EN 10028-5:2003

Flat products made of steels for pressure purposes - Part 5: Weldable fine grain steels, thermomechanically rolled

This part of EN 10028 specifies the requirements for flat products for pressure equipments made of themomechanically rolled steels as listed in table 1.  The steels are not suitable for hot forming.  NOTE: Until now insufficient data for the standardization of the elevated temperature properties of these steels are available. If their use at such temperatures is intended the conditions for this shall be especially agreed between the interested parties.  Other parts of this European Standard are:  EN 10028-1 Flat products made of steels for pressure purposes - General requirements  EN 10028-2 Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties  EN 10028-3 Flat producs made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized  EN 10028-4 Flat products made of steels for pressure purposes - Part 4: Nickel-alloy steels with specified low temperature properties  EN 10028-6 Flat products made of steels for pressure purposes - Part 6: Weldable fine grain steels, quenched and tempered  EN 10028-7 Flat products made of steels for pressure purposes - Part 7: Stainless steels.

Flacherzeugnisse aus Druckbehälterstählen - Teil 5: Schweißgeeignete Feinkornbaustähle, thermomechanisch gewalzt

Produits plats en aciers pour appareils à pression - Partie 5: Aciers soudables à grains fins, laminés thermomécaniquement

Ploščati jekleni izdelki za tlačne posode – 5. del: Variva drobnozrnata jekla, toplotnomehansko valjana

General Information

• Status: Withdrawn
• Publication Date: 17-Jun-2003
• Withdrawal Date: 16-Jun-2009
• ICS: 77.140.30 - Steels for pressure purposes
• ICS: 77.140.50 - Flat steel products and semi-products
• Technical Committee: ECISS/TC 107 - Steels for pressure purposes
• Drafting Committee: ECISS/TC 107 - Steels for pressure purposes
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 17-Jun-2009
• Completion Date: 17-Jun-2009
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Ref Project: SIST EN 10028-5:2003 - Flat products made of steels for pressure purposes - Part 5: Weldable fine grain steels, thermomechanically rolled

Relations

• Replaces: EN 10028-5:1996 - Flat products made of steels for pressure purposes - Part 5: Weldable fine grain steels, thermomechanically rolled
• Effective Date: 22-Dec-2008
• Replaced By: EN 10028-5:2009 - Flat products made of steels for pressure purposes - Part 5: Weldable fine grain steels, thermomechanically rolled
• Effective Date: 22-Dec-2008

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Flat products made of steels for pressure purposes - Part 5: Weldable fine grain steels, thermomechanically rolledProduits plats en aciers pour appareils a pression - Partie 5: Aciers soudables a grains fins, laminés thermomécaniquementFlacherzeugnisse aus Druckbehälterstählen - Teil 5: Schweißgeeignete Feinkornbaustähle, thermomechanisch gewalztTa slovenski standard je istoveten z:EN 10028-5:2003SIST EN 10028-5:2003en77.140.5077.140.30ICS:SIST EN 10028-5:19971DGRPHãþDSLOVENSKI
STANDARDSIST EN 10028-5:200301-november-2003







EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10028-5June 2003ICS 77.140.30; 77.140.50Supersedes EN 10028-5:1996English versionFlat products made of steels for pressure purposes - Part 5:Weldable fine grain steels, thermomechanically rolledProduits plats en aciers pour appareils à pression - Partie5: Aciers soudables à grains fins, laminésthermomécaniquementFlacherzeugnisse aus Druckbehälterstählen - Teil 5:Schweißgeeignete Feinkornbaustähle, thermomechanischgewalztThis European Standard was approved by CEN on 17 January 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10028-5:2003 E



EN 10028-5:2003 (E)2Contents pageForeword.31Scope.42Normative references.43Terms and definitions.44Dimension and tolerances.45Calculation of mass.46Classification and designation.46.1Classification.46.2Designation.57Information to be supplied by the purchaser.57.1Mandatory information.57.2Options.57.3Example for ordering.58Requirements.58.1Steelmaking process.58.2Delivery condition.58.3Chemical composition.
...