iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 27509:2020

(Main)

Petroleum and natural gas industries - Compact flanged connections with IX seal ring (ISO 27509:2020)

Petroleum and natural gas industries - Compact flanged connections with IX seal ring (ISO 27509:2020)

This document specifies detailed manufacturing requirements for circular steel and nickel alloy compact flanged connections and associated seal rings, for designated pressures and temperatures in class designations CL 150 (PN 20) to CL 1500 (PN 260) for nominal sizes from DN 15 (NPS ½) to DN 1200 (NPS 48), and for CL 2500 (PN 420) for nominal sizes from DN 15 (NPS ½) to DN 600 (NPS 24).
NOTE     NPS is expressed in accordance with ASME B36.10M and ASME B36.19M.
This document is applicable to welding neck flanges, blind flanges, paddle spacers and spacer blinds (paddle blanks), valve/equipment integral flanges, orifice spacers, reducing threaded flanges and rigid interfaces for use in process piping for the petroleum, petrochemical and natural gas industries.
This document is applicable within a temperature range from −196 °C to +250 °C.
This document is not applicable for external pressure.

Erdöl- und Erdgasindustrie - Kompakte Flanschverbindungen mit IX Dichtungsring (ISO 27509:2020)

Industries du pétrole et du gaz naturel - Raccordements à brides compactes avec bague d'étanchéité IX (ISO 27509:2020)

Le présent document spécifie en détail les exigences de fabrication des assemblages à brides circulaires compactes en alliage d'acier et de nickel, ainsi que des bagues d'étanchéité associées, pour les pressions et températures désignées dans les classes CL 150 (PN 20) à CL 1500 (PN 260) pour les dimensions nominales DN 15 (NPS ½) à DN 1200 (NPS 48), et pour CL 2500 (PN 420) pour les dimensions nominales DN 15 (NPS ½) à DN 600 (NPS 24).
NOTE       NPS est exprimé conformément aux normes ASME B36.10M et ASME B36.19M.
Le présent document est applicable aux brides à collerette à souder bout à bout, aux brides pleines, aux entretoises creuses et aux obturateurs d'entretoise (tampons pleins), aux brides incorporées des robinetteries/équipements, aux entretoises à orifices, aux brides de réduction filetées et aux interfaces rigides des tuyauteries process utilisées dans les industries du pétrole, de la pétrochimie et du gaz naturel.
Le présent document s'applique à une plage de températures allant de −196 °C à +250 °C.
Le présent document ne s'applique pas à la pression externe.

Industrija za predelavo nafte in zemeljskega plina - Kompaktni prirobnični konektorji s tesnilnim obročem IX (ISO 27509:2020)

General Information

Status
Published
Publication Date
15-Dec-2020
Withdrawal Date
29-Jun-2021
ICS
23.040.60 - Flanges, couplings and joints
Technical Committee
CEN/TC 12 - Materials, equipment and offshore structures for petroleum and natural gas industries
Drafting Committee
CEN/TC 12 - Materials, equipment and offshore structures for petroleum and natural gas industries
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
16-Dec-2020
Completion Date
16-Dec-2020
Ref Project
SIST EN ISO 27509:2021 - Petroleum and natural gas industries - Compact flanged connections with IX seal ring (ISO 27509:2020)

Relations

Replaces
EN ISO 27509:2012/AC:2013 - Petroleum and natural gas industries - Compact flanged connections with IX seal ring - Technical Corrigendum 1 (ISO 27509:2012/Cor 1:2013)
Effective Date
23-Dec-2020
Replaces
EN ISO 27509:2012 - Petroleum and natural gas industries - Compact flanged connections with IX seal ring (ISO 27509:2012)
Effective Date
23-Dec-2020

Buy Standard

EN ISO 27509:2021EN ISO 27509:2021
PreviousNext
Standard
EN ISO 27509:2021
English language
116 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-februar-2021
Nadomešča:
SIST EN ISO 27509:2014
SIST EN ISO 27509:2014/AC:2014
Industrija za predelavo nafte in zemeljskega plina - Kompaktni prirobnični
konektorji s tesnilnim obročem IX (ISO 27509:2020)
Petroleum and natural gas industries - Compact flanged connections with IX seal ring
(ISO 27509:2020)
Erdöl- und Erdgasindustrie - Kompakte Flanschverbindungen mit IX Dichtungsring (ISO
27509:2020)
Industries du pétrole et du gaz naturel - Raccordements à brides compactes avec bague
d'étanchéité IX (ISO 27509:2020)
Ta slovenski standard je istoveten z: EN ISO 27509:2020
ICS:
23.040.60 Prirobnice, oglavki in spojni Flanges, couplings and joints
elementi
75.180.01 Oprema za industrijo nafte in Equipment for petroleum and
zemeljskega plina na splošno natural gas industries in
general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 27509
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2020
EUROPÄISCHE NORM
ICS 23.040.60 Supersedes EN ISO 27509:2012
English Version
Petroleum and natural gas industries - Compact flanged
connections with IX seal ring (ISO 27509:2020)
Industries du pétrole et du gaz naturel - Erdöl- und Erdgasindustrie - Kompakte
Raccordements à brides compactes avec bague Flanschverbindungen mit IX Dichtungsring (ISO
d'étanchéité IX (ISO 27509:2020) 27509:2020)
This European Standard was approved by CEN on 12 February 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 27509:2020 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 27509:2020) has been prepared by Technical Committee ISO/TC 67 "Materials,
equipment and offshore structures for petroleum, petrochemical and natural gas industries" in
collaboration with Technical Committee CEN/TC 12 “Materials, equipment and offshore structures for
petroleum, petrochemical and natural gas industries” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2021, and conflicting national standards shall be
withdrawn at the latest by June 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 27509:2012.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 27509:2020 has been approved by CEN as EN ISO 27509:2020 without any modification.

INTERNATIONAL ISO
STANDARD 27509
Second edition
2020-12
Petroleum and natural gas
industries — Compact flanged
connections with IX seal ring
Industries du pétrole et du gaz naturel — Raccordements à brides
compactes avec bague d'étanchéité IX
Reference number
ISO 27509:2020(E)
©
ISO 2020
ISO 27509:2020(E)
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

ISO 27509:2020(E)
Contents Page
Foreword .v
Introduction .vii
1 Scope . 1
2 Normative references . 1
3  Terms and definitions . 2
4 Abbreviations and symbols . 2
4.1 Abbreviated terms . 2
4.2 Symbols . 3
5 Design . 5
5.1 General . 5
5.2 Design principles . 6
5.3 Assembly requirements . 8
5.4 Standard components . 8
5.5 Units of measurements . 9
5.6 Rounding . 9
5.7 Conformance with piping design codes . 9
5.8 Conformance with this document .10
6 Designation .10
6.1 Designation of flanges .10
6.2 Designation of seal rings .10
7 Materials .11
7.1 General .11
7.2 Flange materials.11
7.3 Bolting materials .11
7.4 Seal ring materials .12
8 Strength, pressure/temperature ratings and leak tightness .13
8.1 General .13
8.2 Pressure/temperature ratings .13
8.3 Pressure testing and leak tightness .14
9  Dimensions of flanges .14
9.1 General .14
9.2 Weld neck dimensions .15
9.3 Blind flange (BL) dimensions .23
9.4 Integral flange (IF) dimensions .26
9.5 Rigid interface dimensions .37
9.6 Dimensions of paddle blanks (PB) and paddle spacers (PS) .39
9.7 Handle and lifting lugs .41
9.8 Dimensions of orifice spacers (OS) .42
9.9 Dimensions of reducing threaded flanges .44
9.10 Auxiliary connections .45
9.11 Flange tolerances .45
9.12 Surface finish .47
10  Marking of flanges.48
10.1 Flanges other than integral flanges .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 14870-3:2006(Main)
Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 3: Flanges (ISO 15590-3:2004, modified)
SIST EN 14870-3:2006

This part of EN 14870 applies to weldneck and blind flanges (full face, raised face, and RTJ groove) as well as anchor, swivel-ring flanges and orifice flanges.
This part of EN 14870 specifies the technical requirements for carbon steel and low-alloy steel forged flanges for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623.
This part of EN 14870 designates those categories of flanges that meet the industry's need to match ISO 3183 pipe. These flanges are for normal and low-temperature service and include supplementary requirements where required for sour service.
Materials for, or the attachment of, factory-welded extensions, bolting materials, gaskets, slip-on flanges or flanged fittings are not covered by this part of EN 14870.
This part of EN 14870 is not applicable to integrally cast or forged flanges for valves, pumps or other equipment.
This part of EN 14870 does not cover the selection of the flange category or pressure class. Sizes and pressure classes listed in ISO 7005-1 and applicable to this part of EN 14870 are as follows:
-   DN 10 (NPS 1/2) to DN 1500 (NPS 60);
-   PN 20 (class 150), PN 50 (class 300), PN 100 (class 600), PN 150 (class 900), PN 250 (class 1500), PN 420 (class 2500).
On-land supply systems used by the gas supply industry are excluded from the scope of this document.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1591-1:2024(Main)
Flanges and their joints - Design rules for gasketed circular flange connections - Part 1: Calculation
SIST EN 1591-1:2024

This document defines a calculation method for bolted, gasketed, circular flange joints. Its purpose is to ensure structural integrity and control of leak tightness. It uses gasket parameters based on definitions and test methods specified in EN 13555:2014.
The calculation method is not applicable to joints with a metallic contact out of the sealing face or to joints whose rigidity varies appreciably across gasket width. For gaskets in incompressible materials, which permit large deformations, the results given by the calculation method can be excessively conservative (i.e. required bolting load too high, allowable pressure of the fluid too low, required flange thickness too large, etc.).

  • Standard
    79 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1092-2:2023(Main)
Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges
SIST EN 1092-2:2024

This document specifies requirements for circular flanges made from ductile, grey and malleable cast iron for DN 10 to DN 4000 and PN 2,5 to PN 100. See 4.1 and 4.2 for information regarding allowed DN and PN.
This document specifies the types of flanges and their facings, dimension and tolerances, bolt sizes, surface finish of jointing faces, marking, testing, quality assurance and materials together with associated pressure/temperature (p/T) ratings.

  • Standard
    61 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14525:2022(Main)
Ductile iron and steel wide tolerance couplings and flange adaptors for use with pipes of different materials: ductile iron, Grey iron, steel, PVC-U, PVC-O, PE, fibre-cement
SIST EN 14525:2022

This document specifies the requirements and associated test methods applicable to wide tolerance ductile iron and steel (restricted sizes for steel) couplings, stepped/reducing couplings and flange adaptors intended for use with pipe components made from a number of pipe materials (ductile iron, grey iron, PE in conformity with EN 12201-1 to EN 12201-5, PVC-U in conformity with EN ISO 1452-1 to EN ISO 1452-5, PVC-O in conformity with EN 17176-1 to EN 17176-5, steel, fibre-cement), for providing a leak tight seal over a wide range of pipe outside diameters:
-   to convey water (e.g. water intended for human consumption);
-   with or without pressure;
-   to be installed below or above ground, inside or outside buildings.
This document is not intended to cover sewerage or gas applications, where additional requirements may be necessary.
This document specifies requirements for materials, dimensions and tolerances, mechanical properties and standard coatings of products.
This document covers wide tolerance couplings, stepped/reducing couplings and flange adaptors:
-   manufactured with socketed or flanged ends;
-   supplied externally and internally coated;
-   suitable for pipes made from ductile iron in conformity with EN 545, grey iron, PE in conformity with EN 12201-1 to EN 12201-5, PVC-U in conformity with EN ISO 1452-1 to EN ISO 1452-5, PVC-O in conformity with EN 17176-1 tot EN 17176-5, steel, fibre-cement in a size range extending from DN 40 to DN 800, for an allowable operating pressure (PFA) up to 16 bar, for fluid temperatures between 0 °C and 25 °C excluding frost. For higher temperatures, (up to 45 °C for PVC-U and PVC-O or 40 °C for PE) the PFA is derated as given in EN ISO 1452 and EN 12201;
-   not intended for use in areas subjected to reaction to fire regulations.
NOTE 1   This does not preclude special arrangements for the products to be used at higher temperatures. Temperature limitations and pressure limitations are those coming from the PVC-U, PVC-O or PE pipes.
This document covers ductile iron couplings, stepped/reducing couplings and flange adaptors cast by any type of foundry process or manufactured by fabrication of cast components, as well as corresponding joints, in a size range extending from DN 40 to DN 800.
As long as no equivalent European Standard exists for steel accessories, this document also covers couplings and flange adaptors which are fabricated partly or entirely from steel as well as corresponding joints, in a size range extending from DN 600 to DN 800.
This document specifies requirements for materials, dimensions and tolerances, mechanical properties and standard coatings. It also gives minimum performance requirements for all components, including restrained and non-restrained flexible joints. Joint design and gasket shapes are outside the scope of this document.
NOTE 2   PFA can be limited depending on pipe materials effectively connected.
NOTE 3   In this document, if not specified, all pressures are relative gauge pressures, expressed in bars (100 kPa = 1 bar).

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1515-4:2021/AC:2022(Corrigendum)
Flanges and their joints - Bolting - Part 4: Selection of bolting for equipment subject to the Pressure Equipment Directive 2014/68/EU
SIST EN 1515-4:2021/AC:2022

This document is applicable to the selection of bolting for flanged joints on equipment subject to the Pressure Equipment Directive 2014/68/EU.
It specifies standards and additional requirements for dimensions, material properties and technical conditions of delivery for bolting.
NOTE 1   Washers are not within the scope of this document.
The selection is based on commonly used bolting. It covers common temperature ranges of the general service of flanges.
When selecting bolting according to this document it is essential to take into account environmental conditions and other parameters including type of fluids, corrosion hazards, sour service, low temperature brittle failure and relaxation at elevated temperatures.
The purpose of this document is to provide a selection of most commonly used bolting types and bolting material combinations.
It is not the intention to specify all possible applications but to give guidance on the most common applications. For example, application limits for material in the creep range are not explicitly covered in this document. Where material standard provides mechanical properties for the creep range respective reference is made in Table 3.
NOTE 2   Special services and ambient conditions may require the application of coatings. It is the purchaser’s option to decide on this. Depending on the coating used, a verification of the temperature ranges given in Table 3 and Table 4 may be required.
NOTE 3   In Annex B there are bolting types and bolting material combinations according to commonly used national standards other than those listed in Table 2, Table 3 and Table 4.

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 3459:2022(Main)
Plastic piping systems - Mechanical joints between fittings and pressure pipes - Test method for leaktightness under negative pressure (ISO 3459:2022)
SIST EN ISO 3459:2022

This document specifies two methods of testing for checking the leaktightness of assembled joints between mechanical fittings and plastic pressure pipes with diameters up to and including 63 mm. The test applies regardless of the design and material of the fitting used for jointing plastics pipe.
This test method is not applicable to fusion-welded joints.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 3501:2022(Main)
Plastics piping systems - Mechanical joints between fittings and pressure pipes - Test method for resistance to pull-out under constant longitudinal force (ISO 3501:2021)
SIST EN ISO 3501:2022

This document specifies a method for checking the ability of assembled uniaxial joints between fittings and plastic pressure pipes to withstand longitudinal tensile stresses. The test applies regardless of the design and material of the fitting used for jointing plastics pipe.
This test method is not applicable to fusion-welded joints.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19879:2021(Main)
Metallic tube connections for fluid power and general use - Test methods for hydraulic fluid power connections (ISO 19879:2021)
SIST EN ISO 19879:2021

This document specifies uniform methods for the testing and performance evaluation of metallic tube connections, stud ends for ports and flange connections for use in hydraulic fluid power applications. This document does not apply to the testing of hydraulic quick-action couplings, which is covered by ISO 18869.
Tests outlined in this document are independent of each other and document the method to follow for each test. See the appropriate component International Standard for indications of which tests to conduct and for performance criteria.
For qualification of the connector, the minimum number of samples specified in this document is tested, unless otherwise specified in the relevant connector standard or as agreed upon by the manufacturer and the user.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1515-4:2021(Main)
Flanges and their joints - Bolting - Part 4: Selection of bolting for equipment subject to the Pressure Equipment Directive 2014/68/EU
SIST EN 1515-4:2021

This document is applicable to the selection of bolting for flanged joints on equipment subject to the Pressure Equipment Directive 2014/68/EU.
It specifies standards and additional requirements for dimensions, material properties and technical conditions of delivery for bolting.
NOTE 1   Washers are not within the scope of this document.
The selection is based on commonly used bolting. It covers common temperature ranges of the general service of flanges.
When selecting bolting according to this document it is essential to take into account environmental conditions and other parameters including type of fluids, corrosion hazards, sour service, low temperature brittle failure and relaxation at elevated temperatures.
The purpose of this document is to provide a selection of most commonly used bolting types and bolting material combinations.
It is not the intention to specify all possible applications but to give guidance on the most common applications. For example, application limits for material in the creep range are not explicitly covered in this document. Where material standard provides mechanical properties for the creep range respective reference is made in Table 3.
NOTE 2   Special services and ambient conditions may require the application of coatings. It is the purchaser’s option to decide on this. Depending on the coating used, a verification of the temperature ranges given in Table 3 and Table 4 may be required.
NOTE 3   In Annex B there are bolting types and bolting material combinations according to commonly used national standards other than those listed in Table 2, Table 3 and Table 4.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13555:2021(Main)
Flanges and their joints - Gasket parameters and test procedures relevant to the design rules for gasketed circular flange connections
SIST EN 13555:2021

This document specifies the gasket parameters required by EN 1591-1 and provides the test procedures for establishing the values of these parameters.
Gaskets which are wholly based upon elastomers, or based upon elastomers with only the inclusion of particulate fillers or particulate reinforcement, as opposed to gaskets combining elastomers, fillers and fibrous reinforcement, are beyond the scope of this document.
NOTE The testing procedures given might be applicable to gaskets of other shapes and dimensions.

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day