EN ISO 6806:2014

Rubber hoses and hose assemblies for use in oil burners - Specification (ISO 6806:2014)

ISO 6806:2014 specifies the minimum requirements for rubber hoses and hose assemblies for use in oil burners.
The following two types of hose assembly are specified.
Type 1: Hose assemblies for flux and reflux, but not for insertion between the oil burner pump and the atomizing connection; maximum working pressure 1,0 MPa (10 bar); maximum oil temperature 100 °C.
Type 2: Hose assemblies for insertion between the oil burner pump and the atomizing connection; working pressure 4,0 MPa (40 bar); maximum oil temperature 100 °C.

Gummischläuche und Schlauchleitungen für den Einsatz in Ölbrennern - Anforderung (ISO 6806:2014)

Tuyaux et fexibles en caoutchouc pour brûleurs - Spécifications (ISO 6806:2014)

L'ISO 6806:2014 spécifie les exigences minimales pour les tuyaux et les flexibles en caoutchouc utilisés pour les brûleurs à fuel.
Les deux types suivants de flexibles sont spécifiés.
- Type 1: flexibles pour le flux et le reflux, mais pas pour l'installation entre la pompe du brûleur et le système de pulvérisation; pression maximale de service 1,0 MPa (10 bar); température maximale du fuel 100 °C.
- Type 2: flexibles pour installation entre la pompe du brûleur et le système de pulvérisation; pression maximale de service 4,0 MPa (40 bar); température maximale du fuel 100 °C.

Gumene cevi in cevni priključki za oljne gorilnike - Specifikacija (ISO 6806:2014)

Ta mednarodni standard določa minimalne zahteve za gumene cevi in cevne priključke
za oljne gorilnike.
Določena sta naslednja tipa cevnih priključkov.
– Tip 1: Cevni priključki za pretok in povratni pretok, a ne za vstavitev med črpalko oljnega gorilnika in
priključek za razprševanje; najvišji delovni tlak 1,0 MPa (10 bar); najvišja temperatura olja
100 °C.
– Tip 2: Cevni priključki za vstavitev med črpalko oljnega gorilnika in priključek za razprševanje;
delovni tlak 4,0 MPa (40 bar); najvišja temperatura olja 100 °C.
OPOMBA: Cevni priključki iz tega mednarodnega standarda niso namenjeni uporabi (brez
posebne ocene) za namene, ki niso inštalacije oljnih gorilnikov.

General Information

• Status: Withdrawn
• Publication Date: 23-Sep-2014
• Withdrawal Date: 20-Jun-2017
• ICS: 23.040.70 - Hoses and hose assemblies
• ICS: 27.060.10 - Liquid and solid fuel burners
• ICS: 83.140.40 - Hoses
• Technical Committee: CEN/TC 218 - Rubber and plastics hoses and hose assemblies
• Drafting Committee: CEN/TC 218/WG 1 - Rubber and plastics hoses and hose assemblies for industrial, chemical and petrochemical applications
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 21-Jun-2017
• Ref Project: SIST EN ISO 6806:2014 - Rubber hoses and hose assemblies for use in oil burners - Specification (ISO 6806:2014)

Relations

• Replaces: EN ISO 6806:1995 - Rubber hoses and hose assemblies for use in oil burners - Specification (ISO 6806:1992)
• Effective Date: 01-Oct-2014
• Replaced By: EN ISO 6806:2017 - Rubber hoses and hose assemblies for use in oil burners - Specification (ISO 6806:2017)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 6806:2014
01-december-2014
1DGRPHãþD
SIST EN ISO 6806:2000
*XPHQHFHYLLQFHYQLSULNOMXþNL]DROMQHJRULOQLNH6SHFLILNDFLMD,62
Rubber hoses and hose assemblies for use in oil burners - Specification (ISO
6806:2014)
Gummischläuche und Schlauchleitungen für den Einsatz in Ölbrennern - Anforderung
(ISO 6806:2014)
Tuyaux et fexibles en caoutchouc pour brûleurs - Spécifications (ISO 6806:2014)
Ta slovenski standard je istoveten z: EN ISO 6806:2014
ICS:
27.060.10 *RULOQLNLQDWHNRþHLQWUGR Liquid and solid fuel burners
JRULYR
83.140.40 Gumene cevi Hoses
SIST EN ISO 6806:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 6806:2014

---------------------- Page: 2 ----------------------

SIST EN ISO 6806:2014

EUROPEAN STANDARD
EN ISO 6806

NORME EUROPÉENNE

EUROPÄISCHE NORM
September 2014
ICS 83.140.40; 27.060.10 Supersedes EN ISO 6806:1995
English Version
Rubber hoses and hose assemblies for use in oil burners -
Specification (ISO 6806:2014)
Tuyaux et fexibles en caoutchouc pour brûleurs - Gummischläuche und Schlauchleitungen für den Einsatz in
Spécifications (ISO 6806:2014) Ölbrennern - Anforderung (ISO 6806:2014)
This European Standard was approved by CEN on 7 June 2014.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6806:2014 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 6806:2014
EN ISO 6806:2014 (E)
Contents Page
Foreword .3
2

---------------------- Page: 4 ----------------------

SIST EN ISO 6806:2014
EN ISO 6806:2014 (E)
Foreword
This document (EN ISO 6806:2014) has been prepared by Technical Committee ISO/TC 45 “Rubber and
rubber products” in collaboration with Technical Committee CEN/TC 218 “Rubber and plastics hoses and
hose assemblies” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by March 2015, and conflicting national standards shall be withdrawn at
the latest by March 2015.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 6806:1995.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 6806:2014 has been approved by CEN as EN ISO 6806:2014 without any modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 6806:2014

---------------------- Page: 6 ----------------------

SIST EN ISO 6806:2014
INTERNATIONAL ISO
STANDARD 6806
Third edition
2014-09-15
Rubber hoses and hose assemblies for
use in oil burners — Specification
Tuyaux et flexibles en caoutchouc pour brûleurs — Spécifications
Reference number
IS
...