iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 10028-6:1996

(Main)

Flat products made of steels for pressure purposes - Part 6: Weldable fine grain steels, quenched and tempered

Flat products made of steels for pressure purposes - Part 6: Weldable fine grain steels, quenched and tempered

This part of EN 10028 specifies the requirements for flat products for pressure equipments made of liquid quenched and tempered steels as listed in table 1.  Other parts of this European Standard are:  EN 10028-1 Flat products made of steels for pressure purposes - General requirements  EN 10028-2 Flat products made of steels for pressure purposes - Part 2 : Non-alloy and alloy steels with specified elevated temperature properties  EN 10028-3 Flat products made of steels for pressure purposes - Part 3 : Weldable fine grain steels, normalized  EN 10028-4 Flat products made of steels for pressure purposes - Part 4 : Nickel alloy steels with specified low temperature properties  EN 10028-5 Flat products made of steels for pressure purposes - Part 5 : Weldable fine grain steels, thermomechanically rolled  EN 10028-7 Flat products made of steels for pressure purposes - Part 7 : Stainless steels

Flacherzeugnisse aus Druckbehälterstählen - Teil 6: Schweißgeeignete Feinkornbaustähle, vergütet

1. Diese Europäische Norm EN 10028 Teil 6 legt die Anforderungen an Flacherzeugnisse für Druckbehälter aus flüssigkeitsvergüteten Stählen nach Tabelle 1 fest.

Produits plats en aciers pour appareils à pression - Partie 6: Aciers soudables à grains fins, trempés et revenus

1. La présente norme EN 10028 partie 6, traite des spécifications relatives aux produits plats pour appareils à pression en aciers à l'état obtenu par trempe dans un liquide avec des caractéristiques conformes aux indications du tableau 1.

Ploščati jekleni izdelki za tlačne posode - 6. del: Variva drobnozrnata jekla, poboljšana

General Information

Status
Withdrawn
Publication Date
10-Dec-1996
Withdrawal Date
24-Jun-2003
ICS
77.140.50 - Flat steel products and semi-products
Technical Committee
ECISS/TC 107 - Steels for pressure purposes
Drafting Committee
ECISS/TC 22 - Steels for pressure purposes - Qualities
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
25-Jun-2003
Completion Date
25-Jun-2003
Directive
97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
Mandate
M/071 - Mandate to CEN for standardization in the field of Pressure equipment
Ref Project
SIST EN 10028-6:1997 - Flat products made of steels for pressure purposes - Part 6: Weldable fine grain steels, quenched and tempered

Relations

Replaced By
EN 10028-6:2003 - Flat products made of steels for pressure purposes - Part 6: Weldable fine grain steels, quenched and tempered
Effective Date
22-Dec-2008

Buy Standard

EN 10028-6:1997EN 10028-6:1997
PreviousNext
Standard
EN 10028-6:1997
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.SREROMãDQDFlacherzeugnisse aus Druckbehälterstählen - Teil 6: Schweißgeeignete Feinkornbaustähle, vergütetProduits plats en aciers pour appareils a pression - Partie 6: Aciers soudables a grains fins, trempés et revenusFlat products made of steels for pressure purposes - Part 6: Weldable fine grain steels, quenched and tempered77.140.50SROL]GHONLFlat steel p
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 10028-2:2017(Main)
Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties
SIST EN 10028-2:2017

This European Standard specifies requirements for flat products for pressure equipment made of weldable non-alloy and alloy steels with elevated temperature properties as specified in Table 1.
The requirements and definitions of EN 10028-1:2017 also apply.
NOTE   Once this European Standard is published in the EU Official Journal (OJEU) under Directive 2014/68/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014/68/EU is limited to technical data of materials in this European Standard (Part 1 and this Part 2 of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 2014/68/EU are satisfied, needs to be done.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10028-3:2017(Main)
Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized
SIST EN 10028-3:2017

This European Standard specifies requirements for flat products for pressure equipment made of weldable fine grain steels as specified in Table 1.
NOTE 1   Fine grain steels are understood as steels with a ferritic grain size of 6 or finer when tested in accordance with EN ISO 643.
The requirements and definitions of EN 10028-1:2017 also apply.
NOTE 2   Once this European Standard is published in the EU Official Journal (OJEU) under Directive 2014/68/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014/68/EU is limited to technical data of materials in this European Standard (Part 1 and the other relevant part of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 2014/68/EU are satisfied, needs to be done.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10028-6:2017(Main)
Flat products made of steels for pressure purposes - Part 6: Weldable fine grain steels, quenched and tempered
SIST EN 10028-6:2017

This European Standard specifies the requirements for flat products for pressure equipment made of quenched and tempered steels as specified in Table 1.
The requirements in FprEN 10028-1:2017 also apply.
NOTE   Once this European Standard is published in the EU Official Journal (OJEU) under Directive 2014/68/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014/68/EU is limited to technical data of materials in this European Standard (Part 1 and the other relevant part of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 2014/68/EU are satisfied, needs to be done.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10028-1:2017(Main)
Flat products made of steels for pressure purposes - Part 1: General requirements
SIST EN 10028-1:2017

This European Standard specifies general technical delivery conditions for flat products for the construction of pressure equipment.
The general technical delivery conditions in EN 10021 also apply.
NOTE   Once this European Standard is published in the EU Official Journal (OJEU) under Directive 2014/68/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014/68/EU is limited to technical data of materials in this European Standard (Part 1 and the other relevant part of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 2014/68/EU are satisfied, needs to be done.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10028-5:2017(Main)
Flat products made of steels for pressure purposes - Part 5: Weldable fine grain steels, thermomechanically rolled
SIST EN 10028-5:2017

This European Standard specifies the requirements for flat products for pressure equipment made of thermomechanically rolled steels as specified in Table 1.
The steels are not suitable for hot forming.
NOTE 1   At the time of publication of this European Standard, no sufficient data for the standardization of the elevated temperature properties of these steels was available.
If their use at such temperatures is intended the conditions for this should be specially agreed between the interested parties.
The requirements of EN 10028 1:2017 also apply.
NOTE 2   Once this European Standard is published in the EU Official Journal (OJEU) under Directive 2014/68/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014/68/EU is limited to technical data of materials in this European Standard (Part 1 and the other relevant part of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 2014/68/EU are satisfied, needs to be done.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10028-4:2017(Main)
Flat products made of steels for pressure purposes - Part 4: Nickel alloy steels with specified low temperature properties
SIST EN 10028-4:2017

This European Standard specifies requirements for flat products for pressure equipment made of nickel alloy steels as specified in Table 1.
The requirements and definitions of EN 10028-1:2017 also apply.
NOTE   Once this European Standard is published in the EU Official Journal (OJEU) under Directive 2014/68/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014/68/EU is limited to technical data of materials in this European Standard (Part 1 and the other relevant part of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 2014/68/EU are satisfied, needs to be done.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10120:2017(Main)
Steel sheet and strip for welded gas cylinders
SIST EN 10120:2017

This European Standard specifies requirements for sheet and strip up to 5 mm thickness of steels listed in Table 1 and intended for the manufacture of welded gas cylinders.
The general technical delivery conditions in EN 10021 also apply to products supplied in accordance with this European Standard.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10028-7:2016(Main)
Flat products made of steels for pressure purposes - Part 7: Stainless steels
SIST EN 10028-7:2016

This European Standard specifies requirements for flat products for pressure purposes made of stainless steels, including austenitic creep resisting steels, in thicknesses as indicated in Tables 7 to 10.
The requirements of EN 10028-1:2007+A1:2009 also apply.
NOTE 1   The steel grades covered by this European Standard have been selected from EN 10088-1.
NOTE 2   Once this European Standard is published in the Official Journal of the European Union (OJEU) under Directive 97/23/EC, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 97/23/EC is limited to technical data of materials in this European Standard (Part 1 and Part 7) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done.

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10209:2023(Main)
Cold rolled low carbon steel flat products for vitreous enamelling - Technical delivery conditions
SIST EN 10209:2023

This document applies to cold rolled non-coated low carbon steel flat products in rolled widths equal to or over 600 mm and in thicknesses equal to or less than 3 mm, delivered in sheet, wide strip, slit wide strip or cut lengths obtained from slit wide strip or sheet.
It does not apply to cold rolled narrow strip (rolling width < 600 mm) or to cold rolled flat products for which there is a specific standard, in particular the following:
-   cold-rolled low carbon steel flat products for cold forming (EN 10130);
-   cold-rolled non-oriented electrical steel sheet and strip delivered in fully processed state (EN 10106);
-   cold rolled electrical non-alloy and alloy steel sheet and strip delivered in the semi-processed state (EN 10341);
-   cold reduced blackplate (EN 10205);
-   steel sheet and strip for welded gas cylinders (EN 10120);
-   cold-rolled uncoated non-alloy mild steel narrow strip for cold forming (EN 10139);
-   cold-rolled structural steels for general purposes;
-   cold-rolled flat products made of high yield strength for cold forming (EN 10268).

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10359:2023(Main)
Laser welded tailored blanks - Technical delivery conditions
SIST EN 10359:2023

This document specifies the requirements for laser welded tailored blanks (LWB) made of steels for all cold or hot forming processes.
This document is applicable to all steel grades with or without metallic and/or organic coatings, having uniform or different sheet thickness, welded with or without extra material addition.
After the welding process, LWB are further processed to pressed parts by forming operations under the responsibility of the processor.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day