EN ISO 1119:2011

Geometrical product specifications (GPS) - Series of conical tapers and taper angles (ISO 1119:2011)

ISO 1119:2011 provides calculated values for  a series of cones or conical tapers, ranging from 120° to less than 1°, or ratios from 1:0,289 to 1:500, intended for general use in technical engineering.
It applies only to plain conical surfaces, and excludes prismatic pieces, taper threads, bevel gears, etc.

Geometrische Produktspezifikation (GPS) - Reihen von Kegeln und Kegelwinkeln (ISO 1119:2011)

Diese Internationale Norm gibt berechnete Werte für Reihen von Kegeln und Kegelwinkeln, welche sich von
120° bis zu kleiner als 1° erstrecken, oder von Kegelverhältnissen zwischen 1:0,289 und 1:500 an, die für die
allgemeine Verwendung in technischen Zeichnungen vorgesehen sind.
Sie ist nur für einfache Kegelflächen anwendbar und schließt prismatische Teile, Kegelgewinde, Kegelzahnräder,
usw. aus.

Spécification géométrique des produits (GPS) - Série d'angles de cônes et de conicités (ISO 1119:2011)

L'ISO 1119:2011 fournit des valeurs calculées pour les séries d'angle de cônes allant de 120° à moins de 1° et de conicités allant de 1:0,289 à 1:500, à l'usage de la mécanique en général.
Elle est applicable seulement aux cônes lisses et non aux pièces prismatiques, filetages coniques, engrenages coniques, etc.

Specifikacija geometrijskih veličin izdelka - Vrste konusov in njihovi koti (ISO 1119:2011)

Ta evropski standard določa preskusne metode za gibljive in omejeno gibljive obojčne spoje z elastomernimi tesnilnimi elementi, ki se uporabljajo pri podzemnih in nadzemnih cevovodih iz duromernih materialov, ojačenih s steklenimi vlakni (GRP). Standard zajema le metode za preskus tesnjenja in odpornosti proti poškodbam spoja, kadar je izpostavljen določenim kombinacijam prečnega raztezanja (vlečenje), kotnega premikanja (kotni odklon), stiskanja (neporavnanost) pravokotno na os cevi ter notranjega tlaka. Ta evropski standard se uporablja za spoje v tlačnih ali netlačnih uporabah. Ti preskusni postopki se uporabljajo za spoje za cevi in fitinge vseh nazivnih velikosti. Preskusi so primerni za vrednotenje spojev za uporabe, pri katerih se tekočine pretakajo pri temperaturah, določenih v referenčnih standardih.

General Information

• Status: Published
• Publication Date: 14-Dec-2011
• Withdrawal Date: 29-Jun-2012
• ICS: 17.040.01 - Linear and angular measurements in general
• ICS: 17.040.20 - Properties of surfaces
• ICS: 17.040.30 - Measuring instruments
• Technical Committee: CEN/TC 290 - Dimensional and geometrical product specification and verification
• Drafting Committee: CEN/TC 290 - Dimensional and geometrical product specification and verification
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 15-Dec-2011
• Completion Date: 15-Dec-2011
• Ref Project: SIST EN ISO 1119:2012 - Geometrical product specifications (GPS) - Series of conical tapers and taper angles (ISO 1119:2011)

Relations

• Replaces: EN ISO 1119:2002 - Geometrical product specifications (GPS) - Series of conical tapers and taper angles (ISO 1119:1998)
• Effective Date: 28-Dec-2011

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 1119:2012
01-februar-2012
1DGRPHãþD
SIST EN ISO 1119:2004
SIST ISO 1119:2001
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND9UVWHNRQXVRYLQQMLKRYLNRWL,62

Geometrical product specifications (GPS) - Series of conical tapers and taper angles
(ISO 1119:2011)
Geometrische Produktspezifikation (GPS) - Reihen von Regeln und Kegelwinkeln (ISO
1119:2011)
Spécification géométrique des produits (GPS) - Série d'angles de cônes et de conicités
(ISO 1119:2011)
Ta slovenski standard je istoveten z: EN ISO 1119:2011
ICS:
17.040.40 6SHFLILNDFLMDJHRPHWULMVNLK Geometrical Product
YHOLþLQL]GHOND*36 Specification (GPS)
SIST EN ISO 1119:2012 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 1119:2012

---------------------- Page: 2 ----------------------

SIST EN ISO 1119:2012


EUROPEAN STANDARD
EN ISO 1119

NORME EUROPÉENNE

EUROPÄISCHE NORM
December 2011
ICS 17.040.01 Supersedes EN ISO 1119:2002
English Version
Geometrical product specifications (GPS) - Series of conical
tapers and taper angles (ISO 1119:2011)
Spécification géométrique des produits (GPS) - Série Geometrische Produktspezifikation (GPS) - Reihen von
d'angles de cônes et de conicités (ISO 1119:2011) Regeln und Kegelwinkeln (ISO 1119:2011)
This European Standard was approved by CEN on 14 December 2011.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1119:2011: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 1119:2012
EN ISO 1119:2011 (E)
Contents Page
Foreword .3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 1119:2012
EN ISO 1119:2011 (E)
Foreword
This document (EN ISO 1119:2011) has been prepared by Technical Committee ISO/TC 213 "Dimensional
and geometrical product specifications and verification" in collaboration with Technical Committee
CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of which is
held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2012, and conflicting national standards shall be withdrawn at
the latest by June 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 1119:2002.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 1119:2011 has been approved by CEN as a EN ISO 1119:2011 without any modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 1119:2012

---------------------- Page: 6 ----------------------

SIST EN ISO 1119:2012

INTERNATIONAL ISO
STANDARD 1119
Third edition
2011-12-15

Geometrical product specifications
(GPS) — Series of conical tapers and
taper angles
Spécification g
...