EN ISO 6806:2014
(Main)Rubber hoses and hose assemblies for use in oil burners - Specification (ISO 6806:2014)
Rubber hoses and hose assemblies for use in oil burners - Specification (ISO 6806:2014)
ISO 6806:2014 specifies the minimum requirements for rubber hoses and hose assemblies for use in oil burners.
The following two types of hose assembly are specified.
Type 1: Hose assemblies for flux and reflux, but not for insertion between the oil burner pump and the atomizing connection; maximum working pressure 1,0 MPa (10 bar); maximum oil temperature 100 °C.
Type 2: Hose assemblies for insertion between the oil burner pump and the atomizing connection; working pressure 4,0 MPa (40 bar); maximum oil temperature 100 °C.
Gummischläuche und Schlauchleitungen für den Einsatz in Ölbrennern - Anforderung (ISO 6806:2014)
Tuyaux et fexibles en caoutchouc pour brûleurs - Spécifications (ISO 6806:2014)
L'ISO 6806:2014 spécifie les exigences minimales pour les tuyaux et les flexibles en caoutchouc utilisés pour les brûleurs à fuel.
Les deux types suivants de flexibles sont spécifiés.
- Type 1: flexibles pour le flux et le reflux, mais pas pour l'installation entre la pompe du brûleur et le système de pulvérisation; pression maximale de service 1,0 MPa (10 bar); température maximale du fuel 100 °C.
- Type 2: flexibles pour installation entre la pompe du brûleur et le système de pulvérisation; pression maximale de service 4,0 MPa (40 bar); température maximale du fuel 100 °C.
Gumene cevi in cevni priključki za oljne gorilnike - Specifikacija (ISO 6806:2014)
Ta mednarodni standard določa minimalne zahteve za gumene cevi in cevne priključke
za oljne gorilnike.
Določena sta naslednja tipa cevnih priključkov.
– Tip 1: Cevni priključki za pretok in povratni pretok, a ne za vstavitev med črpalko oljnega gorilnika in
priključek za razprševanje; najvišji delovni tlak 1,0 MPa (10 bar); najvišja temperatura olja
100 °C.
– Tip 2: Cevni priključki za vstavitev med črpalko oljnega gorilnika in priključek za razprševanje;
delovni tlak 4,0 MPa (40 bar); najvišja temperatura olja 100 °C.
OPOMBA: Cevni priključki iz tega mednarodnega standarda niso namenjeni uporabi (brez
posebne ocene) za namene, ki niso inštalacije oljnih gorilnikov.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2014
1DGRPHãþD
SIST EN ISO 6806:2000
*XPHQHFHYLLQFHYQLSULNOMXþNL]DROMQHJRULOQLNH6SHFLILNDFLMD ,62
Rubber hoses and hose assemblies for use in oil burners - Specification (ISO
6806:2014)
Gummischläuche und Schlauchleitungen für den Einsatz in Ölbrennern - Anforderung
(ISO 6806:2014)
Tuyaux et fexibles en caoutchouc pour brûleurs - Spécifications (ISO 6806:2014)
Ta slovenski standard je istoveten z: EN ISO 6806:2014
ICS:
27.060.10 *RULOQLNLQDWHNRþHLQWUGR Liquid and solid fuel burners
JRULYR
83.140.40 Gumene cevi Hoses
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 6806
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2014
ICS 83.140.40; 27.060.10 Supersedes EN ISO 6806:1995
English Version
Rubber hoses and hose assemblies for use in oil burners -
Specification (ISO 6806:2014)
Tuyaux et fexibles en caoutchouc pour brûleurs - Gummischläuche und Schlauchleitungen für den Einsatz in
Spécifications (ISO 6806:2014) Ölbrennern - Anforderung (ISO 6806:2014)
This European Standard was approved by CEN on 7 June 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6806:2014 E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 6806:2014) has been prepared by Technical Committee ISO/TC 45 “Rubber and
rubber products” in collaboration with Technical Committee CEN/TC 218 “Rubber and plastics hoses and
hose assemblies” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by March 2015, and conflicting national standards shall be withdrawn at
the latest by March 2015.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 6806:1995.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 6806:2014 has been approved by CEN as EN ISO 6806:2014 without any modification.
INTERNATIONAL ISO
STANDARD 6806
Third edition
2014-09-15
Rubber hoses and hose assemblies for
use in oil burners — Specification
Tuyaux et flexibles en caoutchouc pour brûleurs — Spécifications
Reference number
ISO 6806:2014(E)
©
ISO 2014
ISO 6806:2014(E)
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved
ISO 6806:2014(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Construction . 1
4 Dimensions and tolerances . 2
4.1 Inside diameter . 2
4.2 Bend radii . 2
4.3 Thickness of lining and cover . 2
5 Physical requirements for lining and cover . 2
6 Physical requirements for hoses and hose assemblies . 3
6.1 Hydrostatic tests . 3
6.2 Oil swell . 3
6.3 External pressure test . 3
6.4 Low-temperature flexibility . 4
6.5 Flammability . 4
6.6 Ozone resistance (cover only) . 4
6.7 Impulse test . 4
7 Frequency of testing . 4
8 Type tests . 4
9 Marking . 4
Annex A (normative) Test frequency. 5
Annex B (informative) Production tests . 6
Annex C (normative) Determination of oil swell . 7
Annex D (normative) Determination of resistance to external pressure .8
Annex E (normative) Determination of flammability . 9
Annex F (normative) Pressure impulse test .11
Bibliography .12
ISO 6806:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 1,
Hoses (rubber and plastics).
This third edition cancels and replaces the second edition (ISO 6806:1992), of which it constitutes a
minor revision.
The following changes (mainly editorial) were made as required to bring the standard up to date.
— Clause 2 (Normative references) has been updated where necessary. Reference to ISO 4672 has been
replaced by ISO 10619-2 and the new titles of ISO 1307, ISO 1436 and ISO 4671 have been quoted.
— Wherever necessary the terminology has been amended to conform to ISO 8330.
— New Clause 7 (Frequency of testing) and Clause 8 (Type tests) have been introduced; new Annexes A
and B (Tables A.1 and B.1) have been introduced to standardize the frequency of the tests already
required in the previous edition (ISO 6806:1992).
— Clause 9 (Marking) has been amended (maximum working pressure and date of publication of this
International Standard to be marked on hose).
— No technical changes from requirements already specified in the second edition (ISO 6806:1992)
have been made.
iv © ISO 2014 – All rights reserved
INTERNATIONAL STANDARD ISO 6806:2014(E)
Rubber hoses and hose assemblies for use in oil burners —
Specification
1 Scope
This International Standard specifies the minimum requirements for rubber hoses and hose assemblies
for use in oil burners.
The following two types of hose assembly are specified.
— Type 1: Hose assemblies for flux and reflux, but not for insertion between the oil burner pump and
the atomizing connection; maximum working press
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.