EN 14814:2007

Adhesives for thermoplastic piping systems for fluids under pressure - Specifications

This European Standard specifies the functional requirements and test methods for adhesives used for joining the components of unplasticised poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C), acrylonitrile -butadiene-styrene (ABS) thermoplastic piping systems for fluids under pressure.
It provides for the evaluation of conformity of the adhesive for this EN.

Klebstoffe für Druckrohrleitungssysteme aus thermoplastischen Kunststoffen für Fluide - Festlegungen

Diese Europäische Norm legt funktionelle Anforderungen an und Prüfverfahren für Klebstoffe fest, die zum Verbinden der Bauteile von thermoplastischen Druckrohrleitungssystemen aus weichmacherfreiem Poly¬vinylchlorid (PVC U), chloriertem Polyvinylchlorid (PVC C), Acrylnitril-Butadien-Styrol (ABS) für Flüssigkeiten verwendet werden.
Diese Europäische Norm legt die Bewertung der Konformität des Klebstoffes fest.

Adhésifs pour systèmes de canalisations thermoplastiques pour liquides sous pression - Spécifications

Lepila za plastomerne cevne sisteme za tekočine pod tlakom - Specifikacije

General Information

• Status: Withdrawn
• Publication Date: 27-Feb-2007
• Withdrawal Date: 17-May-2016
• ICS: 83.180 - Adhesives
• Technical Committee: CEN/TC 193 - Adhesives
• Drafting Committee: CEN/TC 193/WG 6 - Adhesives for thermoplastic piping systems
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 18-May-2016
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Directive: 89/106/EEC - Construction products
• Mandate: M/131 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on pipes, tanks and ancillaries, not in contact with water intended for human consumption
• Mandate: M/136 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on construction products in contact with water intended for human consumption
• Ref Project: SIST EN 14814:2007 - Adhesives for thermoplastic piping systems for fluids under pressure - Specifications

Relations

• Replaced By: EN 14814:2016 - Adhesives for thermoplastic piping systems for fluids under pressure - Specifications
• Effective Date: 25-May-2016

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Adhesives for thermoplastic piping systems for fluids under pressure - SpecificationsLILNDFLMHAdhésifs pour systemes de canalisations thermoplastiques pour liquides sous pression - SpécificationsKlebstoffe für Druckrohrleitungssysteme aus thermoplastischen Kunststoffen für Fluide - FestlegungenTa slovenski standard je istoveten z:EN 14814:2007SIST EN 14814:2007en,fr,de83.180LepilaAdhesivesICS:SLOVENSKI
STANDARDSIST EN 14814:200701-september-2007

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14814February 2007ICS 83.180 English VersionAdhesives for thermoplastic piping systems for fluids underpressure - SpecificationsAdhésifs pour systèmes de canalisations thermoplastiquespour liquides sous pression - SpécificationsKlebstoffe für Druckrohrleitungssysteme austhermoplastischen Kunststoffen für Fluide - FestlegungenThis European Standard was approved by CEN on 29 December 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14814:2007: E

Possible characterization test methods for adhesives for thermoplastic piping systems.14 Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of EU Directive 89/106/EEC, EU Construction Products Directive.15 ZA.1
Scope and relevant characteristics.15 ZA.2
Procedure(s) for the attestation of conformity of adhesives for thermoplastic piping systems for fluids under pressure.16 ZA.2.1
Systems of attestation of conformity.16 ZA.2.2 Declaration of conformity.17 ZA.3
CE Marking.17 Bibliography.20

and health practices and to ensure compliance with any regulatory conditions.

1 Scope This European Standard specifies the functional requirements and test methods for adhesives used for joining the components of unplasticised poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C), acrylonitrile -butadiene-styrene (ABS) thermoplastic piping systems for fluids under pressure. It provides for the evaluation of conformity of the adhesive for this EN. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 923:2005, Adhesives - Terms and definitions EN 1452 Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U)
EN ISO 9001:2000 , Quality management systems - Requirements (ISO 9001:2000) EN ISO 9311-1, Adhesives for thermoplastic piping systems - Part 1: Determination of film properties (ISO 9311-1:2005) EN ISO 9311-2, Adhesives for thermoplastic piping systems - Part 2: Determination of shear strength (ISO 9311-2:2002) EN ISO 9311-3, Adhesives for thermoplastic piping systems - Part 3: Test method for the determination of resistance to internal pressure (ISO 9311-3:2005) EN ISO 15493, Plastics piping systems for industrial applications - Acrylonitrile-butadiene-styrene (ABS), unplasticized poly(vinyl chloride) (PVC-U) and chlorinated poly(vinyl chloride) (PVC-C) - Specifications for components and the system - Metric series (ISO 15493:2003) EN ISO 15877, Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 923:2005 and the following apply. 3.1 diametric clearance difference between the mean outside diameter (dem) of the pipe and the mean inside diameter (dsm) of the socket 3.2 Definitions related to assessment of conformity
3.2.1 conformity assessment
any activity concerned with determining directly or indirectly that relevant requirements are fulfilled [EN 45020:2006]

test performed by the manufacturer on a batch of components, which has to be satisfactorily completed before the batch can be released [EN 13566-1:2002]
3.2.3 Initial Type Test (ITT)
complete set of test or other procedures, determining the performance of samples of products representative of the product type 3.2.4 Type Test (TT)
test performed to prove that the material, component, joint or assembly is capable of conforming with the relevant requirements given in the System Standard [CEN ISO/TS 15874-7:2003] 4 Requirements 4.1 General consideration The manufacturer of the adhesive shall specify for which pressure system the adhesive is intended to be used, e.g. PVC-U for water supply (see EN 1452 series), ABS, PVC-U or PVC-C for industrial applications (see EN ISO 15493) or PVC-C for hot and cold water installations (see EN ISO 15877). Unless otherwise specified in this clause, the test pieces shall fulfil the following requirements set in Tables 1 and 2:

Diametric clearance Material Diametric clearance mm ABS
−1,006,0 PVC-C −1,006,0
PVC-U −1,006,0 NOTE
The value and tolerances proposed for PVC-C systems are not based on a wide experience. The proposed value, 0,6 mm, seem to be the most adequate at the moment, but it will be followed closely throughout the implementation of this standard. Changes will be introduced, if necessary, in the future revision of this standard.
Table 2 —
Setting time Material Relative Humidity % Setting time Setting temperature °C ABS (50 ± 5) 1 h 24 h 480 h + 96 h (23 ± 2 ) (23 ± 2) (23 ± 2)+ (40 ± 2) PVC-C (50 ± 5) 1 h 24 h 480 h + 96 h (23 ± 2) (23 ± 2) (23 ± 2) + (80 ± 2) PVC-U (50 ± 5) 1 h 24 h 480 h + 96 h (23 ± 2) (23 ± 2) (23 ± 2) + (60 ± 2)
Setting time shall be measured from the beginning of the application of the adhesive.

Shear strength Material Test temperature °C Setting time
Requirements for shear strength MPa
ABS
(23 ± 2) 1 h 24 h 480 h + 96 h 0,1 1,5 5,0
PVC-C
(23 ± 2) 1 h 24 h 480 h + 96 h 0,4 1,5 10,0
PVC-U
(23 ± 2) 1 h 24 h 480 h + 96 h 0,4 1,5 7,0 NOTE
The value and tolerances proposed for PVC-C systems are not based on a wide experience. The proposed values seem to be the most adequate at the moment, but they will be followed closely throughout the implementation of this standard. Changes will be introduced, if necessary, in the future revision of this standard.
4.3 Pressure resistance The adhesive shall be tested in accordance with EN ISO 9311-3 using pipe and fitting compatible with the claims of the adhesive suitability. The test r
...