EN ISO 14526-2:1999
(Main)Plastics - Phenolic powder moulding compounds (PF-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14526-2:1999)
Plastics - Phenolic powder moulding compounds (PF-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14526-2:1999)
This part of ISO 14526 specifies the methods of preparation of test specimens and the test methods to be used in
determining the properties of phenolic powder moulding compounds (PF-PMCs). Requirements for handling test
material and for conditioning both the test material before moulding and the specimens before testing are given
here.
Procedures and conditions for the preparation of test specimens and procedures for measuring properties of the
materials from which these specimens are made are given. Properties and test methods which are suitable and
necessary to characterize PMCs are listed.
The properties have been selected from the general test methods in ISO 10350-1. Other test methods in wide use
for, or of particular significance to, PMCs are also included in this part of ISO 14526, as are the designatory
properties found in ISO 14526-1.
In order to obtain reproducible and comparable test results, it is necessary to use the methods of preparation and
conditioning, the specimen dimensions and the test procedures specified herein. Values determined will not
necessarily be identical to those obtained using specimens of different dimensions or prepared using different
procedures.
Plastiques - Poudres à mouler phénoliques (PF-PMC) - Partie 2: Préparation des éprouvettes et détermination des propriétés (ISO 14526-2:1999)
La présente partie de l'ISO 14526 spécifie les méthodes de préparation des éprouvettes et les méthodes d'essai à
appliquer pour déterminer les propriétés des poudres à mouler (PMC). Elle fixe les exigences concernant, d'une
part, le traitement du matériau pour essai, et d'autre part, le conditionnement du matériau pour essai avant
moulage et des éprouvettes avant les essais.
Elle précise les modes opératoires et les conditions à appliquer pour la préparation des éprouvettes et pour le
mesurage des propriétés des matériaux à partir desquels sont fabriquées les éprouvettes. Elle fournit une liste des
propriétés et des méthodes d'essai appropriées et nécessaires à la caractérisation des PMC.
Ces propriétés ont été choisies parmi les méthodes d'essai générales de l'ISO 10350-1. D'autres méthodes d'essai
largement utilisées avec les PMC, ou présentant une importance particulière, sont également incluses dans la
présente partie de l'ISO 14526, tout comme les propriétés de désignation données dans l'ISO 14526-1.
Pour obtenir des résultats reproductibles et comparables, il est nécessaire d'utiliser les méthodes de préparation et
de conditionnement, les dimensions d'éprouvettes et les modes opératoires d'essai spécifiés dans le présent
document. Les valeurs déterminées ne seront pas nécessairement identiques à celles obtenues en utilisant des
éprouvettes de dimensions différentes ou préparées selon d'autres modes opératoires.
Polimerni materiali - Fenolne praškaste zmesi za oblikovanje (PF-PMCs) - 2. del: Priprava preskušancev in ugotavljanje lastnosti (ISO 14526-2:1999)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 14526-2:2000
01-december-2000
Polimerni materiali - Fenolne praškaste zmesi za oblikovanje (PF-PMCs) - 2. del:
Priprava preskušancev in ugotavljanje lastnosti (ISO 14526-2:1999)
Plastics - Phenolic powder moulding compounds (PF-PMCs) - Part 2: Preparation of test
specimens and determination of properties (ISO 14526-2:1999)
Plastiques - Poudres a mouler phénoliques (PF-PMC) - Partie 2: Préparation des
éprouvettes et détermination des propriétés (ISO 14526-2:1999)
Ta slovenski standard je istoveten z: EN ISO 14526-2:1999
ICS:
83.080.10 Duromeri Thermosetting materials
SIST EN ISO 14526-2:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 14526-2:2000
---------------------- Page: 2 ----------------------
SIST EN ISO 14526-2:2000
---------------------- Page: 3 ----------------------
SIST EN ISO 14526-2:2000
---------------------- Page: 4 ----------------------
SIST EN ISO 14526-2:2000
---------------------- Page: 5 ----------------------
SIST EN ISO 14526-2:2000
---------------------- Page: 6 ----------------------
SIST EN ISO 14526-2:2000
INTERNATIONAL ISO
STANDARD 14526-2
First edition
1999-11-15
Plastics — Phenolic powder moulding
compounds (PF-PMCs) —
Part 2:
Preparation of test specimens and
determination of properties
Plastiques — Poudres à mouler phénoliques (PF-PMC) —
Partie 2: Préparation des éprouvettes et détermination des propriétés
Reference number
ISO 14526-2:1999(E)
�
©
ISO 1999
---------------------- Page: 7 ----------------------
SIST EN ISO 14526-2:2000
ISO 14526-2:1999(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 1999
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 734 10 79
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 1999 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 14526-2:2000
ISO 14526-2:1999(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 14526 may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 14526-2 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee
SC 12, Thermosetting materials.
After a transition period of, at the most, four years, the three parts of ISO 14526 (see below) will replace
ISO 800:1992, of which they constitute a technical revision.
ISO 14526 consists of the following parts, under the general title Plastics — Phenolic powder moulding compounds
(PF-PMCs):
� Part 1: Designation system and basis for specifications
� Part 2: Preparation of test specimens and determination of properties
� Part
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.