibliography.A consistent structure of clause headings has been adopted for all parts to facilitate direct comparisons acrossrenovation technique families.Figure 1 shows the common Part and clause structure and the relationship between EN 13566 and the systemstandards for other applications.Annex A of this document is informative. Annex B is normative.This document includes a bibliography.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard : Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain,Sweden, Switzerland and the United Kingdom.SIST EN 13566-3:2003
Plastics piping and ducting systems — Thermoplastics pipes and fittings — Determination of Vicatsoftening temperature (VST).EN 1401-1,
Plastics piping systems for non-pressure underground drainage and sewerage — Unplasticizedpoly(vinyl chloride) (PVC-U) — Part 1:
Specifications for pipes, fi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.