iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 14502-1:2010

(Main)

Cranes - Equipment for the lifting of persons - Part 1: Suspended baskets

Cranes - Equipment for the lifting of persons - Part 1: Suspended baskets

This European Standard applies to baskets suspended on cranes.
This European Standard does not cover the controls for the movement of the basket.
This European Standard is not applicable to:
-   lifts for crane drivers;
-   moveable cabins.
This European Standard deals with all significant hazards, hazardous situations and events relevant to suspended baskets, when used as intended and under conditions foreseen by the manufacturer (see Clause 4).
The significant hazards covered by this document are identified in Clause 4.
This European Standard is not applicable to suspended baskets which are manufactured before the date of publication by CEN.

Krane - Einrichtungen zum Heben von Personen - Teil 1: Hängende Personenaufnahmemittel

Diese Europäische Norm gilt für hängende Personenaufnahmemittel, die an Kranen hängen.
Diese Europäische Norm behandelt nicht die Steuerungen für die Bewegungen des hängenden Personenaufnahmemittels.
Diese Europäische Norm gilt nicht für:
⎯ Aufzüge für Kranführer;
⎯ bewegliche Kabinen.
Diese Europäische Norm behandelt alle auf hängende Personenaufnahmemittel zutreffenden signifikanten
Gefährdungen, Gefährdungssituationen und Gefahr bringenden Ereignisse, sofern diese hängenden Personenaufnahmemittel
bestimmungsgemäß und unter den vom Hersteller vorgesehenen Bedingungen verwendet
werden (siehe Abschnitt 4).
Die in diesem Dokument behandelten signifikanten Gefährdungen sind in Abschnitt 4 identifiziert.
Diese Europäische Norm gilt nicht für hängende Personenaufnahmemittel, die vor dem Datum der Veröffentlichung
dieses Dokuments durch das CEN gebaut wurden.

Appareils de levage à charge suspendue - Equipements pour le levage de personnes - Partie 1: Nacelles suspendues

La présente Norme européenne s’applique aux nacelles suspendues sur des appareils de levage à charge suspendue.
La présente Norme européenne ne s’applique pas aux commandes des mouvements de la nacelle.
La présente Norme européenne ne s’applique pas :
-   aux ascenseurs destinés aux grutiers ;
-   aux cabines élevables.
La présente Norme européenne traite de tous les phénomènes dangereux significatifs, situations et évènements dangereux relatifs aux nacelles suspendues, lorsque celles-ci sont utilisées pour l’usage prévu et dans les conditions prévues par le fabricant (voir l’Article 4).
Les phénomènes dangereux significatifs traités dans la présente Norme européenne sont identifiés à l’Article 4.
La présente Norme européenne n’est pas applicable aux nacelles suspendues fabriquées avant sa date de publication par le CEN.

Dvigala (žerjavi) - Oprema za dvigovanje oseb - 1. del: Viseče košare

Ta evropski standard velja košare, ki visijo z žerjavov. Ta evropski standard ne zajema nadzornih elementov za premikanje košare. Ta evropski standard ne velja za: dvigala za voznike žerjavov; premične kabine. Ta evropski standard obravnava vse bistvene nevarnosti, nevarne situacije in primere, ki se nanašajo na viseče košare, kadar se uporabljajo v skladu z namembnostjo in pod pogoji, kot jih je predvidel proizvajalec (glej Klavzulo 4). Bistvene nevarnosti, zajete v tem dokumentu, so opredeljene v Klavzuli 4. Ta evropski standard ne velja za viseče košare, ki so bile izdelane pred datumom, ko je CEN standard objavil.

General Information

Status
Published
Publication Date
25-May-2010
ICS
53.020.30 - Accessories for lifting equipment
Technical Committee
CEN/TC 147 - Cranes - Safety
Drafting Committee
CEN/TC 147/WG 4 - Design - Requirements for health and safety
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
10-Jun-2022
Ref Project
SIST EN 14502-1:2010 - Cranes - Equipment for the lifting of persons - Part 1: Suspended baskets

Relations

Replaces
EN 14502-1:2005 - Cranes - Equipment for lifting persons - Part 1:Suspended baskets
Effective Date
22-May-2010

Buy Standard

EN 14502-1:2010EN 14502-1:2010
PreviousNext
Standard
EN 14502-1:2010
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.ãDUHKrane - Einrichtungen zum Heben von Personen - Teil 1: Hängende PersonenaufnahmemittelAppareils de levage à charge suspendue - Equipements pour le levage de personnes - Partie 1: Nacelles suspenduesCranes - Equipment for the lifting of persons - Part 1: Suspended baskets53.020.30Pribor za dvigalno opremoAccessories for lifting equipmentICS:Ta slovenski standard je istoveten z:EN 14502-1:2010SIST EN 14502-1:2010en,fr,de01-oktober-2010SIST EN 14502-1:2010SLOVENSKI
STANDARDSIST EN 14502-1:20051DGRPHãþD



SIST EN 14502-1:2010



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14502-1
May 2010 ICS 53.020.30 Supersedes EN 14502-1:2005English Version
Cranes - Equipment for the lifting of persons - Part 1: Suspended baskets
Appareils de levage à charge suspendue - Equipements pour le levage de personnes - Partie 1: Nacelles suspendues
Krane - Einrichtungen zum Heben von Personen - Teil 1: Hängende Personenaufnahmemittel This European Standard was approved by CEN on 16 April 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14502-1:2010: ESIST EN 14502-1:2010



EN 14502-1:2010 (E) 2 Contents Page Foreword .3Introduction .41Scope .52Normative references .53Terms and definitions .54List of significant hazards .65Safety requirements and/or protective measures .65.1General requirements .65.2Strength calculations .75.3Load lifting attachments .75.4Floor .95.5Inclination .95.6Side guarding . 105.7Access and exit . 115.8Anchorage for personal protective equipment against fall from a height . 116Verification of safety requirements and/or protective measures . 127Instruction manual . 127.1General .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 13001-3-5:2016+A1:2021(Main)
Cranes - General design - Part 3-5: Limit states and proof of competence of forged and cast hooks
SIST EN 13001-3-5:2016+A1:2021

This European Standard is to be used together with EN 13001-1 and EN 13001-2 and, as such, they specify general conditions, requirements and methods to prevent by design and theoretical verification, mechanical hazards in crane hooks.
This European Standard covers the following parts of hooks and types of hooks:
-   bodies of any type of hooks made of steel forgings;
-   machined shanks of hooks with a thread/nut suspension.
Principles of this European Standard can be applied to machined shanks of hooks in general. However, stress concentration factors relevant to designs not given in this standard would have to be determined and applied.
NOTE 1   Cast hooks and plate hooks, which are those, assembled of one or several parallel parts of rolled steel plates, are not covered in this European Standard.
The following is a list of significant hazardous situations and hazardous events that could result in risks to persons during normal use and foreseeable misuse. Clauses 4 to 8 of this document are necessary to reduce or eliminate the risks associated with the following hazards:
a)   exceeding the limits of strength (yield, ultimate, fatigue);
b)   exceeding temperature limits of material.
The requirements of this European Standard are stated in the main body of the document and are applicable to forged hook designs in general.
The commonly used hook body and shank designs listed in Annexes A, B and F are only examples and should not be referred to as requirements of this European Standard. Annex I gives guidance for the selection of a hook size, where a hook body is in accordance with Annex A or B. The selection of hook form is not limited to those shown in Annexes A and B.
This European Standard is applicable to cranes, which are manufactured after the date of approval of this European Standard by CEN, and serves as a reference base for product standards of particular crane types.
NOTE 2   This part of EN 13001 deals only with the limit state method in accordance with EN 13001-1.
FprA1:
Add after 1st paragraph the following sentence:
"
It has to be used together with the other generic parts of EN 13001 series of standards, see Annex L.
".
Replace in 2nd paragraph the 1st list item with:
"
-   bodies of any type of hooks made of steel forgings or steel castings, including stainless steel;".
Replace NOTE 1 with:
"
NOTE 1   Plate hooks, which are those, assembled of one or several parallel parts of rolled steel plates, are not covered in this document.".
In the 4th paragraph, replace the 1st list item with:
"
a)   exceeding the limits of yield strength, ultimate strength, fatigue strength, brittle fracture;".
Replace the 5th paragraph with:
"The requirements of this document are stated in the main body of the document and are applicable to hook designs in general.".
After 4th paragraph, add the sentence:
"
The hazards covered by this document are identified by Annex M.
".

  • Standard
    92 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13155:2020(Main)
Crane - Safety - Non-fixed load lifting attachments
SIST EN 13155:2021

This document specifies safety requirements for the following non-fixed load lifting attachments for cranes, hoists and manually controlled load manipulating devices:
a)   plate clamps;
b)   vacuum lifters:
1)   self-priming;
2)   non-self-priming (pump, venturi, turbine);
c)   lifting magnets:
1)   electric lifting magnets (battery fed and mains-fed);
2)   permanent lifting magnets;
3)   electro-permanent lifting magnets;
d)   lifting beams;
e)   C-hooks;
f)   lifting forks;
g)   clamps;
h)   lifting insert systems for use in normal weight concrete,
as defined in Clause 3.
This document does not give requirements for:
-   non-fixed load lifting attachments in direct contact with foodstuffs or pharmaceuticals requiring a high level of cleanliness for hygiene reasons;
-   hazards resulting from handling specific hazardous materials (e.g. explosives, hot molten masses, radiating materials);
-   hazards caused by operation in an explosive atmosphere;
-   hazards caused by noise;
-   hazards relating to the lifting of persons;
-   electrical hazards;
-   hazards due to hydraulic and pneumatic components.
For high risk applications not covered by this standard, EN 13001-2:2014, 4.3.2 gives guidance to deal with them.
This document covers the proof of static strength, the elastic stability and the proof of fatigue strength.
This document does not generally applies to attachments intended to lift above people. Some attachments are suitable for that purpose if equipped with additional safety features. In such cases the additional safety features are specified in the specific requirements.
This document does not cover slings, ladles, expanding mandrels, buckets, grabs, or grab buckets. This document does not cover power operated container handling spreaders, which are in the scope of EN 15056.
This document is not applicable to non-fixed load attachments manufactured before the date of its publication.

  • Standard
    112 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13155:2020/prA1(Amendment)
Cranes - Safety - Non-fixed load lifting attachments
SIST EN 13155:2021/oprA1:2023

This document specifies safety requirements for the following non-fixed load lifting attachments for cranes, hoists and manually controlled load manipulating devices:
a)   plate clamps;
b)   vacuum lifters:
1)   self-priming;
2)   non-self-priming (pump, venturi, turbine);
c)   lifting magnets:
1)   electric lifting magnets (battery fed and mains-fed);
2)   permanent lifting magnets;
3)   electro-permanent lifting magnets;
d)   lifting beams;
e)   C-hooks;
f)   lifting forks;
g)   clamps;
h)   lifting insert systems for use in normal weight concrete,
as defined in Clause 3.
This document does not give requirements for:
-   non-fixed load lifting attachments in direct contact with foodstuffs or pharmaceuticals requiring a high level of cleanliness for hygiene reasons;
-   hazards resulting from handling specific hazardous materials (e.g. explosives, hot molten masses, radiating materials);
-   hazards caused by operation in an explosive atmosphere;
-   hazards caused by noise;
-   hazards relating to the lifting of persons;
-   electrical hazards;
-   hazards due to hydraulic and pneumatic components.
For high risk applications not covered by this standard, EN 13001-2:2014, 4.3.2 gives guidance to deal with them.
This document covers the proof of static strength, the elastic stability and the proof of fatigue strength.
This document does not generally applies to attachments intended to lift above people. Some attachments are suitable for that purpose if equipped with additional safety features. In such cases the additional safety features are specified in the specific requirements.
This document does not cover slings, ladles, expanding mandrels, buckets, grabs, or grab buckets. This document does not cover power operated container handling spreaders, which are in the scope of EN 15056.
This document is not applicable to non-fixed load attachments manufactured before the date of its publication.
1   Modification to Clause 1, "Scope"
2nd paragraph after list, replace the reference to EN 13001-2:2014 with:
"EN 13001-2:2021".

  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13001-3-5:2016/FprA1(Amendment)
Cranes - General design - Part 3-5: Limit states and proof of competence of forged and cast hooks
SIST EN 13001-3-5:2016/kFprA1:2019

This European Standard is to be used together with EN 13001-1 and EN 13001-2 and, as such, they specify general conditions, requirements and methods to prevent by design and theoretical verification, mechanical hazards in crane hooks.
This European Standard covers the following parts of hooks and types of hooks:
-   bodies of any type of hooks made of steel forgings;
-   machined shanks of hooks with a thread/nut suspension.
Principles of this European Standard can be applied to machined shanks of hooks in general. However, stress concentration factors relevant to designs not given in this standard would have to be determined and applied.
NOTE 1   Cast hooks and plate hooks, which are those, assembled of one or several parallel parts of rolled steel plates, are not covered in this European Standard.
The following is a list of significant hazardous situations and hazardous events that could result in risks to persons during normal use and foreseeable misuse. Clauses 4 to 8 of this document are necessary to reduce or eliminate the risks associated with the following hazards:
a)   exceeding the limits of strength (yield, ultimate, fatigue);
b)   exceeding temperature limits of material.
The requirements of this European Standard are stated in the main body of the document and are applicable to forged hook designs in general.
The commonly used hook body and shank designs listed in Annexes A, B and F are only examples and should not be referred to as requirements of this European Standard. Annex I gives guidance for the selection of a hook size, where a hook body is in accordance with Annex A or B. The selection of hook form is not limited to those shown in Annexes A and B.
This European Standard is applicable to cranes, which are manufactured after the date of approval of this European Standard by CEN, and serves as a reference base for product standards of particular crane types.
NOTE 2   This part of EN 13001 deals only with the limit state method in accordance with EN 13001-1.
FprA1:
Add after 1st paragraph the following sentence:
"
It has to be used together with the other generic parts of EN 13001 series of standards, see Annex L.
".
Replace in 2nd paragraph the 1st list item with:
"
-   bodies of any type of hooks made of steel forgings or steel castings, including stainless steel;".
Replace NOTE 1 with:
"
NOTE 1   Plate hooks, which are those, assembled of one or several parallel parts of rolled steel plates, are not covered in this document.".
In the 4th paragraph, replace the 1st list item with:
"
a)   exceeding the limits of yield strength, ultimate strength, fatigue strength, brittle fracture;".
Replace the 5th paragraph with:
"The requirements of this document are stated in the main body of the document and are applicable to hook designs in general.".
After 4th paragraph, add the sentence:
"
The hazards covered by this document are identified by Annex M.
".

  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 13155 rev(Main)
Crane - Safety - Non-fixed load lifting attachments
oSIST prEN 13155:2011

To revise the standard to include non-fixed lifting attachments used during drilling operations.

  • Draft
    77 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN 13155 rev(Main)
Crane - Safety - Non-fixed load lifting attachments
oSIST prEN 13155:2014

To revise the standard to include non-fixed lifting attachments used during drilling operations.

  • Draft
    69 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13411-3:2022(Main)
Terminations for steel wire ropes - Safety - Part 3: Ferrules and ferrule-securing
SIST EN 13411-3:2023

This document deals with the requirements for the ferrule-securing of eyes and endless loops.
It also deals with the requirements for ferrules for the ferrule-securing of eyes and endless loops.
This document applies to the ferrule-securing of eye terminations formed either by a Flemish eye or turn-back eye and covers ferrules made of non-alloy carbon steel and aluminium.
This document applies to slings and assemblies using steel wire ropes for general lifting applications up to and including 60 mm diameter conforming to EN 12385-4, lift ropes conforming to EN 12385-5 and spiral strand ropes conforming to EN 12385-10.
Type testing of ferrule-secured systems and manufacturing quality control requirements are also specified.
This document deals with all significant hazards, hazardous situations, and events relevant to this particular steel wire rope termination when used as intended and under conditions of use which are foreseeable by the manufacturer.
This document applies to terminations of steel wire ropes with ferrules and ferrule-securing which are manufactured after the date of this publication.
NOTE   One design of ferrule-secured turn-back eye termination using an oval aluminium ferule which satisfies the requirements of this document when securing ropes having rope grades up to and including 1960 is given for information in Annex A.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13411-7:2021(Main)
Terminations for steel wire ropes - Safety - Part 7: Symmetric wedge socket
SIST EN 13411-7:2021

This document specifies the minimum requirements for symmetrical wedge socket terminations for stranded steel wire ropes conforming to EN 12385-5 for lifts.
This document covers those symmetric wedge sockets intended for use at temperatures between −20 °C and 100 °C.
This document only covers those symmetric wedge sockets that have welded socket bodies. An example of the construction and sizes of a symmetric wedge socket is given in informative Annex A.
The informative Annex B gives the recommendations for the safe use and inspection of symmetric wedge socket according to Annex A.
This document deals with all significant hazards, hazardous situations and events relevant to symmetric wedge sockets for terminations for steel wire ropes, when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
The hazards covered by this document are identified in Clause 4.
This document applies to symmetric wedge sockets, which are manufactured after the date of its publication.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13001-3-5:2016+A1:2021(Main)
Cranes - General design - Part 3-5: Limit states and proof of competence of forged and cast hooks
SIST EN 13001-3-5:2016+A1:2021

This European Standard is to be used together with EN 13001-1 and EN 13001-2 and, as such, they specify general conditions, requirements and methods to prevent by design and theoretical verification, mechanical hazards in crane hooks.
This European Standard covers the following parts of hooks and types of hooks:
-   bodies of any type of hooks made of steel forgings;
-   machined shanks of hooks with a thread/nut suspension.
Principles of this European Standard can be applied to machined shanks of hooks in general. However, stress concentration factors relevant to designs not given in this standard would have to be determined and applied.
NOTE 1   Cast hooks and plate hooks, which are those, assembled of one or several parallel parts of rolled steel plates, are not covered in this European Standard.
The following is a list of significant hazardous situations and hazardous events that could result in risks to persons during normal use and foreseeable misuse. Clauses 4 to 8 of this document are necessary to reduce or eliminate the risks associated with the following hazards:
a)   exceeding the limits of strength (yield, ultimate, fatigue);
b)   exceeding temperature limits of material.
The requirements of this European Standard are stated in the main body of the document and are applicable to forged hook designs in general.
The commonly used hook body and shank designs listed in Annexes A, B and F are only examples and should not be referred to as requirements of this European Standard. Annex I gives guidance for the selection of a hook size, where a hook body is in accordance with Annex A or B. The selection of hook form is not limited to those shown in Annexes A and B.
This European Standard is applicable to cranes, which are manufactured after the date of approval of this European Standard by CEN, and serves as a reference base for product standards of particular crane types.
NOTE 2   This part of EN 13001 deals only with the limit state method in accordance with EN 13001-1.
FprA1:
Add after 1st paragraph the following sentence:
"
It has to be used together with the other generic parts of EN 13001 series of standards, see Annex L.
".
Replace in 2nd paragraph the 1st list item with:
"
-   bodies of any type of hooks made of steel forgings or steel castings, including stainless steel;".
Replace NOTE 1 with:
"
NOTE 1   Plate hooks, which are those, assembled of one or several parallel parts of rolled steel plates, are not covered in this document.".
In the 4th paragraph, replace the 1st list item with:
"
a)   exceeding the limits of yield strength, ultimate strength, fatigue strength, brittle fracture;".
Replace the 5th paragraph with:
"The requirements of this document are stated in the main body of the document and are applicable to hook designs in general.".
After 4th paragraph, add the sentence:
"
The hazards covered by this document are identified by Annex M.
".

  • Standard
    92 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13411-9:2021(Main)
Terminations for steel wire ropes - Safety - Part 9: Solid thimbles
SIST EN 13411-9:2021

This document specifies the minimum requirements for solid thimbles made of steel or cast iron for terminations of stranded steel wire ropes.
This document is applicable to ferrule-secured terminations with solid thimbles in combination with ferrules (see EN 13411-3), that have an efficiency factor KT of at least 0,9, and to spliced terminations with solid thimbles (see EN 13411-2), that have an efficiency factor KT of at least 0,8, which are used as accessories for steel wire ropes, such as slings or wire rope assemblies, having a lifting, lowering or load-bearing effect in hoisting equipment.
Examples of designs of solid thimbles which meet the requirements of this standard are given in informative Annexes B and C.
Round thimbles (thimble with rotational symmetry around the bore) are not subject to this document.
This document is applicable to ferrule-secured terminations that are manufactured after the date of publication of this document.
Hazards that are dealt with in this document are listed in Clause 4.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day