Tunnelling machines - Road headers, continuous miners and impact rippers - Safety requirements

Tunnelbaumaschinen - Teilschnittmaschinen, Continuous miners und Schlagkopfmaschinen - Sicherheitstechnische Anforderungen

Machines pour la construction de tunnels - Machines à attaque ponctuelle, mineurs continus et brise-roches hydrauliques - Règles de sécurité

Stroji za gradnjo predorov - Odkopne naprave - Varnostne zahteve

General Information

Status
Not Published
Current Stage
5060 - Closure of Vote - Formal Approval
Start Date
27-Apr-2009
Completion Date
27-Apr-2009

Relations

Buy Standard

Draft
EN 12111:2003/kprA1:2009
English language
7 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-februar-2009
Stroji za gradnjo predorov - Odkopne naprave - Varnostne zahteve
Tunnelling machines - Road headers, continuous miners and impact rippers - Safety
requirements
Tunnelbaumaschinen - Teilschnittmaschinen, Continuous miners und
Schlagkopfmaschinen - Sicherheitstechnische Anforderungen
Machines pour la construction de tunnels - Machines à attaque ponctuelle, mineurs
continus et brise-roches hydrauliques - Règles de sécurité
Ta slovenski standard je istoveten z: EN 12111:2002/prA1
ICS:
91.220 Gradbena oprema Construction equipment
93.060 Gradnja predorov Tunnel construction
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
FINAL DRAFT
EN 12111:2002
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
November 2008
ICS 91.220; 93.060
English Version
Tunnelling machines - Road headers, continuous miners and
impact rippers - Safety requirements
Machines pour la construction de tunnels - Machines à Tunnelbaumaschinen - Teilschnittmaschinen, Continuous
attaque ponctuelle, mineurs continus et brise-roches miners und Schlagkopfmaschinen - Sicherheitstechnische
hydrauliques - Règles de sécurité Anforderungen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 151.
This draft amendment A1, if approved, will modify the European Standard EN 12111:2002. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12111:2002/prA1:2008: E
worldwide for CEN national Members.

Contents Page
Foreword.3
1 Modification to Clause 2 .4
2 Modification to 5.1.1 .4
3 Modification to 5.6.4.1 .4
4 Addition of 5.6.6.4
5 Modification to 7.1 .4
6 Modification to 7.2.2 .5
7 Modification to 7.3.1 .5
8 Modification to Annex ZA .6
9 Addition of Annex ZB .7

Foreword
This document (EN 12111:2002/prA1:2008) has been prepared by Technical Committee CEN/TC 151
“Construction equipment and building material machines - Safety”, the secretariat of which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EC Directive(s).
For relationship with EC Directive(s), see informative Annex ZA, B, C or D, which is an integral part of this
document.
The main changes compared to the previous version are:
 Addition of Annex ZB;
 Editorial modification of Annex ZA;
 “Minor” changes of sub-clauses 5.6.6, 7.1, 7.2.2 and 7.3.1;
 reference to EN 292-1 be replaced by EN ISO 12100-1:2003 and EN 292-2 be replace by
EN ISO 12100-2: 2003.
1 Modification to Clause 2
Replace "EN 292-1:1991" with "EN ISO 12100-1:2003 Safety of machinery — Basic concepts, general
principles for design — Part 1: Basic termino
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.