EN 10120:2008

Steel sheet and strip for welded gas cylinders

This European Standard specifies requirements for hot-rolled sheet and strip up to 5 mm thickness of steels listed in Table 1 and intended for manufacturing welded gas cylinders.
The general technical delivery conditions in EN 10021 also apply to products supplied in accordance with this European Standard.
NOTE   Sheet and strip made of:
- general structural steels (see EN 10025 series);
- non-alloy and alloy steels for pressure equipment (see EN 10028-1 to EN 10028-6);
- low carbon non-alloy steels for cold forming (see EN 10111 and EN 10130);
- steels with high yield strength for cold forming (see EN 10149);
- cold rolled strip up to 600 mm wide of low carbon non-alloy steels (see EN 10139);
- steels for simple pressure vessels (see EN 10207)
are not covered by this European Standard.

Stahlblech und -band für geschweißte Gasflaschen

Diese Europäische Norm legt die Anforderungen an warmgewalztes Blech und Band bis 5 mm Dicke aus
Stählen nach Tabelle 1 fest, das für die Herstellung geschweißter Gasflaschen bestimmt ist.
Für nach dieser Europäischen Norm gelieferte Erzeugnisse gelten zusätzlich die allgemeinen technischen
Lieferbedingungen nach EN 10021.

Tôles et bandes pour bouteilles à gaz soudées en acier

La présente Norme européenne définit les exigences relatives aux tôles et bandes laminées à chaud
d'épaisseur inférieure ou égale à 5 mm en aciers mentionnés au Tableau 1 et destinés à la fabrication de
bouteilles à gaz soudées.
Les conditions techniques de livraison de l'EN 10021 s'appliquent également aux produits fournis en
conformité avec la présente Norme européenne.

Jeklene pločevine in trakovi za plinske jeklenke

General Information

• Status: Withdrawn
• Publication Date: 02-Sep-2008
• Withdrawal Date: 25-Jul-2017
• ICS: 77.140.50 - Flat steel products and semi-products
• Technical Committee: ECISS/TC 107 - Steels for pressure purposes
• Drafting Committee: ECISS/TC 107 - Steels for pressure purposes
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 26-Jul-2017
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Ref Project: SIST EN 10120:2008 - Steel sheet and strip for welded gas cylinders

Relations

• Replaces: EN 10120:1996 - Steel sheet and strip for welded gas cylinders
• Effective Date: 22-Dec-2008
• Replaced By: EN 10120:2017 - Steel sheet and strip for welded gas cylinders
• Effective Date: 02-Aug-2017

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Stahlblech und -band für geschweißte GasflaschenTôles et bandes pour bouteilles à gaz soudées en acierSteel sheet and strip for welded gas cylinders77.140.50SROL]GHONLFlat steel products and semi-productsICS:Ta slovenski standard je istoveten z:EN 10120:2008SIST EN 10120:2008en,fr,de01-november-2008SIST EN 10120:2008SLOVENSKI
STANDARDSIST EN 10120:19971DGRPHãþD



SIST EN 10120:2008



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10120September 2008ICS 77.140.50Supersedes EN 10120:1996
English VersionSteel sheet and strip for welded gas cylindersTôles et bandes pour bouteilles à gaz soudées en acierStahlblech und -band für geschweißte GasflaschenThis European Standard was approved by CEN on 1 August 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10120:2008: ESIST EN 10120:2008



EN 10120:2008 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Terms and definitions.4 4 Classification and designation.5 5 Information to be supplied by the purchaser.5 5.1 Mandatory information.5 5.2 Options.5 5.3 Example of ordering.6 6 Manufacturing process.6 6.1 Steelmaking process.6 6.2 Delivery condition.6 7 Requirements.6 7.1 Chemical composition.6 7.2 Mechanical properties.7 7.3 Weldability.8 7.4 Tolerances.8 7.5 Surface condition.8 8 Inspection.
...