EN 13012:2021
(Main)Petrol filling stations - Construction and performance of automatic nozzles for use on fuel dispensers
Petrol filling stations - Construction and performance of automatic nozzles for use on fuel dispensers
This document specifies safety and environmental requirements for the construction and performance of nozzles to be fitted to metering pumps and dispensers installed at filling stations and which are used to dispense liquid fuels and aqueous urea solution into the tanks of motor vehicles, boats and light aircraft and into portable containers, at flow rates up to 200 l · min−1.
This document applies to fuels of subdivision Group IIA according to EN ISO/IEC 80079-20-1 and also aqueous urea solution according to ISO 22241-1. The requirements apply to automatic nozzles dispensing liquid at ambient temperatures from −20 °C to +40 °C with the possibility for an extended temperature range.
This document does not apply to equipment dispensing compressed or liquefied gases.
This document does not include any requirements for metering performance. Vapour recovery efficiency rates are not covered in this document.
Tankstellen - Anforderungen an Bau und Arbeitsweise von automatischen Zapfventilen für die Benutzung an Zapfsäulen
Dieses Dokument legt die sicherheitstechnischen Anforderungen und Umweltanforderungen an den Bau und die Arbeitsweise von Zapfventilen fest, die an Zapfsäulen und druckversorgten Zapfsäulen an Tankstellen installiert werden für die Abgabe von flüssigen Kraftstoffen und wässriger Harnstofflösung in Tanks von Kraftfahrzeugen, Booten und Leichtflugzeugen sowie in tragbare Behälter bei Durchflussraten von bis zu 200 l · min−1.
Dieses Dokument gilt für Kraftstoffe der Unterbereichsgruppe IIA nach EN ISO/IEC 80079-20-1 und auch für wässrige Harnstofflösung nach ISO 22241-1. Die Anforderungen gelten für automatische Zapfventile für die Abgabe von Flüssigkeiten bei Umgebungstemperaturen von −20 °C bis +40 °C, wobei ein erweiterter Temperaturbereich möglich ist.
Dieses Dokument gilt nicht für Ausrüstung, die für die Abgabe von verflüssigten oder verdichteten Gasen vorgesehen ist.
Dieses Dokument enthält keine Anforderungen für Messausführungen. Effizienzraten für Gasrückführung werden in diesem Dokument nicht behandelt.
Stations-service - Construction et performances des pistolets automatiques de remplissage utilisés sur les distributeurs de carburant
Le présent document spécifie les exigences relatives à la sécurité et à la protection de l'environnement pour la construction et les performances des pistolets de remplissage montés sur des ensembles de mesurage et de distribution installés dans des stations-service et utilisés pour distribuer des carburants liquides et de solution aqueuse d’urée dans des réservoirs de véhicules à moteur, de bateaux, d'avions légers et dans des réservoirs portables, à des débits pouvant atteindre 200 l . min-1.
Le présent document s'applique aux carburants du Groupe de subdvision IIA conformément à l’ISO/IEC 80079-20-1 et aussi aux solutions aqueuses d'urée conformément à l'ISO 22241-1. Les exigences concernent les pistolets automatiques de remplissage distribuant des liquides, à des températures de -20 °C à +40 °C avec la possibilité d’une gamme de température étendue.
Le présent document ne s’applique pas aux équipements mettant en œuvre du gaz de pétrole liquéfié ou compressé.
Le présent document ne comprend aucune exigence concernant les performances métrologiques. Les taux d'efficacité de la récupération de vapeur ne sont pas abordés dans le présent document.
Bencinski servisi - Izdelava in lastnosti avtomatskih točilnih ventilov, vgrajenih v napravah za točenje goriva
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2021
Nadomešča:
SIST EN 13012:2012
Bencinski servisi - Izdelava in lastnosti avtomatskih točilnih ventilov, vgrajenih v
napravah za točenje goriva
Petrol filling stations - Construction and performance of automatic nozzles for use on fuel
dispensers
Tankstellen - Anforderungen an Bau und Arbeitsweise von automatischen Zapfventilen
für die Benutzung an Zapfsäulen
Stations-service - Construction et performances des pistolets automatiques de
remplissage utilisés sur les distributeurs de carburant
Ta slovenski standard je istoveten z: EN 13012:2021
ICS:
75.200 Oprema za skladiščenje Petroleum products and
nafte, naftnih proizvodov in natural gas handling
zemeljskega plina equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 13012
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2021
EUROPÄISCHE NORM
ICS 75.200 Supersedes EN 13012:2012
English Version
Petrol filling stations - Construction and performance of
automatic nozzles for use on fuel dispensers
Stations-service - Construction et performances des Tankstellen - Anforderungen an Bau und Arbeitsweise
pistolets automatiques de remplissage utilisés sur les von automatischen Zapfventilen für die Benutzung an
distributeurs de carburant Zapfsäulen
This European Standard was approved by CEN on 14 June 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13012:2021 E
worldwide for CEN national Members.
Contents Page
European foreword . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Construction . 7
4.1 General . 7
4.2 Guard . 8
4.3 Inlet threads . 8
4.4 Safe break. 10
4.5 Latch . 10
4.6 Automatic de-activating mechanism . 10
5 Physical properties . 10
6 Functional requirements. 10
7 Frequency of testing . 11
8 Marking and instruction . 12
9 Environmental aspects . 13
Annex A (normative) Test preconditioning . 14
A.1 General . 14
A.2 Bending moment preconditioning . 14
A.3 Liquid compatibility pre-conditioning . 14
Annex B (normative) Test methods . 15
B.1 Electrical resistance test . 15
B.2 Pressure test . 15
B.3 Drop test . 15
B.4 Tightness test 1 . 16
B.5 Automatic shut-off device test 1 . 16
B.6 Drain test . 18
B.7 Attitude device test 1 . 18
B.8 Attitude device test 2 . 19
B.9 Automatic de-activating mechanism test . 19
B.10 Line shock generated test . 20
B.11 Tightness test 2 . 20
B.12 Automatic shut-off device test 2 . 20
B.13 Attitude device test 3 . 20
Annex C (informative) Environmental aspects . 21
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2014/34/EU aimed to be covered . 24
Bibliography . 26
European foreword
This document (EN 13012:2021) has been prepared by Technical Committee CEN/TC 393 “Equipment
for storage tanks and for filling stations”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2022, and conflicting national standards shall be
withdrawn at the latest by March 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13012:2012.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
In comparison with the 2012 edition, the following significant changes were made:
— nozzles for aqueous urea solution added;
— Table 2 corrected to ensure compatibility between components according to EN 13012:2021,
EN 13617-2:2021, EN 13617-4:2021 and EN 1360:2013.
— the liquid compatibility preconditioning fluid for fuel nozzles is defined in EN 13617-1:2021.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
1 Scope
This document specifies safety and environmental requirements for the construction and performance
of nozzles to be fitted to metering pumps and dispensers installed at filling stations and which are used
to dispense liquid fuels and aqueous urea solution into the tanks of motor vehicles, boats and light aircraft
−1
.
and into portable containers, at flow rates up to 200 l · min
This document applies to fuels of subdivision Group IIA according to EN ISO/IEC 80079-20-1 and also
aqueous urea solution according to ISO 22241-1. The requirements apply to automatic nozzles
dispensing liquid at ambient temperatures from −20 °C to +40 °C with the possibility for an extended
temperature range.
This document does not apply to equipment dispensing compressed or liquefied gases.
This document does not include any requirements for metering performance. Vapour recovery efficiency
rates are not covered in this document.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 1360:2013, Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems -
Specification
EN 13617-1:2021, Petrol filling stations - Part 1: Safety requirements for construction and performance of
metering pumps, dispensers and remote pumping units
EN 13617-2:2021, Petrol filling stations - Part 2: Safety requirements for construction and performance of
safe breaks for use on metering pumps and dispensers
EN 60204-1:2018, Safety of machinery - Electrical equipment of machines - Part 1: General requirements
(IEC 60204-1:2016, modified)
EN IEC 60079-0:2018, Explosive atmospheres - Part 0: Equipment - General requirements
(IEC 60079-0:2017)
EN ISO 228-1:2003, Pipe threads where pressure-tight joints are not made on the threads - Part 1:
Dimensions, tolerances and designation (ISO 228-1:2000)
EN ISO 80079-36:2016, Explosive atmospheres - Part 36: Non-electrical equipment for explosive
atmospheres - Basic method and requirements (ISO 80079-36:2016)
ISO 261:1998, ISO general purpose metric screw threads — General plan
ISO 965-2:1998, ISO general purpose metric screw threads — Tolerances — Part 2: Limits of sizes for
general purpose external and internal screw threads — Medium quality
ISO 9158:1988, Road vehicles — Nozzle spouts for unleaded gasoline
ISO 9159:1988, Road vehicles — Nozzle spouts for leaded gasoline and diesel fuel
ISO 11925-3:1997, Reaction to fire tests — Ignitability of building products subjected to direct impingement
of flame — Part 3: Multi-source test
ISO 22241-1:2019, Diesel engines — NOx reduction agent AUS 32 — Part 1: Quality requirements
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at https://www.electropedia.org/
3.1
nozzle
manually operated device that controls the flow of liquid medium during a dispensing operation and
includes a spout and an automatic shut-off mechanism
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.