EN ISO 17658:2015
(Main)Welding - Imperfections in oxyfuel flame cuts, laser beam cuts and plasma cuts - Terminology (ISO 17658:2002)
Welding - Imperfections in oxyfuel flame cuts, laser beam cuts and plasma cuts - Terminology (ISO 17658:2002)
This international Standard defines terms of the possible imperfections in oxyfuel gas, laser beam and plasma cuts in metallic materials which are collected and grouped. Imperfections are irregularities or deviations from the specified shape and location of cut. This international Standard only includes imperfections originating directly from oxyfuel gas, laser beam and plasma arc cutting; any adverse effects resulting from additional external stresses or strains are not considered. The type, shape and location of these imperfections are grouped together but conditions and causes of origin are not given. Information concerning the evaluation and consequences of the above mentioned imperfections is not given because this depends on the specific job requirements. The terms have been selected to characterize the principal imperfections mentioned, however, two or more may be found simultaneously. The grouping system used is not an evaluation of quality.
Schweißen - Unregelmäßigkeiten an Brennschnitten, Laserstrahlschnitten und Plasmaschnitten - Terminologie (ISO 17658:2002)
Soudage - Défauts des coupes exécutées par oxycoupage, coupage laser et coupage plasma - Terminologie (ISO 17658:2002)
La présente Norme internationale définit les termes des défauts éventuels des coupes exécutées par oxycoupage, coupage laser et coupage plasma de matériaux métalliques qui sont réunis et groupés. On appelle défauts des irrégularités ou des écarts par rapport à la forme et à l’emplacement spécifiés pour la coupe. La présente Norme internationale ne comprend que les défauts résultant directement du coupage oxy-gaz combustible, du coupage laser et du coupage plasma; tout défaut provoqué par des contraintes ou des sollicitations supplémentaires n’est pas pris en considération. Le type, la forme et l’emplacement de ces défauts sont regroupés ensemble, mais les conditions et les causes de leur origine ne sont pas données. Il n’est pas donné d’information concernant l’évaluation et les conséquences des défauts mentionnés, ces informations dépendant des exigences spécifiques de l’application. Les termes ont été choisis de manière à caractériser les principaux défauts; il est toutefois possible d’en rencontrer deux simultanément. Le système de groupement utilisé n’est pas une évaluation de la qualité.
Varjenje - Nepopolnosti pri plamenskem, laserskem in plazemskem rezanju - Terminologija (ISO 17658:2002)
Ta mednarodni standard določa pogoje morebitnih nepopolnosti pri plamenskem, laserskem in plazemskem rezanju kovinskih materialov, ki so zbrani in razvrščeni v skupine. Nepopolnosti so nepravilnosti ali odstopanja od določene oblike in mesta reza. Ta mednarodni standard zajema samo nepopolnosti, ki izvirajo neposredno iz plamenskega, laserskega in plazemskega obločnega rezanja. Kakršni koli škodljivi učinki, ki bi nastali zaradi dodatnih zunanjih obremenitev, niso upoštevani. Tipi, oblike in mesta teh nepopolnosti so združeni v skupine, vendar pogoji in vzroki, iz katerih izvirajo, niso podani. Informacije glede ovrednotenja in posledic zgoraj navedenih nepopolnosti niso podane, ker so odvisne od zahtev posameznega dela. Izrazi so bili izbrani za opis glavnih omenjenih nepopolnosti, vendar je mogoče najti dva ali več hkrati. Uporabljeni sistem razporejanja v skupine ni vrednotenje kakovosti.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 17658:2015
01-september-2015
1DGRPHãþD
SIST EN 12584:1999
Varjenje - Nepopolnosti pri plamenskem, laserskem in plazemskem rezanju -
Terminologija (ISO 17658:2002)
Welding - Imperfections in oxyfuel flame cuts, laser beam cuts and plasma cuts -
Terminology (ISO 17658:2002)
Schweißen - Unregelmäßigkeiten an Brennschnitten, Laserstrahlschnitten und
Plasmaschnitten - Terminologie (ISO 17658:2002)
Soudage - Défauts des coupes exécutées par oxycoupage, coupage laser et coupage
plasma - Terminologie (ISO 17658:2002)
Ta slovenski standard je istoveten z: EN ISO 17658:2015
ICS:
01.040.25 Izdelavna tehnika (Slovarji) Manufacturing engineering
(Vocabularies)
25.160.10 Varilni postopki in varjenje Welding processes
SIST EN ISO 17658:2015 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 17658:2015
---------------------- Page: 2 ----------------------
SIST EN ISO 17658:2015
EUROPEAN STANDARD
EN ISO 17658
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2015
ICS 01.040.25; 25.160.10 Supersedes EN 12584:1999
English Version
Welding - Imperfections in oxyfuel flame cuts, laser beam cuts
and plasma cuts - Terminology (ISO 17658:2002)
Soudage - Défauts des coupes exécutées par oxycoupage, Schweißen - Unregelmäßigkeiten an Brennschnitten,
coupage laser et coupage plasma - Terminologie (ISO Laserstrahlschnitten und Plasmaschnitten - Terminologie
17658:2002) (ISO 17658:2002)
This European Standard was approved by CEN on 24 April 2015.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 17658:2015 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 17658:2015
EN ISO 17658:2015 (E)
Contents
Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 17658:2015
EN ISO 17658:2015 (E)
Foreword
The text of ISO 17658:2002 has been prepared by Technical Committee ISO/TC 44 “Welding and allied
processes” of the International Organization for Standardization (ISO) and has been taken over as EN ISO
17658:2015 by Technical Committee CEN/TC 121 “Welding and allied processes” the secretariat of which is
held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2015, and conflicting national standards shall be withdrawn at
the latest by October 2015.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 12584:1999.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 17658:2002 has been approved by CEN as EN ISO 17658:2015 without any modification.
3
---------------------- Page: 5 ----------------------
SIS
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.