EN 4115:2010

Aerospace series - Cushion, rubber for clamps - Dimensions, masses

This standard specifies the required characteristics for rubber cushions used on clamps according to EN 3730, EN 4113, EN 4114.
For temperature range and environmental conditions see Table 1.

Luft- und Raumfahrt - Profilgummi für Schellen - Maße, Massen

Diese Norm legt die Anforderungen an Profilgummi für Schellen nach EN 3730, EN 4113 und EN 4114 fest.
Für den Temperaturbereich und die Umgebungsbedingungen siehe Tabelle 1.

Série aérospatiale - Profilé en élastomère pour colliers - Dimensions, masses

Aeronavtika - Prevleka iz gume za objemke - Mere, mase

Ta standard opredeljuje zahtevane lastnosti za prevleke iz gume za objemke v skladu z EN 3730, EN 4113, EN 4114. Za temperaturni razpon in okoljske pogoje glej Preglednico 1.

General Information

• Status: Published
• Publication Date: 06-Apr-2010
• Withdrawal Date: 30-Oct-2010
• ICS: 49.025.40 - Rubber and plastics
• ICS: 49.030.99 - Other fasteners
• Technical Committee: ASD-STAN - Aerospace
• Drafting Committee: ASD-STAN/D 3 - Mechanical
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 07-Apr-2010
• Completion Date: 07-Apr-2010
• Ref Project: SIST EN 4115:2010 - Aerospace series - Cushion, rubber for clamps - Dimensions, masses

Relations

• Replaces: EN 4115:2001 - Aerospace series - Cushion, rubber for clamps - Dimensions, masses
• Effective Date: 12-Apr-2010

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aeronavtika - Prevleka iz gume za objemke - Mere, maseLuft- und Raumfahrt - Profilgummi für Schellen - Maße, MassenSérie aérospatiale - Profilé en élastomère pour colliers - Dimensions, massesAerospace series - Cushion, rubber for clamps - Dimensions, masses49.060Aerospace electric equipment and systemsICS:Ta slovenski standard je istoveten z:EN 4115:2010SIST EN 4115:2010en01-junij-2010SIST EN 4115:2010SLOVENSKI
STANDARDSIST EN 4115:20021DGRPHãþD



SIST EN 4115:2010



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 4115
April 2010 ICS 49.025.40; 49.030.99 English Version
Aerospace series - Cushion, rubber for clamps - Dimensions, masses
Série aérospatiale - Profilé en élastomère pour colliers - Dimensions, masses
Luft- und Raumfahrt - Profilgummi für Schellen - Maße, Massen This European Standard was approved by CEN on 16 January 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4115:2010: ESIST EN 4115:2010



EN 4115:2010 (E) 2 Contents Page Foreword .31Scope .42Normative references .43Required characteristics .54Designation .75Marking .86Quality assurance .87Technical specification .88Packaging .8Bibliography .9 SIST EN 4115:2010



EN 4115:2010 (E) 3 Foreword This document (EN 4115:2010) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2010, and conflicting national standards shall be withdrawn at the latest by October 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Eston
...