EN 1442:2006+A1:2008
(Main)LPG equipment and accessories - Transportable refillable welded steel cylinders for LPG - Design and construction
LPG equipment and accessories - Transportable refillable welded steel cylinders for LPG - Design and construction
This European Standard specifies the minimum requirements for the design, construction and testing during manufacture of transportable refillable welded steel Liquefied Petroleum Gas (LPG) cylinders, of water capacity from 0,5 l up to and including 150 l, exposed to ambient temperatures.
This European Standard applies only to cylinders having a circular cross-section.
Flüssiggas-Geräte und Ausrüstungsteile - Ortsbewegliche, wiederbefüllbare, geschweißte Flaschen aus Stahl für Flüssiggas (LPG) - Gestaltung und Konstruktion
Diese Europäische Norm legt Mindestanforderungen an die Gestaltung, Konstruktion und Prüfung während der Herstellung von ortsbeweglichen, wiederbefüllbaren, geschweißten Flüssiggasflaschen (LPG) aus Stahl mit einem Fassungsraum von 0,5 l bis einschließlich 150 l fest, wenn diese der Umgebungstemperatur ausgesetzt werden.
Diese Europäische Norm gilt nur für Flaschen mit kreisförmigem Querschnitt.
Équipements pour GPL et leurs accessoires - Bouteilles en acier soudé transportables et rechargeables pour gaz de pétrole liquéfiés (GPL) - Conception et fabrication
La présente Norme européenne spécifie les exigences minimales concernant la conception, la construction et les
essais lors de la fabrication des bouteilles en acier soudé, transportables et rechargeables pour gaz de pétrole
liquéfié (GPL) d’une capacité en eau comprise entre 0,5 l et 150 l inclus, soumises à la température ambiante.
La présente Norme européenne s’applique uniquement aux bouteilles de section transversale circulaire.
Oprema in pribor za utekočinjeni naftni plin (UNP) - Ponovno polnljive varjene plinske jeklenke za UNP - Konstruiranje in izdelava
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Flüssiggas-Geräte und Ausrüstungsteile - Ortsbewegliche, wiederbefüllbare, geschweißte Flaschen aus Stahl für Flüssiggas (LPG) - Gestaltung und KonstruktionÉquipements pour GPL et leurs accessoires - Bouteilles en acier soudé transportables et rechargeables pour gaz de pétrole liquéfiés (GPL) - Conception et fabricationLPG equipment and accessories - Transportable refillable welded steel cylinders for LPG - Design and construction23.020.35Plinske jeklenkeGas cylindersICS:Ta slovenski standard je istoveten z:EN 1442:2006+A1:2008SIST EN 1442:2006+A1:2008en,fr,de01-april-2008SIST EN 1442:2006+A1:2008SLOVENSKI
STANDARDSIST EN 1442:20061DGRPHãþD
SIST EN 1442:2006+A1:2008
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1442:2006+A1
January 2008 ICS 23.020.30 Supersedes EN 1442:2006English Version
LPG equipment and accessories - Transportable refillable welded steel cylinders for LPG - Design and construction
Équipements pour GPL et leurs accessoires - Bouteilles en acier soudé transportables et rechargeables pour gaz de pétrole liquéfiés (GPL) - Conception et fabrication
Flüssiggas-Geräte und Ausrüstungsteile - Ortsbewegliche, wiederbefüllbare, geschweißte Flaschen aus Stahl für Flüssiggas (LPG) - Gestaltung und Konstruktion This European Standard was approved by CEN on 18 May 2006 and includes Amendment 1 approved by CEN on 20 December 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2008 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1442:2006+A1:2008: ESIST EN 1442:2006+A1:2008
EN 1442:2006+A1:2008 (E) 2 Contents Page Foreword.4 Introduction.5 1 Scope.6 2 Normative references.6 3 Terms, definitions and symbols.7 3.1 Terms and definitions.7 3.2 Symbols.7 4 Materials.8 5 Design.9 5.1 General requirements.9 5.2 Calculation of cylindrical shell thickness.10 5.3 Design of torispherical and semi-ellipsoidal ends concave to pressure.10 5.4 Design of ends of shapes other than torispherical and semi-ellipsoidal.14 5.5 Minimum wall thickness.14 5.6 Design of openings.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.