EN 12201-2:2003

Plastics piping systems for water supply - Polyethylene (PE) - Part 2: Pipes

This part of prEN 12201 specifies the characteristics of pipes made from polyethylene (PE) intended for the conveyance of water for human consumption, including raw water prior to treatment. It also specifies the test parameters for the test methods referred to in this standard. In conjunction with other Parts of prEN 12201 it is applicable to PE pipes, their joints and to joints with components of PE and other materials intended to be used under the following conditions: a) a maximum operating pressure, MOP, up to and including 25 bar; b) an operating temperature of 20 °C as a reference temperature.

Kunststoff-Rohrleitungssysteme für die Wasserversorgung - Polyethylen (PE) - Teil 2: Rohre

Diese Norm legt Anforderungen an Rohre aus Polyethylen (PE) fest, die für die Wasserversorgung für den menschlichen Gebrauch sowie für die Fortleitung von Rohrwasser, das zur Aufbereitung zu Trinkwasser verwendet wird, eingesetzt werden. Sie legt auch die Prüfparameter für die Prüfverfahren fest, auf die in dieser Norm verwiesen wird. Zusammen mit den übrigen Teilen der prEN 12201 gilt dieser Teil für Rohre aus PE, deren Verbindungen untereinander sowie mit Rohrleitungsteilen aus PE und anderen Werkstoffen, die unter den folgenden Bedingungen für die Wasserversorgung vorgesehen sind: a) der MOP beträgt nicht mehr als 25 b.

Système de canalisations en plastique pour l'alimentation en eau - Polyéthylène (PE) - Partie 2: Tubes

La présente partie du prEN 12201 spécifie les caractéristiques des tubes en polyéthylène (PE) destinés pour l'alimentation en eau destinée à la consommation humaine, y compris le transport des eaux brutes avant traitement. Elle spécifie également les paramètres d'essai des méthodes d'essai auxquelles la présente norme fait référence. Conjointement aux autres parties du prEN 12201, elle s'applique aux tubes, raccords, robinets PE, à leur assemblage et aux assemblages avec des composants non fabriqués en matières plastiques destinés à être utilisés selon les conditions suivantes: a) une MOP pouvant atteindre jusqu'à 25 bar inclus etc

Cevni sistemi iz polimernih materialov za oskrbo z vodo - Polietilen (PE) - 2. del: Cevi

General Information

• Status: Withdrawn
• Publication Date: 04-Mar-2003
• Withdrawal Date: 06-Sep-2011
• ICS: 23.040.05 - Pipeline and its parts for external sewage systems
• ICS: 23.040.20 - Plastics pipes
• ICS: 91.140.60 - Water supply systems
• ICS: 93.030 - External sewage systems
• Technical Committee: CEN/TC 155 - Plastics piping systems and ducting systems
• Drafting Committee: CEN/TC 155/WG 12 - Systems for water supply and pressure drainage and sewerage - PE, PP (solid wall)
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 07-Sep-2011
• Completion Date: 07-Sep-2011
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Directive: 89/106/EEC - Construction products
• Ref Project: SIST EN 12201-2:2003 - Plastics piping systems for water supply - Polyethylene (PE) - Part 2: Pipes

Relations

• Replaced By: EN 12201-2:2011 - Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes
• Effective Date: 01-Apr-2009

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Cevni sistemi iz polimernih materialov za oskrbo z vodo - Polietilen (PE) - 2. del: CeviKunststoff-Rohrleitungssysteme für die Wasserversorgung - Polyethylen (PE) - Teil 2: RohreSysteme de canalisations en plastique pour l'alimentation en eau - Polyéthylene (PE) - Partie 2: TubesPlastics piping systems for water supply - Polyethylene (PE) - Part 2: Pipes91.140.60Sistemi za oskrbo z vodoWater supply systems23.040.20Cevi iz polimernih materialovPlastics pipesICS:Ta slovenski standard je istoveten z:EN 12201-2:2003SIST EN 12201-2:2003en01-oktober-2003SIST EN 12201-2:2003SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12201-2March 2003ICS 23.040.20; 91.140.60English versionPlastics piping systems for water supply - Polyethylene (PE) -Part 2: PipesSystème de canalisations en plastique pour l'alimentationen eau - Polyéthylène (PE) - Partie 2: TubesKunststoff-Rohrleitungssysteme für die Wasserversorgung- Polyethylen (PE) - Teil 2: RohreThis European Standard was approved by CEN on 4 December 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12201-2:2003 ESIST EN 12201-2:2003

Relationship between PN, MRS, S and SDR.16Bibliography.17SIST EN 12201-2:2003

Plastics piping systems for water supply — Unplasticized poly(vinyl chloride) (PVC-U);— prEN 1796,
Plastics piping systems for water supply with or without pressure — Glass-reinforcedthermosetting plastics (GRP) based on polyester resins (UP).For components which have conformed to the relevant national standard before [DAV], as shown by themanufacturer or by a certification body, the national standard may continue to be applied until the [DAV + 24months].According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard : Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal,Slovakia, Spain, Sweden, Switzerland and the United Kingdom.
1)
to be published as a CEN/TS.SIST EN 12201-2:2003

this standard provides no information as to whether the product may be used without restriction in any of theMember States of the EU or EFTA;b)
it should be noted that, while awaiting the adoption of verifiable European criteria, existing national regulationsconcerning the use and/or the characteristics of this product remain in force.Requirements and test methods for material and components, other than pipes, are specified in EN 12201-1, EN12201-3 and EN 12201-4. Characteristics for fitness of purpose are covered in EN 12201-5 and prCEN/TS 12201-7gives guidance for the assessment of conformity.This Part of this European Standard covers the characteristics of pipes.SIST EN 12201-2:2003

a maximum operating pressure, MOP, up to 25 bar 2);b)
an operating temperature of 20 °C as a reference temperature.NOTE 1For applications operating at constant temperatures greater than 20 °C and up to 40 °C, see annex A of EN 12201-1:2003.This European Standard covers a range of maximum operating pressures and gives requirements concerningcolours and additives.NOTE 2It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account theirparticular requirements and any relevant national guidance or regulations and installation practices or codes.NOTE 3Assessment of the resistance to slow crack growth of the PE pipe compound used for the manufacture of products to thisspecification is required in accordance with Table 2 of EN 12201-1:2003.2 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text, and the publications are listed hereafter. Fordated references, subsequent amendments to or revisions of any of these publications apply to this EuropeanStandard only when incorporated in it by amendment or revision. For undated references the latest edition of thepublication referred to applies (including amendments).EN 728,
Plastics piping and ducting systems — Polyolefin pipes and fittings — Determination of oxidationinduction time.EN 921:1994,
Plastics piping systems — Thermoplastics pipes — Determination of resistance to internal pressureat constant temperature.EN 12201-1:2003,
Plastics piping systems for water supply — Polyethylene (PE) — Part 1: General.EN 12201-5,
Plastics piping systems for water supply — Polyethylene (PE) — Part 5: Fitness for purpose of thesystem.EN ISO 1133:1999,
Plastics — Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate(MVR) of thermoplastics (ISO 1133:1997).prEN ISO 3126:1999,
Plastics piping systems — Plastics piping components — Measurement and determinationof dimensions (ISO/DIS 3126:1999).EN ISO 6259-1:2001,
Thermoplastics pipes — Determination of tensile properties — Part 1: General test method(ISO 6259-1:1997).ISO 4433-1:1997,
Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 1: Immersiontest method.ISO 4433-2:1997,
Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 2: Polyolefinpipes.ISO 6259-3:1997,
Thermoplastics pipes — Determination of tensile properties — Part 3: Polyolefin pipes.
2)1 bar = 105 N/m2SIST EN 12201-2:2003
...