EN ISO 8028:2000
(Main)Rubber and/or plastics hoses and hose assemblies for airless paint spraying - Specification (ISO 8028:1999)
Rubber and/or plastics hoses and hose assemblies for airless paint spraying - Specification (ISO 8028:1999)
Gummi- und/oder Kunststoffschläuche und -schlauchleitungen für das luftfreie Farbspritzen - Spezifikation (ISO 8028:1999)
Diese Internationale Norm legt die Anforderungen fest für vier Typen von Schläuchen und Schlauchleitungen für die Verwendung beim luftfreien Farbspritzen. Die Schläuche sind unterschieden nach dem Berstdruck und der Gebrauchstemperatur.
Tuyaux et flexibles en caoutchouc et/ou en plastique pour pulvérisation ¿AIRLESS¿ des peintures - Spécifications (ISO 8028:1999)
La présente Norme internationale spécifie les exigences relatives à quatre types de tuyaux et flexibles en caoutchouc pour utilisation dans la pulvérisation «AIRLESS» des peintures, et différenciés par la pression d'éclatement et la température d'utilisation.
Gumene in/ali polimerne cevi ter cevni priključki za brezzračno brizganje barve - Specifikacija (ISO 8028:1999)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-junij-2001
*XPHQHLQDOLSROLPHUQHFHYLWHUFHYQLSULNOMXþNL]DEUH]]UDþQREUL]JDQMHEDUYH
6SHFLILNDFLMD ,62
Rubber and/or plastics hoses and hose assemblies for airless paint spraying -
Specification (ISO 8028:1999)
Gummi- und/oder Kunststoffschläuche und -schlauchleitungen für das luftfreie
Farbspritzen - Spezifikation (ISO 8028:1999)
Tuyaux et flexibles en caoutchouc et/ou en plastique pour pulvérisation ?AIRLESS? des
peintures - Spécifications (ISO 8028:1999)
Ta slovenski standard je istoveten z: EN ISO 8028:2000
ICS:
83.140.40 Gumene cevi Hoses
87.100 Oprema za nanašanje Paint coating equipment
premazov
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
INTERNATIONAL ISO
STANDARD 8028
Second edition
1999-07-15
Rubber and/or plastics hoses and hose
assemblies for airless paint spraying —
Specification
Tuyaux et flexibles en caoutchouc et/ou en plastique pour pulvérisation
«AIRLESS» des peintures — Spécifications
A
Reference number
ISO 8028:1999(E)
ISO 8028:1999(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 8028 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products,
Subcommittee SC 1, Hoses (rubber and plastics).
This second edition cancels and replaces the first edition (ISO 8028:1987) which has been technically revised.
© ISO 1999
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet iso@iso.ch
Printed in Switzerland
ii
INTERNATIONAL STANDARD © ISO ISO 8028:1999(E)
Rubber and/or plastics hoses and hose assemblies for airless
paint spraying — Specification
WARNING — Persons using this International Standard should be familiar with normal laboratory practice.
This standard does not purport to address all of the safety problems, if any, associated with its use. It is
the responsibility of the user to establish appropriate safety and health practices and to ensure compliance
with any national regulatory conditions.
1 Scope
This International Standard specifies the requirements for four types, differentiated by burst pressure and
temperature of use, of elastomeric hose and hose assembly for use in airless paint spraying.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent editions of the normative documents indicated below. For
undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC
maintain registers of currently valid International Standards.
ISO 471:1995, Rubber — Temperatures, humidities and times for conditioning and testing.
ISO 1402:1994, Rubber and plastics hoses and hose assemblies — Hydrostatic testing.
ISO 1817:1999, Rubber, vulcanized — Determination of the effect of liquids.
ISO 6803:1994, Rubber or plastics hoses and hose assemblies — Hydraulic-pressure impulse test without flexing.
ISO 7326:1991, Rubber and plastics hoses — Assessment of ozone resistance under static conditions.
ISO 7751:1991, Rubber and plastics hoses and hose assemblies — Ratios of proof and burst pressure to design
working pressure.
ISO 8031:1993, Rubber and plas
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.