EN ISO 5459:2011/prA1
(Amendment)Geometrical product specifications (GPS) - Geometrical tolerancing - Datums and datum systems - Amendment 1 (ISO 5459:2011/DAM 1:2022)
Geometrical product specifications (GPS) - Geometrical tolerancing - Datums and datum systems - Amendment 1 (ISO 5459:2011/DAM 1:2022)
Geometrische Produktspezifikation (GPS) - Geometrische Tolerierung - Bezüge und Bezugssysteme - Änderung 1 (ISO 5459:2011/DAM 1:2022)
Spécification géométrique des produits (GPS) - Tolérancement géométrique - Références spécifiées et systèmes de références spécifiées - Amendement 1 (ISO 5459:2011/DAM 1:2022)
Specifikacija geometrijskih veličin izdelka - Geometrijsko toleriranje - Reference in sistemi referenc - Dopolnilo A1 (ISO 5459:2011/DAM 1:2022)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 5459:2011/oprA1:2022
01-december-2022
Specifikacija geometrijskih veličin izdelka - Geometrijsko toleriranje - Reference in
sistemi referenc - Dopolnilo A1 (ISO 5459:2011/DAM 1:2022)
Geometrical product specifications (GPS) - Geometrical tolerancing - Datums and datum
systems - Amendment 1 (ISO 5459:2011/DAM 1:2022)
Geometrische Produktspezifikation (GPS) - Geometrische Tolerierung - Bezüge und
Bezugssysteme - Änderung 1 (ISO 5459:2011/DAM 1:2022)
Spécification géométrique des produits (GPS) - Tolérancement géométrique -
Références spécifiées et systèmes de références spécifiées - Amendement 1 (ISO
5459:2011/DAM 1:2022)
Ta slovenski standard je istoveten z: EN ISO 5459:2011/prA1
ICS:
17.040.10 Tolerance in ujemi Limits and fits
17.040.40 Specifikacija geometrijskih Geometrical Product
veličin izdelka (GPS) Specification (GPS)
SIST EN ISO 5459:2011/oprA1:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 5459:2011/oprA1:2022
---------------------- Page: 2 ----------------------
SIST EN ISO 5459:2011/oprA1:2022
DRAFT AMENDMENT
ISO 5459:2011/DAM 1
ISO/TC 213 Secretariat: BSI
Voting begins on: Voting terminates on:
2022-10-24 2023-01-16
Geometrical product specifications (GPS) — Geometrical
tolerancing — Datums and datum systems
AMENDMENT 1
Spécification géométrique des produits (GPS) — Tolérancement géométrique — Références spécifiées et
systèmes de références spécifiées
AMENDEMENT 1
ICS: 17.040.10; 01.100.20
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO 5459:2011/DAM 1:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022
---------------------- Page: 3 ----------------------
SIST EN ISO 5459:2011/oprA1:2022
ISO 5459:2011/DAM 1:2022(E)
DRAFT AMENDMENT
ISO 5459:2011/DAM 1
ISO/TC 213 Secretariat: BSI
Voting begins on: Voting terminates on:
Geometrical product specifications (GPS) — Geometrical
tolerancing — Datums and datum systems
AMENDMENT 1
Spécification géométrique des produits (GPS) — Tolérancement géométrique — Références spécifiées et
systèmes de références spécifiées
AMENDEMENT 1
ICS: 17.040.10; 01.100.20
This document is circulated as received from the committee secretariat.
COPYRIGHT PROTECTED DOCUMENT
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2022
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO 5459:2011/DAM 1:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
© ISO 2022 – All rights reserved
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022
---------------------- Page: 4 ----------------------
SIST EN ISO 5459:2011/oprA1:2022
ISO 5459:2011/DAM 1:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, gov
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.