Safety of machinery - Reduction of risks to health resulting from hazardous substances emitted by machinery - Part 1: Principles and specifications for machinery manufacturers (ISO 14123-1:2015)

ISO 14123-1:2015 establishes principles for the control of risks to health resulting from hazardous substances emitted by machinery.
ISO 14123-1:2015 is not applicable to substances that are a hazard to health solely because of their explosive, flammable or radioactive properties or their behaviour at extremes of temperature or pressure.

Sicherheit von Maschinen - Minderung von Gesundheitsrisiken, die auf Gefahrstoffemissionen von Maschinen zurückzuführen sind - Teil 1: Grundsätze und Festlegungen für Maschinenhersteller (ISO 14123-1:2015)

Dieser Teil von ISO 14123 stellt Grundsätze auf für die Überwachung von Gesundheitsrisiken, die auf Gefahrstoffemissionen von Maschinen zurückzuführen sind.
Dieser Teil von ISO 14123 gilt nicht für Gefahrstoffe, die ausschließlich aufgrund von explosiven, entzündlichen oder radioaktiven Eigenschaften oder deren Verhalten bei Temperatur- oder Druckextremen eine Gesundheitsgefährdung darstellen.

Sécurité des machines - Réduction des risques pour la santé résultant de substances dangereuses émises par des machines - Partie 1: Principes et spécifications à l'intention des constructeurs de machines (ISO 14123-1:2015)

ISO 14123-1:2015 établit des principes de maîtrise des risques pour la santé résultant des substances dangereuses émises par des machines.
ISO 14123-1:2015 ne couvre pas les substances constituant un danger pour la santé du seul fait de leur caractère explosif, inflammable, radioactif ou de leurs conditions de température (haute ou basse) ou de pression (haute ou basse).

Varnost strojev - Zmanjšanje zdravstvenega tveganja zaradi nevarnih snovi, ki jih oddajajo stroji - 1. del: Načela in specifikacije za proizvajalce strojev (ISO 14123-1:2015)

Ta evropski standard opisuje načela za obvladovanje zdravstvenih tveganj zaradi nevarnih snovi iz strojev. Ta evropski standard se ne uporablja za snovi, ki so zdravju nevarne izključno zaradi svoje eksplozivnosti, vnetljivosti ali radioaktivnosti oziroma njihovega obnašanja pri skrajni temperaturi ali tlaku.

General Information

Status
Published
Publication Date
10-Nov-2015
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Due Date
11-Nov-2015
Completion Date
11-Nov-2015

RELATIONS

Buy Standard

Standard
EN ISO 14123-1:2016
English language
18 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN ISO 14123-1:2016
01-februar-2016
1DGRPHãþD
SIST EN 626-1:1995+A1:2008

9DUQRVWVWURMHY=PDQMãDQMH]GUDYVWYHQHJDWYHJDQMD]DUDGLQHYDUQLKVQRYLNLMLK

RGGDMDMRVWURMLGHO1DþHODLQVSHFLILNDFLMH]DSURL]YDMDOFHVWURMHY ,62



Safety of machinery - Reduction of risks to health resulting from hazardous substances

emitted by machinery - Part 1: Principles and specifications for machinery manufacturers

(ISO 14123-1:2015)
Sicherheit von Maschinen - Minderung von Gesundheitsrisiken, die auf
Gefahrstoffemissionen von Maschinen zurückzuführen sind - Teil 1: Grundsätze und
Festlegungen für Maschinenhersteller (ISO 14123-1:2015)

Sécurité des machines - Réduction des risques pour la santé résultant de substances

dangereuses émises par des machines - Partie 1: Principes et spécifications à l'intention

des constructeurs de machines (ISO 14123-1:2015)
Ta slovenski standard je istoveten z: EN ISO 14123-1:2015
ICS:
13.100 Varnost pri delu. Industrijska Occupational safety.
higiena Industrial hygiene
13.110 Varnost strojev Safety of machinery
SIST EN ISO 14123-1:2016 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 14123-1:2016
---------------------- Page: 2 ----------------------
SIST EN ISO 14123-1:2016
EN ISO 14123-1
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2015
EUROPÄISCHE NORM
ICS 13.110 Supersedes EN 626-1:1994+A1:2008
English Version
Safety of machinery - Reduction of risks to health resulting
from hazardous substances emitted by machinery - Part 1:
Principles and specifications for machinery manufacturers
(ISO 14123-1:2015)

Sécurité des machines - Réduction des risques pour la Sicherheit von Maschinen - Minderung von

santé résultant de substances dangereuses émises par Gesundheitsrisiken, die auf Gefahrstoffemissionen von

des machines - Partie 1: Principes et spécifications à Maschinen zurückzuführen sind - Teil 1: Grundsätze

l'intention des constructeurs de machines (ISO 14123- und Festlegungen für Maschinenhersteller (ISO 14123-

1:2015) 1:2015)
This European Standard was approved by CEN on 10 October 2015.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,

Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels

© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14123-1:2015 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 14123-1:2016
EN ISO 14123-1:2015 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

Annex ZA (informative) Relationship between this European Standard and the essential

requirements of EU Directive 2006/42/EC aimed to be covered .................................................. 4

---------------------- Page: 4 ----------------------
SIST EN ISO 14123-1:2016
EN ISO 14123-1:2015 (E)
European foreword

This document (EN ISO 14123-1:2015) has been prepared by Technical Committee ISO/TC 199 "Safety

of machinery" in collaboration with Technical Committee CEN/TC 114 “Safety of machinery” the

secretariat of which is held by DIN.

This European Standard shall be given the status of a national standard, either by publication of an

identical text or by endorsement, at the latest by May 2016, and conflicting national standards shall be

withdrawn at the latest by May 2016.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent

rights.
This document supersedes EN 626-1:1994+A1:2008.

This document has been prepared under a mandate given to CEN by the European Commission and the

European Free Trade Association, and supports essential requirements of EU Directive(s).

For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this

document.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the

following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,

Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,

France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,

Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and the United Kingdom.
Endorsement notice

The text of ISO 14123-1:2015 has been approved by CEN as EN ISO 14123-1:2015 without any

modification.
---------------------- Page: 5 ----------------------
SIST EN ISO 14123-1:2016
EN ISO 14123-1:2015 (E)
Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of EU Directive 2006/42/EC aimed to be covered

This European Standard has been prepared under a Commission’s standardisation request M/079 to

provide one voluntary means of conforming to essential requirements of EU Directive 2006/42/EC of

the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive

95/16/EC (OJ L 157, 9.6.2006).

Once this standard is cited in the Official Journal of the European Union under that Directive,

compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of

the scope of this standard, a presumption of conformity with the corresponding essential requirements

of that Directive, and associated EFTA regulations.
Table ZA.1 — Correspondence between this European standard
and Annex I of Directive 2006/42/EC
Essential Requirements of Clause(s) / sub-clause(s)
Remarks / Notes
Directive 2006/42/EC of this EN
1.5.13 Clauses 4 to 8

WARNING 1: Presumption of conformity stays valid only as long as a reference to this European

standard is maintained in the list published in the Official Journal of the European Union. Users of this

standard should consult frequently the latest list published in the Official Journal of the European

Union.

WARNING 2: Other Union legislation may be applicable to the product(s) falling within the scope of this

standard.
---------------------- Page: 6 ----------------------
SIST EN ISO 14123-1:2016
INTERNATIONAL ISO
STANDARD 14123-1
Second edition
2015-10-15
Safety of machinery — Reduction
of risks to health resulting from
hazardous substances emitted by
machinery —
Part 1:
Principles and specifications for
machinery manufacturers
Sécurité des machines — Réduction des risques pour la santé
résultant de substances dangereuses émises par des machines —
Partie 1: Principes et spécifications à l’intention des constructeurs de
machines
Reference number
ISO 14123-1:2015(E)
ISO 2015
---------------------- Page: 7 ----------------------
SIST EN ISO 14123-1:2016
ISO 14123-1:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 14123-1:2016
ISO 14123-1:2015(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Risk assessment .................................................................................................................................................................................................... 1

5 Types of emissions ............................................................................................................................................................................................. 2

5.1 Airborne emissions ............................................................................................................................................................................. 2

5.2 Non-airborne emissions ................................................................................................................................................................. 3

6 Requirements and/or protective measures for elimination and/or reduction of risk ..............4

7 Information for use and maintenance information ......................................................................................................... 5

7.1 Information for use ............................................................................................................................................................................. 5

7.2 Maintenance information .............................................................................................................................................................. 5

8 Verification of safety requirements and/or protective measures ....................................................................6

Annex A (informative) Examples of protective measures for reduction of exposure to

hazardous substances ..................................................................................................................................................................................... 7

Bibliography ................................................................................................................................................................................................................................ 9

© ISO 2015 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 14123-1:2016
ISO 14123-1:2015(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www.iso.org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation on the meaning of ISO specific terms and expressions related to conformity

assessment, as well as information about ISO’s adherence to the WTO principles in the Technical

Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information

The committee responsible for this document is ISO/TC 199, Safety of machinery.

This second edition cancels and replaces the first edition (ISO 14123-1:1998), of which, by taking

ISO 12100 into account, it constitutes a minor revision.

ISO 14123 consists of the following parts, under the general title Safety of machinery — Reduction of

risks to health resulting from hazardous substances emitted by machinery:
— Part 1: Principles and specifications for machinery manufacturers
— Part 2: Methodology leading to verification procedures
iv © ISO 2015 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 14123-1:2016
ISO 14123-1:2015(E)
Introduction
The structure of safety standards in the field of machinery is as follows:

a) type-A standards (basic safety standards) giving basic concepts, principles for design, and general

aspects that can be applied to machinery;

b) type-B standards (generic safety standards) dealing with one safety aspect or one type of

safeguard that can be used across a wide range of machinery:

— type-B1 standards on particular safety aspects (for example, safety distances, surface

temperature, noise);

— type-B2 standards on safeguards (for example, two-hand controls, interlocking devices,

pressure-sensitive devices, guards);

c) type-C standards (machine safety standards) dealing with detailed safety requirements for a

particular machine or group of machines.

This document is a type-B1 standard as stated in ISO 12100. Its primary purpose is to give guidance to

the writers of type-C standards when machines are identified as emitting hazardous substances as a

significant risk. This part of ISO 14123 can also be used as guidance in controlling the risk where there

is no type-C standard for a particular machine.

This document is of relevance, in particular, for the following stakeholder groups representing the

market players with regard to machinery safety:
— machine manufacturers (small, medium and large enterprises);

— health and safety bodies (regulators, accident prevention organizations, market surveillance etc.);

Others can be affected by the level of machinery safety achieved with the means of the document by the

above-mentioned stakeholder groups:
— machine users/employers (small, medium and large enterprises);

— machine users/employees (e.g. trade unions, organizations for people with special needs);

— service providers, e.g. for maintenance (small, medium and large enterprises);
— consumers (in case of machinery intended for use by consumers).

The above-mentioned stakeholder groups have been given the possibility to participate at the drafting

process of this document.

The requirements of this document can be supplemented or modified by a type-C standard.

For machines that are covered by the scope of a type-C standard and that have been designed and built

according to the requirements of that standard, the requirements of that type-C standard take precedence.

© ISO 2015 – All rights reserved v
---------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.