CEN ISO/TS 13143-1:2011
(Main)Electronic fee collection - Evaluation of on-board and roadside equipment for conformity to ISO/TS 12813 - Part 1: Test suite structure and test purposes (ISO/TS 13143-1:2011)
Electronic fee collection - Evaluation of on-board and roadside equipment for conformity to ISO/TS 12813 - Part 1: Test suite structure and test purposes (ISO/TS 13143-1:2011)
ISO/TS 13143-1:2011 specifies the test suite structure (TSS) and test purposes (TP) to evaluate the conformity of on board units (OBU) and roadside equipment (RSE) to ISO/TS 12813. It provides a basis for conformance tests for dedicated short range communication (DSRC) equipment (on board units and roadside units) to enable interoperability between different equipment supplied by different manufacturers.
Straßenverkehrstelematik - Elektronische Gebührenerfassung - Konformitätskontrolle für GNSS/CN Systeme über DSRC (ISO/TS 13143-1:2011)
Perception du télépéage - Évaluation des équipements embarqués et en bord de route quant à la conformité avec l'ISO/TS 12813 - Partie 1: Structure de suite d'essais et buts des essais (ISO/TS 13143-1:2011)
Elektronsko pobiranje pristojbin - Ugotavljanje skladnosti opreme v vozilu in obcestni napravi s tehnično specifikacijo ISO/TS 12813 - 1. del: Zgradba preskuševalnega niza in namen preskušanja (ISO/TS 13143-1:2011)
Ta del ISO/TS 13143 določa zgradbo preskuševalnega niza (TSS) in namena preskušanja (TP) za ugotavljanje skladnosti enot v vozilu (OBU) in obcestni napravi (RSE) z ISO/TS 13141:2010. Zagotavlja podlago za preskuse skladnosti za namensko komunikacijsko opremo kratkega dosega (DSRC) (enote na krovih ladij in obcestne enote) za zagotavljanje interoperabilnosti med različno opremo, ki jo dostavljajo različni proizvajalci.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2011
(OHNWURQVNRSRELUDQMHSULVWRMELQ8JRWDYOMDQMHVNODGQRVWLRSUHPHYYR]LOXLQ
REFHVWQLQDSUDYLVWHKQLþQRVSHFLILNDFLMR,6276GHO =JUDGED
SUHVNXãHYDOQHJDQL]DLQQDPHQSUHVNXãDQMD ,6276
Electronic fee collection - Evaluation of on-board and roadside equipment for conformity
to ISO/TS 12813 - Part 1: Test suite structure and test purposes (ISO/TS 13143-1:2011)
Straßenverkehrstelematik - Elektronische Gebührenerfassung - Konformitätskontrolle für
GNSS/CN Systeme über DSRC (ISO/TS 13143-1:2011)
Perception du télépéage - Évaluation des équipements embarqués et en bord de route
quant à la conformité avec l'ISO/TS 12813 - Partie 1: Structure de suite d'essais et buts
des essais (ISO/TS 13143-1:2011)
Ta slovenski standard je istoveten z: CEN ISO/TS 13143-1:2011
ICS:
03.220.20 Cestni transport Road transport
35.240.60 Uporabniške rešitve IT v IT applications in transport
transportu in trgovini and trade
43.040.15 $YWRPRELOVNDLQIRUPDWLND Car informatics. On board
9JUDMHQLUDþXQDOQLãNLVLVWHPL computer systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
TECHNICAL SPECIFICATION
CEN ISO/TS 13143-1
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
April 2011
ICS 35.240.60; 03.220.20
English Version
Electronic fee collection - Evaluation of on-board and roadside
equipment for conformity to ISO/TS 12813 - Part 1: Test suite
structure and test purposes (ISO/TS 13143-1:2011)
Perception du télépéage - Évaluation des équipements Straßenverkehrstelematik - Elektronische
embarqués et en bord de route quant à la conformité avec Gebührenerfassung - Konformitätskontrolle für GNSS/CN
l'ISO/TS 12813 - Partie 1: Structure de suite d'essais et Systeme über DSRC (ISO/TS 13143-1:2011)
buts des essais (ISO/TS 13143-1:2011)
This Technical Specification (CEN/TS) was approved by CEN on 18 October 2010 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN ISO/TS 13143-1:2011: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (CEN ISO/TS 13143-1:2011) has been prepared by Technical Committee CEN/TC 278 “Road
transport and traffic telematics” the secretariat of which is held by NEN, in collaboration with Technical
Committee ISO/TC 204 "Intelligent transport systems".
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Croatia, Cyprus,
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.
TECHNICAL ISO/TS
SPECIFICATION 13140-1
First edition
2011-04-15
Electronic fee collection — Evaluation of
on-board and roadside equipment for
conformity to ISO/TS 13141 —
Part 1:
Test suite structure and test purposes
Perception du télépéage — Évaluation des équipements embarqués et
en bord de route quant à la conformité avec l'ISO/TS 13141 —
Partie 1: Structure de suite d'essai et buts des essais
Reference number
ISO/TS 13140-1:2011(E)
©
ISO 2011
ISO/TS 13140-1:2011(E)
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
ISO/TS 13140-1:2011(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.1
3 Terms and definitions .2
4 Abbreviated terms.4
5 Test suite structure (TSS).5
5.1 Structure.5
5.2 Reference to conformance test specifications .6
5.3 Test Purposes (TP).6
5.3.1 TP Definition conventions .6
5.3.2 TP naming conventions.7
5.4 Conformance test report.7
Annex A (normative) Test purposes for on-board units.8
Annex B (normative) Test purposes for roadside equipment.26
Annex C (normative) PCTR for on-board units.32
Annex D (normative) PCTR for roadside equipment.38
Bibliography.44
ISO/TS 13140-1:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
In other circumstances, particularly when there is an urgent market requirement for such documents, a
technical committee may decide to publish other types of document:
⎯ an ISO Publicly Available Specification (ISO/PAS) represents an agreement between technical experts in
an ISO working group and is accepted for publication if it is approved by more than 50 % of the members
of the parent committee casting a vote;
⎯ an ISO Technical Specification (ISO/TS) represents an agreement between the members of a technical
committee and is accepted for publication if it is approved by 2/3 of the members of the committee casting
a vote.
An ISO/PAS or ISO/TS is reviewed after three years in order to decide whether it will be confirmed for a
further three years, revised to become an International Standard, or withdrawn. If the ISO/PAS or ISO/TS is
confirmed, it is reviewed again after a further three years, at which time it must either be transformed into an
International Standard or be withdrawn.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO/TS 13140-1 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 278, Road transport and traffic telematics, in collaboration with Technical Committee ISO/TC 204,
Intelligent transport systems, in accordance with the Agreement on technical cooperation between ISO and
CEN (Vienna Agreement).
ISO/TS 13140 consists of the following parts, under the general title Electronic fee collection — Evaluation of
on-board and roadside equipment for conformity to ISO/TS 13141:
⎯ Part 1: Test suite structure and test purposes
⎯ Part 2: Abstract test suite
iv © ISO 2011 – All rights reserved
ISO/TS 13140-1:2011(E)
Introduction
ISO/TS 17575 is part of a set of standards that supports interoperability of autonomous EFC-systems. It
defines the EFC context data, their charge reports and their use of communication infrastructure.
The set of standards also supports short range communication links in the context of autonomous electronic
fee collection (EFC) on-board equipment (OBE) to enable spot checks for the enforcement process. The
application interface is defined in ISO/TS 13141:2010.
Within the set of EFC standards this part of ISO/TS 13140 defines the process and tests for conformity
evaluation of OBE and roadside equipment (RSE) that comply with the requirements in ISO/TS 13141:2010.
This part of ISO/TS 13140 is intended to
⎯ assess OBU and RSE capabilities,
⎯ assess OBU and RSE behaviour,
⎯ serve as a guide for OBU and RSE conformance evaluation and type approval,
⎯ achieve comparability between the results of the corresponding tests applied in different places at
different times, and
⎯ facilitate communications between parties.
This part of ISO/TS 13140 is based on
⎯ ISO/TS 13141:2010,
⎯ the set of dedicated short range communication (DSRC) standards defining the communication stack,
and
⎯ ISO 9646.
This part of ISO/TS 13140 is based on using the tree and tabular combined notation (TTCN) that is a
standardized language suitable for specification of test cases and steps for assessment of protocol and
application behaviour. The TTCN language is also supported by modern automated tools that accelerate
software design, implementation and testing.
TECHNICAL SPECIFICATION ISO/TS 13140-1:2011(E)
Electronic fee collection — Evaluation of on-board and roadside
equipment for conformity to ISO/TS 13141 —
Part 1:
Test suite structure and test purposes
1 Scope
This part of ISO/TS 13140 specifies the test suite structure (TSS) and test purposes (TP) to evaluate the
conformity of on-board units (OBU) and roadside equipment (RSE) to ISO/TS 13141:2010.
It provides a basis for conformance tests for dedicated short range communication (DSRC) equipment (on-
board units and roadside units) to enable interoperability between different equipment supplied by different
manufacturers.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the re
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.