iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 5774:2016

(Main)

Plastics hoses - Textile-reinforced types for compressed-air applications - Specification (ISO 5774:2016)

Plastics hoses - Textile-reinforced types for compressed-air applications - Specification (ISO 5774:2016)

ISO 5774:2016 specifies the requirements for four types of flexible thermoplastic hose, textile reinforced, for compressed-air applications in the temperature range from −10 °C to +60 °C.
The four types are classified as light service for a maximum working pressure of 7 bar at 23 °C and 4,5 bar at 60 °C, medium service for a maximum working pressure of 10 bar at 23 °C and 6,5 bar at 60 °C, heavy service for a maximum working pressure of 16 bar at 23 °C and 11 bar at 60 °C, and heavy service for use in mining for a maximum working pressure of 25 bar at 23 °C and 13 bar at 60 °C.

Kunststoffschläuche - Textilverstärkte Typen für Druckluftanwendungen - Anforderung (ISO 5774:2016)

Diese Internationale Norm legt die Anforderungen an vier Typen von flexiblen thermoplastischen Schläuchen mit Textileinlage für Druckluftanwendungen in einem Temperaturbereich von -10 °C bis +60 °C fest.
Die vier Typen werden eingestuft in einen leichten Einsatzbereich mit einem maximalen Betriebsdruck von 7 bar bei 23 °C und 4,5 bar bei 60 °C, einen mittleren Einsatzbereich mit einem maximalen Betriebsdruck von 10 bar bei 23 °C und 6,5 bar bei 60 °C, einen schweren Einsatzbereich mit einem maximalen Betriebsdruck von 16 bar bei 23 °C und 11 bar bei 60 °C und einen schweren Einsatzbereich zur Anwendung im Bergbau mit einem maximalen Betriebsdruck von 25 bar bei 23 °C und 13 bar bei 60 °C.

Tuyaux en plastique - Types armés de textile pour applications avec de l'air comprimé - Spécifications (ISO 5774:2016)

ISO 5774:2016 spécifie les exigences relatives à quatre types de tuyaux souples en thermoplastique, armés de textile, destinés aux applications d'air comprimé dans la plage de températures de −10 °C to +60 °C.
Les quatre types sont classés comme suit: service léger pour une pression maximale de service de 7 bar à 23 °C et de 4,5 bar à 60 °C, service moyen pour une pression maximale de service de 10 bar à 23 °C et de 6,5 bar à 60 °C, service intensif pour une pression maximale de service de 16 bar à 23 °C et de 11 bar à 60 °C, et service intensif dans les mines pour une pression maximale de service de 25 bar à 23 °C et de 13 bar à 60 °C.

Polimerne cevi - S tekstilom ojačene cevi za zrak pod tlakom - Specifikacija (ISO 5774:2016)

Ta mednarodni standard določa zahteve za štiri tipe s tekstilom ojačenih cevi iz plastomerov za zrak pod tlakom v temperaturnem razponu od −10 do 60 °C. Štirje tipi so razvrščeni kot majhna obremenitev za delovni tlak 7 barov pri 23 °C in 4,5 bara pri 60 °C, srednja obremenitev za največji delovni tlak 10 barov pri 23 °C in 6,5 bara pri 60 °C, velika obremenitev za največji delovni tlak 16 barov pri 23 °C in 11 barov pri 60 °C ter velika obremenitev za uporabo v rudarstvu za največji delovni tlak 25 barov pri 23 °C in 13 barov pri 60 °C.

General Information

Status
Withdrawn
Publication Date
23-Feb-2016
Withdrawal Date
02-May-2023
ICS
23.040.70 - Hoses and hose assemblies
Technical Committee
CEN/TC 218 - Rubber and plastics hoses and hose assemblies
Drafting Committee
CEN/TC 218 - Rubber and plastics hoses and hose assemblies
Current Stage
Ref Project
SIST EN ISO 5774:2016 - Plastics hoses - Textile-reinforced types for compressed-air applications - Specification (ISO 5774:2016)

Relations

Replaces
EN ISO 5774:2008 - Plastics hoses - Textile-reinforced types for compressed-air applications - Specification (ISO 5774:2006)
Effective Date
02-Mar-2016
Replaced By
EN ISO 5774:2023 - Plastics hoses - Textile-reinforced types for compressed-air applications - Specification (ISO 5774:2023)
Effective Date
18-Jan-2023

Buy Standard

EN ISO 5774:2016EN ISO 5774:2016
PreviousNext
Standard
EN ISO 5774:2016
English language
21 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 5774:2016
01-april-2016
1DGRPHãþD
SIST EN ISO 5774:2009
3ROLPHUQHFHYL6WHNVWLORPRMDþHQHFHYL]D]UDNSRGWODNRP6SHFLILNDFLMD ,62

Plastics hoses - Textile-reinforced types for compressed-air applications - Specification
(ISO 5774:2016)
Kunststoffschläuche - Textilverstärkte Typen für Druckluftanwendungen - Anforderung
(ISO 5774:2016)
Tuyaux en plastique - Types armés de textile pour applications avec de l'air comprimé -
Spécifications (ISO 5774:2016)
Ta slovenski standard je istoveten z: EN ISO 5774:2016
ICS:
83.140.40 Gumene cevi Hoses
SIST EN ISO 5774:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 5774:2016

---------------------- Page: 2 ----------------------

SIST EN ISO 5774:2016


EN ISO 5774
EUROPEAN STANDARD

NORME EUROPÉENNE

February 2016
EUROPÄISCHE NORM
ICS 23.040.70 Supersedes EN ISO 5774:2008
English Version

Plastics hoses - Textile-reinforced types for compressed-
air applications - Specification (ISO 5774:2016)
Tuyaux en plastique - Types armés de textile pour Kunststoffschläuche - Textilverstärkte Typen für
applications avec de l'air comprimé - Spécifications Druckluftanwendungen - Anforderung (ISO
(ISO 5774:2016) 5774:2016)
This European Standard was approved by CEN on 21 November 2015.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 5774:2016 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 5774:2016
EN ISO 5774:2016 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 5774:2016
EN ISO 5774:2016 (E)
European foreword
This document (EN ISO 5774:2016) has been prepared by Technical Committee ISO/TC 45 "Rubber and
rubber products" in collaboration with Technical Committee CEN/TC 218 “Rubber and plastics hoses
and hose assemblies” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2016, and conflicting national standards shall
be withdrawn at the latest by August 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 5774:2008.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 5774:2016 has been approved by CEN as EN ISO 5774:2016 without any modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 5774:2016

---------------------- Page: 6 ----------------------

SIST EN ISO 5774:2016
INTERNATIONAL ISO
STANDARD 5774
Fourth edition
2016-01-15
Plastics hoses — Textile-reinforced
types for compressed-air applications
— Speci
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 5774:2023(Main)
Plastics hoses - Textile-reinforced types for compressed-air applications - Specification (ISO 5774:2023)
SIST EN ISO 5774:2023

This document specifies the requirements for four types of flexible thermoplastic hose, textile reinforced, for compressed-air applications in the temperature range from −10 °C to +60 °C.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13483:2022(Main)
Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems - Specification
SIST EN 13483:2022

This document specifies the requirements and test methods for verification for hose assemblies with vapour recovery for delivery systems on petrol filling stations.
Hoses can be constructed from rubber or thermoplastic elastomer (TPE) and this document specifies the requirements for three types of hoses in two grades and two classes of hose assemblies for measured fuel dispensing systems, including oxygenated fuels (≤15 % oxygenated compounds) with internal vapour recovery tubing or hose made out of rubber or thermoplastic elastomer (TPE).
The assemblies are intended for use at ambient temperatures between -30 °C and +55 °C for normal temperature class and -40 °C and +55 °C for low temperature class at a working pressure ≤ 16 bar.
This document is not applicable to multi chamber fuel dispensing hoses.
NOTE As part of the certification of a new dispenser, testing of fuel samples in accordance with EN 228 is carried out at least eight weeks after the first use of the equipment to avoid unrepresentative sulphur content results.
1 bar = 0,1 MPa.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14420-2:2022(Main)
Hose fittings with clamp units - Part 2: Hose side parts of hose tail
SIST EN 14420-2:2022

This document specifies requirements for the hose tail of hose fittings according to EN 14420-1 for use with clamp units according to EN 14420-3. Furthermore, it specifies materials for hose fittings with clamp units according to EN 14420-4 to EN 14420-8.
Maximum working pressure is 25 bar ; maximum working temperature is 65 °C.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14420-4:2022(Main)
Hose fittings with clamp units - Part 4: Flange connections
SIST EN 14420-4:2022

This document specifies requirements for hose tails according to EN 14420-2, with flanges of mating dimensions PN 10/PN 16/PN 25/PN 40 (according to nominal size and pressure stage) according to EN 1092-1, on hose fittings with clamp units according to EN 14420-3.
Maximum working pressure is 25 bar; maximum working temperature is 65 °C.
Additionally, flanges are also usable according to EN 14422.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14420-7:2022(Main)
Hose fittings with clamp units - Part 7: Cam locking couplings
SIST EN 14420-7:2022

This document specifies the design, materials, dimensions and marking requirements for cam locking couplings that serve as the link between hoses and connections to transport liquids, solids and gases, except liquid gas and steam.
For all sizes of aluminium cast material couplings and for all couplings of size DN 100, the pressure range is from -0,8 bar to 10 bar in the working temperature range from -20 °C to +65 °C. All other couplings according to this document are capable of operating within the pressure range from 0,8 bar  to 16 bar in the working temperature range from -20 °C to +65 °C.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 8330:2022(Main)
Rubber and plastics hoses and hose assemblies - Vocabulary (ISO 8330:2022)
SIST EN ISO 8330:2022

This document defines terms used in the hose industry.
Recommended terminology for electrical conductivity and resistance of rubber and plastics hoses and hose assemblies can be found in ISO 8031:2020, Annex A.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 18752:2022(Main)
Rubber hoses and hose assemblies - Wire- or textile-reinforced single-pressure types for hydraulic applications - Specification (ISO 18752:2022)
SIST EN ISO 18752:2022

This document specifies requirements for ten classes, four grades and seven types of wire- or textile-reinforced hydraulic hoses and hose assemblies of nominal sizes ranging from 5 to 102. Each class has a single maximum working pressure for all sizes.
They are suitable for use with:
—    oil-based hydraulic fluids HH, HL, HM, HR and HV as defined in ISO 6743‑4 at temperatures ranging from −40 °C to +100 °C for types AS, AC, BS and BC hoses and from −40 °C to +120 °C for types CS, CC and DC hoses.
—    water-based fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743‑4 at temperatures ranging from −40 °C to +70 °C.
—    water at temperatures ranging from 0 °C to +70 °C.
This document does not include requirements for the connection ends. It is limited to the performance of hoses and hose assemblies. The hose assembly maximum working pressure is governed by the lowest maximum working pressure of the components.
NOTE       It is the responsibility of the user, in consultation with the hose manufacturer, to establish the compatibility of the hose with the fluid to be used.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 4671:2022(Main)
Rubber and plastics hoses and hose assemblies - Methods of measurement of the dimensions of hoses and the lengths of hose assemblies (ISO 4671:2022)
SIST EN ISO 4671:2022

This document specifies methods of measuring the inside diameter, outside diameter (including diameter over reinforcement of hydraulic hoses), wall thickness, concentricity and lining and cover thickness of hoses, methods of measurement and identification of the lengths of hoses and hose assemblies, and a method of verifying the through-bore of hydraulic hose assemblies.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 6801:2021(Main)
Rubber and plastics hoses - Determination of volumetric expansion (ISO 6801:2021)
SIST EN ISO 6801:2022

This document specifies a method for the determination of the volumetric expansion of rubber or plastics hoses under hydrostatic pressure.
This document does not specify the dimensions of the test piece and the test pressure(s) as each of which is specified in the appropriate specification.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 10619-2:2021(Main)
Rubber and plastics hoses and tubing - Measurement of flexibility and stiffness - Part 2: Bending tests at sub-ambient temperatures (ISO 10619-2:2021)
SIST EN ISO 10619-2:2021

This document specifies two methods for measuring the stiffness and one method for the determination of the flexibility of rubber and plastics hoses and tubing when they are bent to a specific radius at sub-ambient temperatures.
Method A is suitable for non-collapsible rubber and plastics hoses and tubing with a bore of up to and including 25 mm. This method provides a means of measuring the stiffness of the hose or tubing when the temperature is reduced from a standard laboratory temperature.
Method B is suitable for rubber and plastics hoses and tubing with a bore of up to 100 mm and provides a means of assessing the flexibility of the hose or tubing when bent around a mandrel at a specified sub-ambient temperature. It can also be used as a routine quality control test.
Method C is suitable for rubber and plastics hoses and tubing with a bore of 100 mm and greater. This method provides a means of measuring the stiffness of the hose and tubing at sub-ambient temperatures. This method is only suitable for hoses and tubing which are non-collapsible.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day