EN ISO 527-2:1996

Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:1993 including Corr 1:1994)

The methods specified are selectively suitable for use with the following range of materials: rigid and semirigid thermoplastics moulding, extrusion and cast materials, including compounds filled and reinforced by e.g. short fibres, small rods, plates or granules but excluding textile fibres in addition to unfilled types, rigid and semirigid thermosetting moulding and cast naterials, including filled and reinforced compounds but excluding textile fibres as reinforcement, and thermotropic liquid crystal polymers.

Kunststoffe - Bestimmung der Zugeigenschaften - Teil 2: Prüfbedingungen für Form- und Extrusionsmassen (ISO 527-2:1993 einschließlich Corr 1:1994)

1.1 Dieser Teil von ISO 527 legt auf der Basis der Grundsätze aus ISO 527-1 diePrüfbedingungen zur Bestimmung der Zugeigenschaften von Form- und Extrusionsmassen fest.

Plastiques - Détermination des propriétés en traction - Partie 2: Conditions d'essai des plastiques pour moulage et extrusion (ISO 527-2:1993 inclus Corr 1:1994)

1.1 La présente partie de l'ISO 527 prescrit des conditions d'essai pour la détermination des propriétés en traction des plastiques destinés au moulage et à l'extrusion, basées sur les principes généraux établis dans l'ISO 527-1. 1.2 La méthode convient sélectivement à l'utilisation de la gamme des matériaux suivants: -- matières thermoplastiques rigides et semi-rigides pour moulage, extrusion et coulée, y compris les compositions chargées et renforcées, par exemple de fibres courtes, fins bâtonnets, plaquettes ou granulés mais excluant les fibres textiles (voir ISO 527-4 et ISO 527-5); -- matières thermodurcissables rigides et semi-rigides pour moulage et coulée, y compris les compositions chargées et renforcées excluant les fibres textiles comme renforcement (voir ISO 527-4 et ISO 527-5); -- polymères de cristaux liquides thermotropes. Les méthodes ne conviennent pas à l'utilisation de matières renforcées de fibres textiles (voir ISO 527-4 et ISO 527-5), aux matériaux alvéolaires rigides ainsi qu'aux structures sandwichs contenant des matériaux alvéolaires. 1.3 Les méthodes sont adaptées à l'utilisation d'éprouvettes qui sont, soit moulées aux dimensions choisies, soit usinées, découpées ou poinçonnées à partir de plaques obtenues par injection ou par compression. L'éprouvette à usages multiples telle que décrite dans l'ISO 3167:1993, Plastiques -- 68Eprouvettes à usages multiples, est recommandée.

Polimerni materiali – Določevanje nateznih lastnosti – 2. del: Preskusni pogoji za polimerne materiale za oblikovanje in ekstrudiranje (ISO 527-2:1993, vključno s tehničnim popravkom 1:1994)

General Information

• Status: Withdrawn
• Publication Date: 21-May-1996
• Withdrawal Date: 14-Feb-2012
• ICS: 83.080.01 - Plastics in general
• Technical Committee: CEN/TC 249 - Plastics
• Drafting Committee: CEN/TC 249/SC 1/WG 3 - Mechanical properties and preparation of test specimens
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 15-Feb-2012
• Completion Date: 15-Feb-2012
• Ref Project: SIST EN ISO 527-2:1999 - Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:1993 including Technical Corr. 1:1994)

Relations

• Replaced By: EN ISO 527-2:2012 - Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012)
• Effective Date: 07-Mar-2012

Standards Content (Sample)

SLOVENSKI STANDARD
01-maj-1999
3ROLPHUQLPDWHULDOL±'RORþHYDQMHQDWH]QLKODVWQRVWL±GHO3UHVNXVQLSRJRML]D
SROLPHUQHPDWHULDOH]DREOLNRYDQMHLQHNVWUXGLUDQMH,62YNOMXþQRV
WHKQLþQLPSRSUDYNRP
Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and
extrusion plastics (ISO 527-2:1993 including Technical Corr. 1:1994)
Kunststoffe - Bestimmung der Zugeigenschaften - Teil 2: Prüfbedingungen für Form- und
Extrusionsmassen (ISO 527-2:1993 einschließlich Corr 1:1994)
Plastiques - Détermination des propriétés en traction - Partie 2: Conditions d'essai des
plastiques pour moulage et extrusion (ISO 527-2:1993 inclus Corr 1:1994)
Ta slovenski standard je istoveten z: EN ISO 527-2:1996
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

INTERNATIONAL IS0
STANDARD 527-2
First edith
1993-06-15
Plastics - Determination of tensile
properties -
Part 2:
Test conditions for moulding and extrusion
plastics
P/as tiques - D6termina tion des propri6 t& en traction -
Partie 2: Conditions d ’essai des plastiques pour moulage et extrusion
Reference number
IS0 5272:1993(E)
IS0 527=2:1993(E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide
federation of national standards bodies (IS0 member bodies). The work
of preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. IS0
collaborates closely with the International Electrotechnical Commission
(I EC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard IS0 527-2 was prepared by Technical Committee
lSO/TC 61, Plastics, Sub-Committee SC 2, Mechanical properties.
Together with the other parts of IS0 527, it cancels and replaces IS0
Recommendation R 527:1966, which has been technically revised.
Annex A of this part of IS0 527 cancels and replaces IS0 6239:1986,
P/as tics - Determination of tensile properties by use of small
specimens.
IS0 527 consists of the following parts, under the general title
P/as tics - Determination of tensile properties:
- Part I: General principles
- Part 2: Test conditions for moulding and extrusion plastics
- Part 3: Test conditions for sheet and film
- Part 4: Test conditions for isotropic and orthotropic fibre-reinforced
p/as tic composites
- Part 5: Test conditions for unidirectional fibre-reinforced plastic
composites
Annex A forms an integral part of this part of IS0 527.
0 IS0 1993
All rights reserved. No part of this publication may be reproduced or utilized in any form or
by any means, electronic or mechanical, including photocopying and microfilm, without per-
mission in writing from the publisher,
International Organization for Standardization
Case Postale 56 l CH-1211 Geneve 20 l Switzerland
Printed in Switzerland
ii
IS0 527=2:1993(E)
INTERNATIONAL STANDARD
Plastics - Determination of tensile properties -
Part 2:
Test conditions for moulding and extrusion plastics
1 Scope 2 Normative references
1.1 This part of IS0 527 specifies the test con-
ditions for determining the tensile properties of
moulding and extrusion plastics, based upon the gen-
The following standards contain provisions which,
eral principles given in IS0 527-l.
through reference in this text, constitute provisions
of this part of IS0 527. At the time of publication, the
editions indicated were valid. All standards are subject
to revision, and parties to agreements based on this
1.2 The methods are selectively suitable for use
part of IS0 527 are encouraged to investigate the
with the following range of materials:
possibility of applying the most recent editions of the
standards indicated below. Members of IEC and IS0
- rigid and semirigid thermoplastics moulding,
maintain registers of currently valid International
extrusion and cast materials, including compounds
Standards.
filled and reinforced by e.g. short fibres, small
rods, plates or granules but excluding textile fibres
IS0 3711977, Rubber, vulcanized - Determination of
(see IS0 527-4 and IS0 527-5) in addition to un-
filled types; tensile stress-s train properties.
- rigid and semirigid thermosetting moulding and IS0 293:1986, Plastics - Compression moulding test
cast materials, including filled and reinforced com- specimens of thermoplastic materials.
pounds but excluding textile fibres as reinforce-
IS0 294: -7)r P/as tics - Injection moulding of test
ment (see IS0 527-4 and IS0 527-5);
specimens of thermoplastic materials.
- thermotropic liquid crystal polymers.
IS0 295:1991, Plastics - Compression moulding of
The methods are not suitable for use with materials
test specimens of thermosetting materials.
reinforced by textile fibres (see IS0 527-4 and
IS0 527-5), with rigid cellular materials or sandwich
IS0 527-l :1993, Plastics - Determination of tensile
structures containing cellular material.
properties - Part I: General principles.
IS0 1926: 1979, Cellular plastics - Determination of
1.3 The methods are applied using specimens tensile properties of rigid materials.
which may be either moulded to the chosen dimen-
sions or machined, cut or punched from injection- or -*), P/as tics - Preparation of test speci-
IS0 2818:
compression-moulded plates. The multipurpose test
mens by machining.
specimen is preferred (see IS0 3167:1993, Plastics
- Multipurpose test specimens).
1) To be published. (Revision of IS0 294:1975)
2) To be published. (Revision of IS0 2818:1980)

IS0 527=2:1993(E)
Test specimens from finished goods shall be taken
3 Principle
from flat areas or zones having minimum curvature.
For reinforced plastics, test specimens should not be
See IS0 527-l :1993, clause 3.
machined to reduce their thickness unless abs
...