EN 13128:2001/prA2

Safety of machine tools - Milling machines (including boring machines)

Sicherheit von Werkzeugmaschinen - Fräs- und Bohr-Fräsmaschinen

Sécurité des machines-outils - Fraiseuses (comprenant les aléseuses)

Varnost obdelovalnih strojev - Frezalni stroji (vključno z vrtalnimi stroji)

General Information

• Status: Not Published
• ICS: 25.080.20 - Boring and milling machines
• Technical Committee: CEN/TC 143 - Machine tools - Safety
• Drafting Committee: CEN/TC 143/WG 4 - Machining centres, etc. - Safety
• Current Stage: 5060 - Closure of Vote - Formal Approval
• Start Date: 23-Jan-2009
• Completion Date: 23-Jan-2009
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Directive: 98/37/EC - Machinery
• Mandate: M/079 - Mandate to CEN and CENELEC for standardization in the field of machines
• Mandate: M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
• Ref Project: SIST EN 13128:2002/kprA2:2008 - Safety of machine tools - Milling machines (including boring machines)

Relations

• Merged Into: EN 13128:2001+A2:2009 - Safety of machine tools - Milling machines (including boring machines)
• Effective Date: 18-Jan-2023
• Amends: EN 13128:2001 - Safety of machine tools - Milling machines (including boring machines)
• Effective Date: 22-Dec-2008

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 13128:2002/kprA2:2008
01-december-2008
9DUQRVWREGHORYDOQLKVWURMHY)UH]DOQLVWURMLYNOMXþQR]YUWDOQLPLVWURML
Safety of machine tools - Milling machines (including boring machines)
Sicherheit von Werkzeugmaschinen - Fräs- und Bohr-Fräsmaschinen
Sécurité des machines-outils - Fraiseuses (comprenent les aléseuses)
Ta slovenski standard je istoveten z: EN 13128:2001/prA2
ICS:
25.080.20 Frezalniki Boring and milling machines
SIST EN 13128:2002/kprA2:2008 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 13128:2002/kprA2:2008

---------------------- Page: 2 ----------------------

SIST EN 13128:2002/kprA2:2008
EUROPEAN STANDARD
FINAL DRAFT
EN 13128:2001
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA2
October 2008
ICS 25.080.20

English Version
Safety of machine tools - Milling machines (including boring
machines)
Sécurité des machines-outils - Fraiseuses (comprenent les Sicherheit von Werkzeugmaschinen - Fräs- und Bohr-
aléseuses) Fräsmaschinen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 143.
This draft amendment A2, if approved, will modify the European Standard EN 13128:2001. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13128:2001/prA2:2008: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 13128:2002/kprA2:2008
EN 13128:2001/prA2:2008 (E)
Contents Page
Foreword.3
1 Modification to 7.2 Instruction handbook .4
2 Modification to 7.3 Noise declaration .4
3 Modifications to 7.4 Marking .4
4 Modification to Annex ZA .5
5 Addition of Annex ZB .6

2

---------------------- Page: 4 ----------------------

SIST EN 13128:2002/kprA2:2008
EN 13128:2001/prA2:2008 (E)
Foreword
This document (EN 13128:2001/prA2:2008) has been prepared by Technical Committee CEN/TC 143
“Machine tools - Safety”, the secretariat of which is held by SNV.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EC Directive(s).
For relationship with EC Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.


3

---------------------- Page: 5 ----------------------

SIST EN 13128:2002/kprA2:2008
EN 13128:2001/prA2:2008 (E)
1 Modification to 7.2 Instruction handbook
Replace the text of item n) with the following:
"information describing residual risks (e.g. conditions where noise levels are likely to exceed 80 dB (A),
hazards arising from sharp or hot tools/components);"

2 Modification to 7.3 Noise declaration
Add the following note at the end of 7.3:
"NOTE Information on noise emission should also be provided in the sales literature."

3 Modifications to 7.4 Marking
...