iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 14196:2016

(Main)

Geosynthetics - Test methods for measuring mass per unit area of clay geosynthetic barriers

Geosynthetics - Test methods for measuring mass per unit area of clay geosynthetic barriers

This European Standard describes a test method for the laboratory determination of the mass per unit area of a sample of clay geosynthetic barrier (GBR-C) in the condition as received.
Since manufacturers quote mass per unit area at a given moisture content, it is necessary to measure the moisture content.

Geokunststoffe - Prüfverfahren zur Bestimmung der flächenbezogenen Masse von geosynthetischen Tondichtungsbahnen

Géosynthétiques - Méthodes d'essai pour la détermination de la masse surfacique des barrières géosynthétiques argileuses bentonitiques

La présente Norme européenne décrit une méthode d’essai pour la détermination en laboratoire de la masse surfacique d’un échantillon de géosynthétique bentonitique tel que réceptionné.
Les fabricants indiquant la masse surfacique correspondant à une teneur en eau donnée ; il est donc nécessaire de mesurer la teneur en eau.

Geosintetika - Preskusne metode za merjenje mase glinenih geosintetičnih zapor

Ta evropski standard opisuje preskusno metodo za laboratorijsko ugotavljanje mase na enoto površine vzorca glinene geosintetične zapore (GBR-C) v prejetem stanju. Ker proizvajalci navedejo vrednost mase na enoto površine pri dani vsebnosti vlage, je treba izmeriti vsebnost vlage.

General Information

Status
Published
Publication Date
16-Feb-2016
Withdrawal Date
30-Aug-2016
ICS
59.080.70 - Geotextiles
91.100.50 - Binders. Sealing materials
Technical Committee
CEN/TC 189 - Geotextiles and geotextile-related products
Drafting Committee
CEN/TC 189/WG 2 - Terminology, identification, sampling and classification
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
27-Jan-2022
Ref Project
SIST EN 14196:2016 - Geosynthetics - Test methods for measuring mass per unit area of clay geosynthetic barriers

Relations

Replaces
EN 14196:2003 - Geosynthetics - Test methods for measuring mass per unit area of clay geosynthetic barriers
Effective Date
24-Feb-2016

Buy Standard

EN 14196:2016EN 14196:2016
PreviousNext
Standard
EN 14196:2016
English language
7 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Geokunststoffe - Prüfverfahren zur Bestimmung der flächenbezogenen Masse von geosynthetischen TondichtungsbahnenGéosynthétiques - Méthodes d'essai pour la détermination de la masse par unité de surface des barrières géosynthétiques bentonitiquesGeosynthetics - Test methods for measuring mass per unit area of clay geosynthetic barriers59.080.70GeotekstilijeGeotextilesICS:Ta slovenski standard je istoveten z:EN 14196:2016SIST EN 14196:2016en,fr,de01-april-2016SIST EN 14196:2016SLOVENSKI
STANDARDSIST EN 14196:20041DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14196
February
t r s x ICS
w {ä r z rä y râ
{ sä s r rä w r Supersedes EN
s v s { xã t r r uEnglish Version
Geosynthetics æ Test methods for measuring mass per unit area of clay geosynthetic barriers Géosynthétiques æ Méthodes d 5essai pour la détermination de la masse surfacique des barrières géosynthétiques argileuses bentonitiques
Geokunststoffe æ Prüfverfahren zur Bestimmung der flächenbezogenen Masse von geosynthetischen Tondichtungsbahnen This European Standard was approved by CEN on
s { December
t r s wä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
t r s x CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s v s { xã t r s x ESIST EN 14196:2016

of the synthetic component . 7 A.1 Apparatus . 7 A.1.1 Oven . 7 A.1.2 Blowing or suction apparatus . 7 A.1.3 Balances . 7 A.2 Procedure. 7 A.3 Calculation . 7
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 13428:2024(Main)
Geosynthetics - Determination of the protection efficiency of a geosynthetic against impact damage (ISO 13428:2024)
SIST EN ISO 13428:2024

This document describes an index test for the determination of the protection efficiency of a geosynthetic on a hard surface, exposed to the impact load of a hemispherical object.
The index test measures the change in thickness of a thin lead plate lying between the geosynthetic and a rigid support.
It is also used as a performance test, by using the real rigid surface to protect and the real sequence of geosynthetics.
The test is applicable to all geosynthetics with apertures smaller than 15 mm (maximum size).

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16416:2023(Main)
Geosynthetic clay barriers - Determination of water flux index - Flexible wall permeameter method at constant head
SIST EN 16416:2023

This document specifies an index test method that covers laboratory measurement of water flux through saturated clay geosynthetic barrier (GBR-C) specimens using a flexible wall permeameter at constant head.
This test method is applicable to GBR-C products with no additional sealing layers attached (e.g. polymeric or bituminous).
This test method specifies a measurement of flux under a prescribed set of conditions that can be used for manufacturing quality control. The test method can also be used to check conformance.
The flux value determined using this test method is not considered to be representative of the in-service flux of a GBR-C.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13493:2018(Main)
Geosynthetic barriers - Characteristics required for use in the construction of solid waste storage and disposal sites
SIST EN 13493:2018

This European Standard specifies the characteristics of geosynthetic barriers, including polymeric geosynthetic barriers, clay geosynthetic barriers and bituminous geosynthetic barriers, when used as fluid barriers and separation layer in the construction of solid waste storage and disposal sites, and the appropriate test methods to determine these characteristics.
The intended use of these products is to control the leakage of fluids through the construction.
This European Standard is not applicable to geotextiles or geotextile-related products as defined in EN ISO 10318-1.
This European Standard provides for the assessment and verification of constancy of performance (AVCP) of the product to this European Standard including factory production control procedures.
This European Standard defines characteristics to be considered with regard to the presentation of performance.
NOTE   Where potable water is or can be in direct contact with the product, other relevant standards, requirements and/or regulations can be considered for the design.

  • Standard
    61 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13492:2018(Main)
Geosynthetic barriers - Characteristics required for use in the construction of liquid waste disposal sites, transfer stations or secondary containment
SIST EN 13492:2018

This European Standard specifies the characteristics of geosynthetic barriers, including polymeric geosynthetic barriers, clay geosynthetic barriers and bituminous geosynthetic barriers, when used as fluid barriers and separation layer in the construction of liquid waste disposal sites, and in the construction of transfer stations or secondary containment for the storage of liquid waste on a waste disposal site only and the appropriate test methods to determine these characteristics.
The intended use of these products is to control the leakage of fluids through the construction.
This European Standard is not applicable to geotextiles or geotextile-related products as defined in EN ISO 10318-1.
This European Standard provides for the assessment and verification of constancy of performance (AVCP) of the product to this European Standard including factory production control procedures.
This European Standard defines characteristics to be considered with regard to the presentation of performance.
NOTE   Where potable water is or can be in direct contact with the product, other relevant standards, requirements and/or regulations can be considered for the design.

  • Standard
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16993:2018(Main)
Geosynthetic barriers - Characteristics required for use in the construction of storage lagoons, secondary containment (above and below ground) and other containment applications for chemicals, polluted water and produced liquids
SIST EN 16993:2018

This European Standard specifies the characteristics of geosynthetic barriers, including polymeric geosynthetic barriers, clay geosynthetic barriers and bituminous geosynthetic barriers used as fluid barriers and separation layer in the construction of hazardous liquid containment and secondary containment around storage facilities for hazardous liquids and the appropriate test methods to determine these characteristics.
NOTE   This document is not applicable to applications where one geosynthetic barrier is manufactured in direct contact with a second geosynthetic barrier in order to reduce the overall permeability of the barrier. Such "multicomponent" products are subject to the required characteristics for the relevant component.
The intended use of these products is to control the leakage of fluids through the construction.
This European Standard is not applicable to geotextiles or geotextile-related products as defined in EN ISO 10318-1.
This European Standard provides for the assessment and verification of constancy of performance (AVCP) of the product to this European Standard including factory production control procedures.
This European Standard defines characteristics to be considered with regard to the presentation of performance.

  • Standard
    63 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13491:2018(Main)
Geosynthetic barriers - Characteristics required for use in the construction of tunnels and associated underground structures
SIST EN 13491:2018

This document specifies the characteristics of geosynthetic barriers, including polymeric geosynthetic barriers, clay geosynthetic barriers and bituminous geosynthetic barriers, when used as fluid barriers and separation layer in the construction of tunnels and associated underground structures, and the appropriate test methods to determine these characteristics.
The intended use of these products is to control the leakage of fluid through the construction.
This document is not applicable to geotextiles or geotextile-related products as defined in EN ISO 10318 1.
This document provides for the assessment and verification of constancy of performance (AVCP) of the product to this European Standard including factory production control procedures.
This document defines characteristics to be considered with regard to the presentation of performance.
This document does not cover applications where the geosynthetic barrier is to be in contact with water that has been treated for human consumption.
NOTE   Where potable water is or can be in direct contact with the product, other relevant standards, requirements and/or regulations can be considered for the design.

  • Standard
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16994:2018(Main)
Clay Geosynthetic Barriers - Characteristics required for use in the construction of underground structures (other than tunnels and associated structures)
SIST EN 16994:2018

This document specifies the characteristics of clay geosynthetic barriers (GBR-C) as well as multicomponent geosynthetic clay barriers (e.g. a GBR-C with a polymeric or bituminous geosynthetic barrier attached to it), when used as fluid barriers and separation layer in the construction of underground structures (other than tunnels and associated structures), and the appropriate test methods to determine these characteristics.
If in a multicomponent GBR-C, the GBR-P or GBR-B is the predominant hydraulic barrier then the appropriate standard should be used.
The intended use of these products is to control the leakage of fluid through the construction wall.
This document is not applicable to geotextiles or geotextile-related products as defined in EN ISO 10318 1.
This document provides for the assessment and verification of constancy of performance (AVCP) of the product to this European Standard including factory production control procedures.
This document defines characteristics to be considered with regard to the presentation of performance.
This document does not cover applications where the geosynthetic barrier is to be in contact with water that has been treated for human consumption.
NOTE   Where potable water is or can be in direct contact with the product, other relevant standards, requirements and/or regulations can be considered for the design.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13362:2018(Main)
Geosynthetic Barriers - Characteristics required for use in the construction of canals
SIST EN 13362:2018

This European Standard specifies the characteristics of geosynthetic barriers, including polymeric geosynthetic barriers, clay geosynthetic barriers and bituminous geosynthetic barriers, when used as fluid barriers and separation layer forwater, in the construction of canals and the appropriate test methods to determine these characteristics.
The intended use of these products is to control the leakage of the fluid through the construction.
This document is not applicable to geotextiles or geotextile-related products, as defined in EN ISO 10318 1.
This document provides for the assessment and verification of constancy of performance (AVCP) of the product to this European Standard including factory production control procedures.
This document defines characteristics to be considered with regard to the presentation of performance.
This document does not cover applications where the geosynthetic barrier is to be in contact with water that has been treated for human consumption.
NOTE   Where potable water is or can be in direct contact with the product, other relevant standards, requirements and/or regulations can be considered for the design.

  • Standard
    58 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13361:2018(Main)
Geosynthetic barriers - Characteristics required for use in the construction of reservoirs and dams
SIST EN 13361:2018

This document specifies the characteristics of geosynthetic barriers, including polymeric geosynthetic barriers, clay geosynthetic barriers and bituminous geosynthetic barriers, when used as fluid barriers and separation layer for water, in the construction of reservoirs and dams, and the appropriate test methods to determine these characteristics.
The intended use of these products is to control the leakage of potable, fresh or saline water through the construction.
This document is not applicable to geotextiles or geotextile-related products, as defined in EN ISO 10318 1.
This document provides for the assessment and verification of constancy of performance (AVCP) of the product to this European Standard including factory production control procedures.
This document defines characteristics to be considered with regard to the presentation of performance.
NOTE   Where potable water is or can be in direct contact with the product, other relevant standards, requirements and/or regulations can be considered for the design.

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13719:2016(Main)
Geosynthetics - Determination of the long term protection efficiency of geosynthetics in contact with geosynthetic barriers
SIST EN 13719:2016

This European Standard is an index test used to determine the efficiency with which a geosynthetic product will protect a geosynthetic barrier or other contact surface against the mechanical long term effects of static point loads.
The test is performed on the geosynthetic product in isolation. It measures the strains experienced by a geosynthetic product in contact with a deformable pad.
NOTE   Other properties relevant to the protection of geosynthetic barriers against differing actions are covered by other standards, e.g. dynamic perforation is covered in EN ISO 13433.
A related performance test simulating specific site conditions is described in Annex B (informative).

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day