Geometrical product specifications (GPS) - Surface texture: Profile method; Measurement standards - Part 2: Software measurement standards (ISO 5436-2:2012)

This part of ISO 5436 defines Type F1 and Type F2 software measurement standards (etalons) for verifying the software of measuring instruments. It also defines the file format of Type F1 software measurement standards for the calibration of instruments used for measuring the surface texture by the profile method defined in ISO 3274.
NOTE 1 Throughout this part of ISO 5436, the term "softgauge" is used as a substitute for "software measurement standard Type F1".
NOTE 2 Formerly, "measurement standards" were referred to as "calibration specimens".
NOTE 3 ISO 3274 only refers to instruments with independent reference datums.

Geometrische Produktspezifikation (GPS) - Oberflächenbeschaffenheit: Tastschnittverfahren; Normale - Teil 2: Software-Normale (ISO 5436-2:2012)

Dieser Teil von ISO 5436 legt die Software-Normale (Etalons) vom Typ F1 und F2 für die Prüfung der Software von Messgeräten fest. Außerdem legt er das Datenformat der Typ-F1-Software-Normale zur Kalibrierung von Messgeräten zur Messung der Oberflächenbeschaffenheit mit dem Profilverfahren nach ISO 3274 fest.
ANMERKUNG 1   In diesem Teil von ISO 5436 wird der Begriff „Software-Normale vom Typ F1“ durch „Software-Lehre“ ersetzt.
ANMERKUNG 2   Früher wurden „Normale“ als „Einstellnormale“ bezeichnet.
ANMERKUNG 3   ISO 3274 bezieht sich nur auf Messgeräte mit unabhängigen Bezügen.

Spécification géométrique des produits (GPS) - État de surface: Méthode du profil; Étalons - Partie 2: Étalons logiciels (ISO 5436-2:2012)

La présente partie de l'ISO 5436 définit les étalons logiciels de Type F1 et de Type F2, pour vérifier les logiciels des instruments de mesure. Elle définit également le format de fichier des étalons logiciels de Type F1 pour l'étalonnage d'instruments de mesure de l'état de surface par la méthode du profil telle que définie dans l'ISO 3274.
NOTE 1 Tout au long de la présente partie de l'ISO 5436, «calibre virtuel» est utilisé en remplacement d'«étalon logiciel de Type F1».
NOTE 2 Précédemment, les «étalons» étaient appelés «échantillons d'étalonnage».
NOTE 3 L'ISO 3274 se réfère uniquement à des instruments intégrant leur référence de guidage.

Specifikacija geometrijskih veličin izdelka - Tekstura površine: profilna metoda - Standardi za merjenje - 2. del: Standardi za merilno programsko opremo (ISO 5436-2:2012)

Ta del standarda ISO 5436 določa standarde za merilno programsko opremo tipov F1 in F2 (etalon) za preverjanje programske opreme merilnih instrumentov. Določa tudi obliko zapisa datoteke standardov za merilno programsko opremo tipa F1 za kalibracijo instrumentov, ki se uporabljajo za merjenje teksture površine s profilno metodo, ki jo določa standard ISO 3274.

General Information

Status
Published
Publication Date
30-Sep-2012
Withdrawal Date
29-Apr-2013
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
01-Oct-2012
Completion Date
01-Oct-2012

Relations

Buy Standard

Standard
EN ISO 5436-2:2013
English language
25 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 5436-2:2013
01-oktober-2013
1DGRPHãþD
SIST EN ISO 5436-2:2004
SIST EN ISO 5436-2:2004/AC:2008
SIST EN ISO 5436-2:2004/oprA1:2010
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND7HNVWXUDSRYUãLQHSURILOQDPHWRGD
6WDQGDUGL]DPHUMHQMHGHO6WDQGDUGL]DPHULOQRSURJUDPVNRRSUHPR ,62

Geometrical product specifications (GPS) - Surface texture: Profile method;
Measurement standards - Part 2: Software measurement standards (ISO 5436-2:2012)
Geometrische Produktspezifikation (GPS) - Oberflächenbeschaffenheit:
Tastschnittverfahren; Normale - Teil 2: Software-Normale (ISO 5436-2:2012)
Spécification géométrique des produits (GPS) - État de surface: Méthode du profil;
Étalons - Partie 2: Étalons logiciels (ISO 5436-2:2012)
Ta slovenski standard je istoveten z: EN ISO 5436-2:2012
ICS:
17.040.30 Merila Measuring instruments
SIST EN ISO 5436-2:2013 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 5436-2:2013


EUROPEAN STANDARD
EN ISO 5436-2

NORME EUROPÉENNE

EUROPÄISCHE NORM
October 2012
ICS 17.040.30 Supersedes EN ISO 5436-2:2001
English Version
Geometrical product specifications (GPS) - Surface texture:
Profile method; Measurement standards - Part 2: Software
measurement standards (ISO 5436-2:2012)
Spécification géométrique des produits (GPS) - État de Geometrische Produktspezifikation (GPS) -
surface: Méthode du profil; Étalons - Partie 2: Étalons Oberflächenbeschaffenheit: Tastschnittverfahren; Normale
logiciels (ISO 5436-2:2012) - Teil 2: Software-Normale (ISO 5436-2:2012)
This European Standard was approved by CEN on 25 September 2012.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 5436-2:2012: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

SIST EN ISO 5436-2:2013
EN ISO 5436-2:2012 (E)
Contents Page
Foreword .3

2

---------------------- Page: 3 ----------------------

SIST EN ISO 5436-2:2013
EN ISO 5436-2:2012 (E)
Foreword
This document (EN ISO 5436-2:2012) has been prepared by Technical Committee ISO/TC 213 "Dimensional
and geometrical product specifications and verification" in collaboration with Technical Committee
CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of which is
held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2013, and conflicting national standards shall be withdrawn at the
latest by April 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 5436-2:2001.
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 5436-2:2012 has
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.