Automatic shut-off valves for gas burners and gas appliances

EN 13611:2019, Clause 1 applies with the following modification and addition:
Modification:
The 1st paragraph of EN 13611:2019, Clause 1 is replaced by:
This document specifies the safety, design, construction, and performance requirements and testing for automatic shut-off valves for burners and appliances burning one or more gaseous fuels, hereafter referred to as “valves”.
This document is applicable to valves with declared maximum inlet pressures up to and including 500 kPa and of nominal connection sizes up to and including DN 250.
Addition:
This document is applicable to:
-   electrically actuated valves;
-   valves actuated by fluids where the control valves for these fluids are actuated electrically, but not to any external electrical devices for switching the control signal or actuating energy;
-   valves where the flow rate is controlled by external electrical signals, either in discrete steps or proportional to the applied signal;
-   valves fitted with closed position indicator switches.
An assessment method for valve designs is given by this document.
The 4th paragraph of EN 13611:2019, Clause 1 is removed.

Automatische Absperrventile für Gasbrenner und Gasgeräte

EN 13611:2019, Abschnitt 1, gilt mit folgender Änderung und Ergänzung:
Änderung:
Der erste Absatz von EN 13611:2019, Abschnitt 1, wird ersetzt durch:
Dieses Dokument legt die Sicherheits , Auslegungs , Konstruktions- und Leistungsanforderungen sowie die Prüfung von automatischen Absperrventilen für Brenner und Brennstoffgeräte für einen oder mehrere gasförmige Brennstoffe, nachstehend als „Ventile“ bezeichnet, fest.
Dieses Dokument gilt für Ventile mit einem angegebenen höchsten Eingangsdruck bis einschließlich 500 kPa und mit Anschlussnennweiten bis einschließlich DN 250.
Ergänzung:
Dieses Dokument gilt für:
—   Elektrisch betätigte Ventile;
—   Ventile, die durch Steuermedien betätigt werden, wenn die Steuerventile für diese Medien elektrisch betätigt werden, aber nicht für externe elektrische Elemente, die das Steuersignal oder die Antriebsenergie schalten;
—   Ventile mit Durchflussmengenregelung durch externe elektrische Signale entweder in Stufen oder proportional zum angelegten Signal;
—   Ventile mit Meldeschaltern für die geschlossene Stellung.
Dieses Dokument gibt ein Bewertungsverfahren für die Auslegung und Konstruktion von Ventilen an.
Der vierte Absatz von EN 13611:2019, Abschnitt 1, entfällt.

Robinets automatiques de sectionnement pour brûleurs à gaz et appareils à gaz

L’article 1 de la norme EN 13611:2019 s’applique avec la modification et l’addition suivantes :
Modification :
Le 1er paragraphe de l’article 1 de la norme EN 13611:2019 est remplacé par ce qui suit :
Le présent document spécifie les exigences de sécurité, de construction et de fonctionnement et les essais applicables aux robinets automatiques de sectionnement pour brûleurs à gaz, appareils à gaz et similaires, dénommés ci-après « robinets ».
Ce document s'applique aux robinets dont la pression amont maximale déclarée est inférieure ou égale à 500 kPa, de diamètres nominaux de raccordement inférieurs ou égaux à DN 250.
Addition :
Le document est applicable aux :
-   robinets de sectionnement commandés électriquement ;
-   robinets de sectionnement actionnés par des fluides si les vannes de commande de ces fluides sont commandées électriquement, mais en aucun cas aux dispositifs électriques externes commutant le signal de commande ou libérant l'énergie motrice de commande ;
-   robinets dans lesquels le débit est commandé par des signaux électriques externes, soit par pas, soit proportionnellement au signal reçu ;
-   robinets équipés de contacts indicateurs de position de fermeture.
Une méthode d'évaluation de la conception des robinets est donnée par le présent document.
Le 4ième paragraphe de l’article 1 de la EN 13611 :2019 est supprimé.

Samodejni zaporni ventili za plinske gorilnike in plinske aparate

General Information

Status
Published
Publication Date
11-Oct-2022
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
12-Oct-2022
Due Date
02-Feb-2022
Completion Date
12-Oct-2022

Relations

Buy Standard

Standard
EN 161:2022
English language
66 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-december-2022
Nadomešča:
SIST EN 161:2011+A3:2013
Samodejni zaporni ventili za plinske gorilnike in plinske aparate
Automatic shut-off valves for gas burners and gas appliances
Automatische Absperrventile für Gasbrenner und Gasgeräte
Robinets automatiques de sectionnement pour brûleurs à gaz et appareils à gaz
Ta slovenski standard je istoveten z: EN 161:2022
ICS:
23.060.10 Zapirni ventili (kroglasti) Globe valves
27.060.20 Plinski gorilniki Gas fuel burners
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 161
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2022
EUROPÄISCHE NORM
ICS 23.060.10 Supersedes EN 161:2011+A3:2013
English Version
Automatic shut-off valves for gas burners and gas
appliances
Robinets automatiques de sectionnement pour Automatische Absperrventile für Gasbrenner und
brûleurs à gaz et appareils à gaz Gasgeräte
This European Standard was approved by CEN on 1 August 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 161:2022 E
worldwide for CEN national Members.

Contents Page
European foreword . 4
Introduction . 6
1 Scope . 8
2 Normative references . 8
3 Terms and definitions . 9
4 Classification . 11
4.1 Classes of control . 11
4.2 Groups of control . 11
4.3 Classes of control functions . 11
4.4 Types of DC supplied controls . 11
5 Test conditions and uncertainty of measurements . 11
6 Design and construction . 11
6.1 General . 11
6.2 Mechanical parts of the control . 11
6.3 Materials . 14
6.4 Gas connections . 15
6.5 Electrical parts of the control . 15
6.6 Protection against internal faults for the purpose of functional safety . 16
6.101 Pneumatic and hydraulic actuating mechanisms . 16
7 Performance. 16
7.1 General . 16
7.2 Leak-tightness . 16
7.3 Torsion and bending . 16
7.4 Rated flow rate . 17
7.5 Durability . 17
7.6 Performance tests for electronic controls . 17
7.7 Long-term performance for electronic controls . 17
7.8 Data exchange. 17
7.101 Closing function . 17
7.102 Closing force . 18
7.103 Delay time and opening time . 18
7.104 Closing time . 19
7.105 Sealing force . 19
7.106 Closed position indicator switch . 21
7.107 Endurance . 21
8 Electrical requirements . 23
8.1 General . 23
8.2 Protection by enclosure . 23
8.101 Switches . 23
8.102 Plug connections . 23
8.103 Power saving circuits . 24
9 Electromagnetic compatibility (EMC) . 24
9.1 Protection against environmental influences . 24
9.2 Supply voltage variations below 85 % of rated voltage . 24
9.3 Voltage dips and interruptions . 24
9.4 Supply frequency variations . 25
9.5 Surge immunity tests . 25
9.6 Electrical fast transient/burst . 25
9.7 Immunity to conducted disturbances induced by radio frequency fields . 25
9.8 Immunity to radiated disturbances induced by radio frequency fields . 25
9.9 Electrostatic discharge tests . 25
9.10 Power frequency magnetic field immunity tests . 25
9.11 Harmonics and interharmonics including mains signalling at a. c. power port, low
frequency immunity tests . 25
10 Marking, instructions . 25
10.1 Marking . 25
10.2 Instructions . 26
10.3 Warning notice . 27
Annex A (informative) Abbreviations and symbols . 28
Annex B (informative) Leak-tightness test for gas controls – volumetric method . 29
Annex C (informative) Leak-tightness test for gas controls – pressure loss method . 30
Annex D (normative) Calculation of pressure loss into leakage rate . 31
Annex E (normative) Electrical/electronic component fault modes . 32
Annex F (normative) Additional requirements for safety accessories and pressure
accessories as defined in EU Directive 2014/68/EU . 33
Annex G (normative) Materials for pressurized parts . 34
Annex H (normative) Additional materials for pressurized parts . 35
Annex I (normative) Requirements for controls used in DC supplied burners and
appliances burning gaseous or liquid fuels . 36
Annex J (normative) Method for the determination of a Safety Integrity Level (SIL) . 37
Annex K (normative) Method for the determination of a Performance Level (PL) . 38
K.1 Scope . 38
K.2 Normative references. 38
K.3 Terms and definitions . 38
K.4 Performance . 38
K.5 Marking, instructions . 40
Annex L (informative) Relationship between Safety Integrity Level (SIL) and Performance
Level (PL) . 41
Annex M (normative) Reset functions . 42
Annex N (informative) Guidance document on Environmental Aspects . 43
Annex O (normative) Seals of elastomer, cork and synthetic fibre mixtures . 44
Annex AA (informative) Model of a FMEA for valves . 45
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Regulation (EU) 2016/426 aimed to be covered . 63
Bibliography .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.