EN 13617-3:2021
(Main)Petrol filling stations - Part 3: Safety requirements for construction and performance of shear valves
Petrol filling stations - Part 3: Safety requirements for construction and performance of shear valves
This document specifies safety and environmental requirements for the construction and performance of shear valves to be fitted to metering pumps, dispensers, and/or satellite delivery systems installed at petrol filling stations and used to dispense liquid fuels and aqueous urea solution into the tanks of motor vehicles, boats and light aircraft and into portable containers at flow rates up to 200 l · min−1.
This document applies to fuels and their vapours of subdivision Group IIA according to EN ISO/IEC 80079-20-1 and also aqueous urea solution according to ISO 22241-1.
The requirements apply to shear valves at ambient temperatures from −20 °C to +40 °C with the possibility for an extended temperature range.
This document pays particular attention to mechanical and hydraulic characteristics.
This document does not apply to equipment dispensing compressed or liquefied gases.
Tankstellen - Teil 3: Sicherheitstechnische Anforderungen an Bau- und Arbeitsweise von Abscherventilen
Dieses Dokument legt die sicherheitstechnischen und Umweltanforderungen an den Bau und die Arbeitsweise von Abscherventilen an Zapfsäulen, druckversorgten Zapfsäulen und/oder Nebenzapfstellen fest, die an Tankstellen installiert werden für die Abgabe von flüssigen Kraftstoffen und wässriger Harnstofflösung in Tanks von Kraftfahrzeugen, Booten und Leichtflugzeugen sowie in tragbare Behälter bei Durchflussraten von bis zu 200 l · min−1.
Dieses Dokument gilt für Kraftstoffe der Unterbereichsgruppe IIA und deren Dämpfe nach EN ISO/IEC 80079-20-1 und auch für wässrige Harnstofflösung nach ISO 22241-1.
Die Anforderungen gelten für Abscherventile bei Umgebungstemperaturen zwischen −20 °C und +40 °C, wobei ein erweiterter Temperaturbereich möglich ist.
In diesem Dokument werden besonders die mechanischen und hydraulischen Eigenschaften berücksichtigt.
Dieses Dokument gilt nicht für Ausrüstung, die für die Abgabe von verflüssigten oder verdichteten Gasen vorgesehen ist.
Stations-service - Partie 3 : Exigences de sécurité relatives à la construction et aux performances des raccords de sécurité
Le présent document spécifie les exigences relatives à la construction et aux performances en matière de sécurité et de protection de l’environnement des vannes de sécurité à monter sur des distributeurs avec/sans pompe immergée et/ou systèmes de livraison satellites installés sur stations-service et utilisés pour distribuer des carburants liquides et une solution aqueuse d'urée dans les réservoirs de véhicules à moteur, de bateaux, d’avions légers et dans des réservoirs portables, à des débits pouvant atteindre 200 l · min-1.
Le présent document s’applique aux carburants et leurs vapeurs du Groupe de subdivision IIA conformément à l’EN ISO/IEC 80079-20-1, mais également à la solution aqueuse d'urée conformément à l’ISO 22241-1.
Les exigences s’appliquent aux raccords cassants à des températures de –20 °C à +40 °C avec la possibilité d’étendre la plage de température.
Le présent document accorde une importance particulière aux caractéristiques mécaniques et hydrauliques.
Le présent document ne s’applique pas à l’équipement distribuant des gaz comprimés ou liquéfiés.
Bencinski servisi - 3. del: Varnostne zahteve za izdelavo in lastnosti varovalnih ventilov
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2021
Nadomešča:
SIST EN 13617-3:2012
Bencinski servisi - 3. del: Varnostne zahteve za izdelavo in lastnosti varovalnih
ventilov
Petrol filling stations - Part 3: Safety requirements for construction and performance of
shear valves
Tankstellen - Teil 3: Sicherheitstechnische Anforderungen an Bau- und Arbeitsweise von
Abscherventilen
Stations-service - Partie 3 : Exigences de sécurité relatives à la construction et aux
performances des raccords de sécurité
Ta slovenski standard je istoveten z: EN 13617-3:2021
ICS:
75.200 Oprema za skladiščenje Petroleum products and
nafte, naftnih proizvodov in natural gas handling
zemeljskega plina equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 13617-3
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2021
EUROPÄISCHE NORM
ICS 75.200 Supersedes EN 13617-3:2012
English Version
Petrol filling stations - Part 3: Safety requirements for
construction and performance of shear valves
Stations-service - Partie 3 : Exigences de sécurité Tankstellen - Teil 3: Sicherheitstechnische
relatives à la construction et aux performances des Anforderungen an Bau- und Arbeitsweise von
raccords de sécurité Abscherventilen
This European Standard was approved by CEN on 14 June 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13617-3:2021 E
worldwide for CEN national Members.
Contents Page
European foreword . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Explosion protection measures . 7
5 Construction . 7
5.1 General requirements . 7
5.2 Specific requirements . 7
5.3 Classes of construction . 8
5.4 Threads . 8
6 Physical properties . 8
7 Operational requirements . 8
8 Tests . 10
8.1 General . 10
8.2 Type tests . 10
8.3 Production acceptance tests . 10
8.4 Routine tests . 10
9 Information for use . 11
9.1 General . 11
9.2 Marking and instruction . 11
10 Environmental aspects . 11
Annex A (normative) Instructions — Guide for items to be included in manufacturers’
installation and user manual . 12
Annex B (normative) Test methods . 13
B.1 General requirements . 13
B.2 Pressure test of liquid shear valves (routine test) . 13
B.3 Main valve test of liquid shear valve (routine test) . 13
B.4 Pressure relief valve test (routine test) . 14
B.5 Liquid compatibility preconditioning (type test) . 14
B.6 Pressure test (type test) . 14
B.7 Main valve test (type test) . 14
B.8 Check valve test (class I only) (type test) . 15
B.9 Pressure relief valve test (class I only) (type test). 15
B.10 Thermal link test 1 (class I and class II only) (type test and production acceptance
test) . 15
B.11 Thermal link test 2 (class I and class II only) (type test and production acceptance
test) . 15
B.12 Main valve closure test of liquid shear valves (type test and production acceptance
test) . 16
B.13 Main valve closure test of vapour shear valves (type test and production acceptance
test) . 16
B.14 Fire resistance test 1 (type test) . 16
B.15 Fire resistance test 2 (type test) . 17
B.16 Pressure test of vapour shear valves (routine test) . 17
B.17 Main valve test of vapour shear valve (routine test) . 17
Annex C (informative) Environmental aspects . 18
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2014/34/EU aimed to be covered . 20
Bibliography . 22
European foreword
This document (EN 13617-3:2021) has been prepared by Technical Committee CEN/TC 393 “Equipment
for storage tanks and for filling stations”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2022, and conflicting national standards shall be
withdrawn at the latest by March 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13617-3:2012.
In comparison with the 2012 edition, the following significant changes were made:
— shear valves for aqueous urea solution added;
— testing for vapour shear valves further differentiated from testing for fuel shear valves. Tests B.16,
and B.17 are introduced;
— fire resistance test B.14 and B15 introduced and pass/fail criteria defined in Table 3;
— the liquid compatibility preconditioning fluid for shear valves is defined in EN 13617-1.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive 2014/34/EU.
For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document.
EN 13617 consists of four parts:
— Part 1: Safety requirements for construction and performance of metering pumps, dispensers and
remote pumping units;
— Part 2: Safety requirements for construction and performance of safe breaks for use on metering pumps
and dispensers;
— Part 3: Safety requirements for construction and performance of shear valves;
— Part 4: Safety requirements for construction and performance of swivels for use on metering pumps and
dispensers.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
1 Scope
This document specifies safety and environmental requirements for the construction and performance
of shear valves to be fitted to metering pumps, dispensers, and/or satellite delivery systems installed at
petrol filling stations and used to dispense liquid fuels and aqueous urea solution into the tanks of motor
−1
.
vehicles, boats and light aircraft and into portable containers at flow rates up to 200 l · min
This document applies to fuels and their vapours of subdivision Group IIA according to
EN ISO/IEC 80079-20-1 and also aqueous urea solution according to ISO 22241-1.
The requirements apply to shear valves at ambient temperatures from −20 °C to +40 °C with the
possibility for an extended temperature range.
This document pays particular attention to mechanical and hydraulic characteristics.
This document does not apply to equipment dispensing compressed or liquefied gases.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 1127-1:2019, Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and
methodology
EN 13617-1:2021, Petrol filling stations - Part 1: Safety requirements for construction and performance of
metering pumps, dispensers and remote pumping units
EN IEC 60079-0:2018, Explosive atmospheres - Part 0: Equipment - General requirements
(IEC 60079-0:2017)
EN ISO 80079-36:2016, Explosive atmospheres - Part 3
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.