EN ISO 22167:2021
(Main)Solid recovered fuels - Determination of content of volatile matter (ISO 22167:2021)
Solid recovered fuels - Determination of content of volatile matter (ISO 22167:2021)
This document specifies the requirements and a method for the determination of volatile matter of solid recovered fuels.
Feste Sekundärbrennstoffe - Bestimmung des Gehaltes an flüchtigen Substanzen (ISO 22167:2021)
Dieses Dokument legt die Anforderungen und ein Verfahren zur Bestimmung der flüchtigen Bestandteile von festen Sekundärbrennstoffen fest.
Combustibles solides de récupération - Détermination de la teneur en composés volatils (ISO 22167:2021)
Le présent document spécifie les exigences et une méthode pour déterminer la matière volatile des combustibles solides de récupération.
Trdna alternativna goriva - Določevanje hlapnih snovi (ISO 22167:2021)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-junij-2021
Nadomešča:
SIST EN 15402:2011
Trdna alternativna goriva - Določevanje hlapnih snovi (ISO 22167:2021)
Solid recovered fuels - Determination of content of volatile matter (ISO 22167:2021)
Feste Sekundärbrennstoffe - Bestimmung des Gehaltes an flüchtigen Substanzen (ISO
22167:2021)
Combustibles solides de récupération - Détermination de la teneur en composés volatils
(ISO 22167:2021)
Ta slovenski standard je istoveten z: EN ISO 22167:2021
ICS:
75.160.10 Trda goriva Solid fuels
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 22167
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2021
EUROPÄISCHE NORM
ICS 75.160.10 Supersedes EN 15402:2011
English Version
Solid recovered fuels - Determination of content of volatile
matter (ISO 22167:2021)
Combustibles solides de récupération - Détermination Feste Sekundärbrennstoffe - Bestimmung des Gehaltes
de la teneur en composés volatils (ISO 22167:2021) an flüchtigen Substanzen (ISO 22167:2021)
This European Standard was approved by CEN on 9 March 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 22167:2021 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 22167:2021) has been prepared by Technical Committee ISO/TC 300 "Solid
recovered materials, including solid recovered fuels" in collaboration with Technical Committee
CEN/TC 343 “Solid Recovered Fuels” the secretariat of which is held by SFS.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2021, and conflicting national standards
shall be withdrawn at the latest by September 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 15402:2011.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 22167:2021 has been approved by CEN as EN ISO 22167:2021 without any modification.
INTERNATIONAL ISO
STANDARD 22167
First edition
2021-03
Solid recovered fuels — Determination
of content of volatile matter
Combustibles solides de récupération — Détermination de la teneur
en composés volatils
Reference number
ISO 22167:2021(E)
©
ISO 2021
ISO 22167:2021(E)
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved
ISO 22167:2021(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus . 2
5.1 Furnace . 2
5.2 Thermocouple . 3
5.3 Crucible. 4
5.4 Crucible stand . 4
5.5 Balance . 5
6 Sampling and sample preparation . 6
7 Procedure. 6
7.1 Use of automatic equipment . 6
7.2 Number of determinations . 6
7.3 Furnace temperature checking . 6
7.4 Volatile matter determination . 6
8 Calculation . 7
8.1 Case A – without removed ash contributors . 7
8.2 Case B – with removed ash contributors . 7
9 Precision . 9
9.1 Repeatability limit . 9
9.2 Reproducibility limit . 9
10 Test report . 9
Annex A (informative) Interlaboratory test results .10
Annex B (informative) Environmental aspects .13
Bibliography .15
ISO 22167:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 300, Solid recovered fuels, in collaboration
with the European Committee for Standardization (CEN) Technical Committee CEN/TC 343, Solid
recovered fuels, in accordance with the Agreement on technical cooperation between ISO and CEN
(Vienna Agreement).
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2021 – All rights reserved
ISO 22167:2021(E)
Introduction
The volatile matter is determined as the loss in mass of the analysed sample, after moisture removal,
when material is heated up under specific conditions of temperature, time and in a reduced atmosphere
(anoxic conditions). The test is empirical and, in order to ensure reproducible results, it is essential that
the rate of heating, the final temperature and the overall duration of the test are carefully controlled. It
is also essential to exclude air from the solid recovered fuel during heating to prevent oxidation.
The moisture content of the sample is determined at the same time as the vola
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.