EN ISO 12224-1:2024
(Main)Solder wire, solid and flux-cored - Specification and test methods - Part 1: Classification and performance requirements (ISO 12224-1:2024)
Solder wire, solid and flux-cored - Specification and test methods - Part 1: Classification and performance requirements (ISO 12224-1:2024)
This document specifies a coding system for the classification and designation of solid and flux-cored solder wire, and the performance requirements to be met by flux-cored wire and its constituents. Requirements for sampling, labelling and packaging are also specified.
Massive Lotdrähte und flussmittelgefüllte Röhrenlote - Festlegungen und Prüfverfahren - Teil 1: Einteilung und Anforderungen (ISO 12224-1:2024)
Dieses Dokument legt ein Kodierungssystem zur Einteilung und Bestimmung massiver Lotdrähte und flussmittelgefüllter Röhrenlote fest sowie die Eignungsanforderungen, die von flussmittelgefülltem Röhrenlot und seinen Bestandteilen zu erfüllen sind. Anforderungen an die Probenahme, Beschriftung und Verpackung werden ebenso festgelegt.
Fils d'apport de brasage tendre, pleins et à flux incorporé - Spécifications et méthodes d'essai - Partie 1: Classification et exigences de performance (ISO 12224-1:2024)
Le présent documentspécifie un système de codification pour la classification et la désignation des fils d'apport de brasage tendre pleins et à flux incorporé destinés, ainsi que les exigences de performance à satisfaire pour les fils à flux incorporé et leurs constituants. Des exigences relatives à l’échantillonnage, à l’étiquetage et à l’emballage sont également spécifiées.
Mehke spajke v obliki žice, palice in strženske žice - Popisi in preskusne metode - 1. del: Razvrstitev in zahteve za lastnosti (ISO 12224-1:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2024
Nadomešča:
SIST EN ISO 12224-1:2001
Mehke spajke v obliki žice, palice in strženske žice - Popisi in preskusne metode -
1. del: Razvrstitev in zahteve za lastnosti (ISO 12224-1:2024)
Solder wire, solid and flux-cored - Specification and test methods - Part 1: Classification
and performance requirements (ISO 12224-1:2024)
Massive Lotdrähte und flussmittelgefüllte Röhrenlote - Festlegungen und Prüfverfahren -
Teil 1: Einteilung und Anforderungen (ISO 12224-1:2024)
Fils d'apport de brasage tendre, pleins et à flux incorporé - Spécifications et méthodes
d'essai - Partie 1: Classification et exigences de performance (ISO 12224-1:2024)
Ta slovenski standard je istoveten z: EN ISO 12224-1:2024
ICS:
25.160.50 Trdo in mehko lotanje Brazing and soldering
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 12224-1
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2024
EUROPÄISCHE NORM
ICS 25.160.50 Supersedes EN ISO 12224-1:1998
English Version
Solder wire, solid and flux-cored - Specification and test
methods - Part 1: Classification and performance
requirements (ISO 12224-1:2024)
Fils d'apport de brasage tendre, pleins et à flux Massive Lotdrähte und flussmittelgefüllte Röhrenlote -
incorporé - Spécifications et méthodes d'essai - Partie Festlegungen und Prüfverfahren - Teil 1: Einteilung
1: Classification et exigences de performance (ISO und Anforderungen (ISO 12224-1:2024)
12224-1:2024)
This European Standard was approved by CEN on 2 December 2023.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 12224-1:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 12224-1:2024) has been prepared by Technical Committee ISO/TC 44 "Welding
and allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2024, and conflicting national standards
shall be withdrawn at the latest by November 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 12224-1:1998.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 12224-1:2024 has been approved by CEN as EN ISO 12224-1:2024 without any
modification.
International
Standard
ISO 12224-1
Second edition
Solder wire, solid and flux-cored —
2024-05
Specification and test methods —
Part 1:
Classification and performance
requirements
Fils d'apport de brasage tendre, pleins et à flux incorporé —
Spécifications et méthodes d'essai —
Partie 1: Classification et exigences de performance
Reference number
ISO 12224-1:2024(en) © ISO 2024
ISO 12224-1:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 12224-1:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification and designation . 1
4.1 Solder alloy designation .1
4.2 Flux classification .2
4.3 Designation of flux-cored solder wire .2
5 Requirements . 2
5.1 Solder alloy composition of solid and flux-cored solder wire .2
5.2 Flux composition of flux-cored solder wire .2
5.3 Flux content .2
5.4 Dimensions and tolerances . . .3
5.5 Copper corrosion test .3
5.6 Influence of flux vapours on insulation resistance (applicable only to flux-cored solder
wires containing type 1 and type 22 fluxes) .4
6 Sampling . 4
6.1 Sampling for chemical analysis of the solder .4
6.2 Sampling for tests to determine the properties of the flux core (i.e. tests as described
in the ISO 9455 series) .4
6.3 Sampling for tests to determine the flux content and the diameter of the flux-cored
solder wire.4
7 Marking, labelling and packaging . 4
Annex A (normative) Method for the solvent extraction of the flux from flux-cored solder wire . 6
Annex B (normative) Measurement of mean diameter of wire . 9
Annex C (informative) Guidance on the use of test methods .10
Bibliography .11
iii
ISO 12224-1:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee
SC 12, Soldering materials, in collaboration with the European Committee for Standardization (CEN)
Technical Committee CEN/TC 121, Welding and allied processes, in accordance with the Agreement on
technical cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 12224-1:1997), which has been technically
revised.
The main changes are as follows:
— Table 1: greater nominal contents added;
— former 5.5 and Table 3 deleted because the spread test is not commonly used;
— former 5.6.1 deleted because the test method was withdrawn;
— 6.1: reference to ISO 10564, which has been withdrawn, replaced by a recommended method;
— in Table A.1 the column for method D was deleted;
— in Table C.1 withdrawn standards were deleted and flux type
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.