EN 13362:2005
(Main)Geosynthetic Barriers - Characteristics required for use in the construction of canals
Geosynthetic Barriers - Characteristics required for use in the construction of canals
This document specifies the relevant characteristics of geosynthetic barriers, including polymeric geosynthetic barriers, clay geosynthetic barriers and bituminous geosynthetic barriers, when used as fluid barriers in the construction of canals, and the appropriate test methods to determine these characteristics.
The intended use of these products is to control the leakage of water through the construction.
This document is not applicable to geotextiles or geotextile-related products.
This document provides for the evaluation of conformity of the product to this document.
This document defines requirements to be met by manufacturers and their authorised representatives with regard to the presentation of product properties.
This document does not cover applications where the geosynthetic barrier is to be in contact with water that has been treated for human consumption.
NOTE Where potable water is or may be in direct contact with the product the designer should also refer to other relevant standards, requirements and/or regulations.
.
Geosynthetische Dichtungsbahnen - Eigenschaften, die für die Anwendung beim Bau von Kanälen erforderlich sind
Dieses Dokument legt die relevanten Eigenschaften von geosynthetischen Dichtungsbahnen, einschließlich
geosynthetischer Kunststoffdichtungsbahnen, geosynthetischer Tondichtungsbahnen und geosynthetischer
Bitumen-dichtungsbahnen, die als Abdichtung beim Bau von Kanälen verwendet werden, und die geeigneten
Prüfverfahren zur Bestimmung dieser Eigenschaften fest.
Die bestimmungsgemäße Anwendung dieser Produkte besteht in dem Abdichten gegen das Durchsickern von
Wasser durch das Bauwerk.
Dieses Dokument ist nicht anwendbar auf Geotextilien oder geotextilverwandte Produkte.
Dieses Dokument ermöglicht die Konformitätsbewertung des Produktes hinsichtlich dieses Dokuments.
Dieses Dokument legt die Anforderungen fest, die von Herstellern und Händlern in Bezug auf die Darstellung der
Produkteigenschaften eingehalten werden müssen.
Dieses Dokument umfasst nicht die Anwendungen, bei denen die geosynthetische Dichtungsbahn in Kontakt mit
Trinkwasser kommt, das für den unmittelbaren menschlichen Gebrauch behandelt wurde.
ANMERKUNG Wo Trinkwasser in direkten Kontakt mit dem Produkt kommt oder kommen kann, muss sich der Planer auf
andere zutreffende Normen, Anforderungen und/oder Bestimmungen beziehen.
Géomembranes, géosynthétiques bentonitiques - Caractéristiques requises pour l'utilisation dans la construction des canaux
Le présent document spécifie les caractéristiques requises pour les géomembranes et géosynthétiques bentonitiques destinés à éviter la pénétration de fluides dans la structure des canaux ; elle décrit par ailleurs les méthodes d'essai permettant de déterminer ces caractéristiques.
L' usage attendu de ces produits est de contrôler les fuites d'eau dans la construction.
Le présent document ne s'applique pas aux géotextiles ou produits apparentés.
Il donne les informations permettant d'évaluer la conformité du produit au présent document.
le présent document définit les exigences auxquelles les fabricants et leurs représentants attitrés doivent satisfaire pour la présentation des propriétés du produit.
Il ne couvre pas les cas où la géomembrane doit se trouver en contact avec une eau traitée en vue d'une consommation domestique.
NOTE Si de l'eau potable doit ou peut se trouver en contact direct avec le produit, il convient que le concepteur se réfère également aux autres normes, exigences et/ou règlements applicables.
Geosintetične ovire - Značilnosti, ki se zahtevajo pri gradnji kanalov
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2005
*HRVLQWHWLþQHRYLUH=QDþLOQRVWLNLVH]DKWHYDMRSULJUDGQMLNDQDORY
Geosynthetic Barriers - Characteristics required for use in the construction of canals
Geosynthetische Dichtungsbahnen - Eigenschaften, die für die Anwendung beim Bau
von Kanälen erforderlich sind
Géomembranes, géosynthétiques bentonitiques - Caractéristiques requises pour
l'utilisation dans la construction des canaux
Ta slovenski standard je istoveten z: EN 13362:2005
ICS:
59.080.70 Geotekstilije Geotextiles
93.140 *UDGQMDYRGQLKSRWLLQ Construction of waterways
SULVWDQLãþ and ports
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 13362
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2005
ICS 59.080.70; 91.100.50
English version
Geosynthetic Barriers - Characteristics required for use in the
construction of canals
Géomembranes - Géosynthétiques bentonitiques - Geosynthetische Dichtungsbahnen - Eigenschaften, die für
Caractéristiques requises pour l'utilisation dans la die Anwendung beim Bau von Kanälen erforderlich sind
construction des canaux
This European Standard was approved by CEN on 15 March 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13362:2005: E
worldwide for CEN national Members.
EN 13363:2005 (E)
Contents
Page
Foreword .3
Introduction.4
1 Scope .5
2 Normative references .6
3 Definitions and abbreviations.8
3.1 Terms and definitions.8
3.2 Abbreviations .8
4 Required characteristics and corresponding methods of test.8
4.1 General .8
4.2 Types of Application.8
4.3 Relevant characteristics.10
4.4 Characteristics relevant to specific conditions of use.14
5 Evaluation of conformity .15
5.1 Presentation of characteristics.15
5.2 Verification of values .15
5.3 Initial type tests.15
5.4 Factory production control .16
5.5 Inspection.16
6 Marking .16
Annex A (normative) Scheme of factory production control.17
Annex B (normative) Durability of geosynthetic barriers .19
Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU
Construction Products Directive. .24
Bibliography.30
EN 13363:2005 (E)
Foreword
This document (EN 13362:2005) has been prepared by Technical Committee CEN/TC 189 “Geosynthetics”, the
secretariat of which is held by IBN.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by October 2005, and conflicting national standards shall be withdrawn at the latest
by January 2007.
This document has been prepared under a mandate given to CEN by the European Commission and the European
Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark,
Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EN 13363:2005 (E)
Introduction
This European Standard allows manufacturers to describe geosynthetic barriers on the basis of declared values for
characteristics relevant to the intended use and if tested to the specified method. It also includes procedures for
evaluation of conformity and factory production control.
This European Standard may also be used by designers, end-users and other interested parties as a tool to define
relevant and appropriate characteristics for specifications and on-site quality control. It should be emphasised
however that not all characteristics and test methods quoted in this document are suitable for the purpose of on-site
quality control.
Tests for several non-mandated characteristics are still under study and will be included when the standard is
revised.
The term “product” used in this document refers to a geosynthetic barrier, including polymeric geosynthetic barriers,
clay geosynthetic barriers and bituminous geosynthetic barriers.
This European Standard is part of a group of standards, addressing the requirements for geosynthetic barriers
when used in a specific application.
Particular application cases may contain requirements about additional properties and - preferably standardised -
test methods, if they are technically relevant and not conflicting with European Standards.
The design life of the product should be determined, since its function may be temporary, as a construction
expediency, or permanent, for the lifetime of the structure.
EN 13363:2005 (E)
1 Scope
This European Standard specifies the relevant characteristics of geosynthetic barriers, including polymeric
geosynthetic barriers, clay geosynthetic barriers and bituminous geosynthetic barriers, when used as fluid barriers
in the construction of canals, and the appropriate test methods to determine these characteristics.
The intended use of these products is to control the leakage of water through the construction.
This European Standard is not applicable to geotextiles or geotextile-related products.
This European Standard provides for the evaluation of conformity of the product to this European Standard.
This European Standard defines requirements to be met by manufacturers and their authorised representatives
with regard to the presentation of product properties.
This European Standard does not cover applications where the geosynthetic barrier is to be in contact with water
that has been treated for human consumption.
NOTE Where potable water is or may be in direct contact with the product the designer should also refer to other relevant
standards, requirements and/or regulations.
EN 13363:2005 (E)
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references,
only the edition cited applies. For undated references, the latest edition of the referenced document (including any
amendments) applies.
EN 495-5 Flexible sheets for waterproofing - Determination of foldability at low
temperature - Part 5: Plastic and rubber sheets for roof waterproofing
EN 1109 Flexible sheets for waterproofing - Bitumen sheets for roof waterproofing
– Determination of flexibility at low temperatures
EN 1849-1 Flexible sheets for waterproofing – Determination of thickness and mass
per unit area – Part 1: Bitumen sheets for roof waterproofing
EN 1849-2 Flexible sheets for waterproofing – Determination of thickness and mass
per unit area – Part 2: Plastic and rubber sheets for roof waterproofing
EN 12224 Geotextiles and geotextile-related products – Determination of the
resistance to weathering
EN 12225 Geotextiles and geotextile-related products – Method for determining the
microbiological resistance by a soil burial test
EN 12310-1 Flexible sheets for waterproofing – Part 1: Bitumen sheets for
waterproofing - Determination of resistance to tearing (nail shank)
EN 12311-1 Flexible sheets for waterproofing – Part 1: Bitumen sheets for roof
waterproofing - Determination of tensile properties
EN 13361 Geosynthetic barriers - Characteristics required for use in the
construction of reservoirs and dams.
EN 13491 Geosynthetic barriers - Characteristics required for use as a fluid barrier
in the construction of tunnels and underground structures.
EN 13492 Geosynthetic barriers - Characteristics required for use in the
construction of liquid waste disposal sites, transfer stations or secondary
containment
EN 13493 Geosynthetic barriers - Characteristics required for use in the
construction of solid waste storage and disposal sites.
prEN 14150 Geosynthetic barriers – Determination of permeability to liquids
prEN 14151 Geosynthetic barriers - Determination of burst strength
EN 14196
Geosynthetics - Test methods for measuring mass per unit area of clay
geosynthetic barriers
EN 14414 Geosynthetics - Screening test method for determining chemical
resistance for landfill applications
EN 14415 Geosynthetic barriers – Test method for determining the of resistance to
leaching
prCEN/TS 14416 Geosynthetic barriers – Test method for determining the resistance to
roots
EN 13363:2005 (E)
prCEN/TS 14417 Geosynthetic barriers – Test method for the determination of the
influence of wetting-drying cycles on the permeability of clay geosynthetic
barriers
prCEN/TS 14418 Geosynthetic barriers – Test method for the determination of the
influence of freezing-thawing cycles on the permeability of clay
geosynthetic barriers
EN 14575 Geosynthetic barriers – Screening test method for determining the
resistance to oxidation
EN ISO 527-1:1996 Plastics - Determination of tensile properties - Part 1: General principles
(ISO 527-1:1993 including Corr 1:1994)
EN ISO 527-3 Plastics -- Determination of tensile properties -- Part 3: Test conditions for
films and sheets (ISO 527-3)
EN ISO 527-4 Plastics - Determination of tensile properties - Part 4: Test conditions for
isotropic and orthotropic fibre-reinforced plastic composites (ISO 527-4)
EN ISO 9862 Geosynthetics - Sampling and preparation of test specimens (ISO
9862:2005)
EN ISO 9863-1 Geosynthetics - Determination of thickness at specified pressures - Part
1: Single layers (ISO 9863-1:2005)
prEN ISO 10318:2003 Geosynthetics - Geotextiles, geotextile-related products, geomembranes
and geosynthetic clay liners - Terms and their definitions (ISO/DIS
10318:2000))
EN ISO 10319 Geotextiles - Wide-width tensile test (ISO 10319:1993)
EN ISO 10320 Geotextiles and geotextile-related products – Identification on site (ISO
10320:1999)
EN ISO 12236 Geotextiles and geotextile-related products – Static puncture test (CBR
test) (ISO 12236:1996)
EN ISO 12957-1 Geosynthetics – Determination of friction characteristics – Part 1: Direct
shear test. (ISO 12957-1:2005)
EN ISO 12957-2 Geosynthetics – Determination of friction characteristics - Part 2: Inclined
plane test. (ISO 12957-2:2005)
EN ISO 13438 Geotextiles and geotextile-related products – Screening test method for
determining the resistance to oxidation (ISO 13438:2004)
ISO 34-1 Rubber, vulcanized or thermop
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.