EN IEC 60598-2-17:2018
(Main)Luminaires - Part 2-17: Particular requirements - Luminaires for stage lighting, television and film studios (outdoor and indoor)
Luminaires - Part 2-17: Particular requirements - Luminaires for stage lighting, television and film studios (outdoor and indoor)
IEC 60598-2-17:2017 specifies requirements for stage, television, film and photographic studio luminaires (including spot and floodlighting projectors) for use outdoors and indoors, with electric light sources on supply voltages not exceeding 1 000 V. This second edition cancels and replaces the first edition published in 1984 and Amendement 2:1990. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) extension of the applicable scope from light source to electric light source and replacement of "tungsten filament, tubular fluorescent and other discharge lamps" with "electric light source" in 17.1. b) consideration of the fact that there are many LED luminaires with non-replaceable light source, and light source without a glass bulb, or with low operation temperature: the applicable scope of relevant clauses therefore only applies to replaceable light source luminaires with a glass bulb lamp, or with high surface temperature.
Leuchten - Teil 2-17: Besondere Anforderungen - Leuchten für Bühnenbeleuchtung, Fernseh- und Film-Studios (außen und innen)
Luminaires - Partie 2-17: Exigences particulières - Luminaires pour éclairage des scènes de théâtre, pour prises de vues de télévision et de cinéma (à l'extérieur et à l'intérieur)
L'IEC 60598-2-17:2017 détaille les exigences applicables aux luminaires pour les scènes de théâtre, pour les prises de vues de télévision, de cinéma et de photographie (y compris des projecteurs à faisceaux intensifs et extensifs) à utiliser, à l’extérieur et à l’intérieur, avec des sources électriques lumineuses pour des tensions ne dépassant pas 1 000 V. Cette deuxième édition annule et remplace la première édition parue en 1984 et l’Amendement 2:1990. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: a) Extension du domaine d'application de la source lumineuse à la source électrique lumineuse et remplacement de “lampes à filament de tungstène, lampes tubulaires fluorescentes et autres lampes à décharge” par “source électrique lumineuse” en 17.1. b) Prise en considération du fait qu'il existe de nombreux luminaires à LED avec une source lumineuse non remplaçable et une source lumineuse sans ampoule en verre, ou avec un fonctionnement à basse température: le domaine d'application des articles correspondants est donc réduit aux luminaires avec source lumineuse remplaçable, équipés d'une lampe à ampoule en verre, ou avec une température de surface élevée.
Svetilke - 2-17. del: Posebne zahteve - Svetilke za razsvetljavo odrov, televizijskih in filmskih studiev (zunanja in notranja uporaba) (IEC 60598-2-17:2017)
Ta del IEC 60598-2 določa zahteve za sijalke za oder, televizijo, filmski in fotografski studio (vključno s točkovnimi in reflektorskimi projektorji) za uporabo zunaj in znotraj, z električnimi svetlobnimi viri na napajalni napetostih, ki ne presegajo 1 000 V.
OPOMBA Obesa (streme) je del sijalke. Podporne naprave kot so trinožniki, teleskopske roke in vzmetenja niso deli sijalke. Kjer je to potrebno, so bremena vgrajena ali nameščena ločeno od sijalk.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2018
1DGRPHãþD
SIST EN 60598-2-17:1995
Svetilke - 2-17. del: Posebne zahteve - Svetilke za razsvetljavo odrov, televizijskih
in filmskih studiev (zunanja in notranja uporaba) (IEC 60598-2-17:2017)
Luminaires - Part 2-17: Particular requirements - Luminaires for stage lighting, television
and film studios (outdoor and indoor) (IEC 60598-2-17:2017)
Leuchten - Teil 2: Besondere Anforderungen - Hauptabschnitt 17: Leuchten für Bühnen,
Fernseh-, Film und Fotostudios (Außen und Innen) (IEC 60598-2-17:2017)
Luminaires - Partie 2-17: Règles particulières - Luminaires pour l'éclairage des scènes
de théâtre, des studios de télévision, de cinéma et de photographie (à l'extérieur et à
l'intérieur) (IEC 60598-2-17:2017)
Ta slovenski standard je istoveten z: EN IEC 60598-2-17:2018
ICS:
29.140.40 Svetila Luminaires
97.200.10 Gledališka, odrska in Theatre, stage and studio
studijska oprema ter delovne equipment
postaje
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 60598-2-17
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2018
ICS 29.140.40; 97.200.10 Supersedes EN 60598-2-17:1989
English Version
Luminaires - Part 2-17: Particular requirements - Luminaires for
stage lighting, television and film studios (outdoor and indoor)
(IEC 60598-2-17:2017)
Luminaires - Partie 2-17: Exigences particulières - Leuchten - Teil 2-17: Besondere Anforderungen - Leuchten
Luminaires pour éclairage des scènes de théâtre, pour für Bühnenbeleuchtung, Fernseh- und Film-Studios (außen
prises de vues de télévision et de cinéma (à l'extérieur et à und innen)
l'intérieur) (IEC 60598-2-17:2017)
(IEC 60598-2-17:2017)
This European Standard was approved by CENELEC on 2017-07-04. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60598-2-17:2018 E
European foreword
The text of document 34D/1275/FDIS, future edition 2 of IEC 60598-2-17, prepared by SC 34D
"Luminaires" of IEC/TC 34 "Lamps and related equipment" was submitted to the IEC-CENELEC
parallel vote and approved by CENELEC as EN IEC 60598-2-17:2018.
The following dates are fixed:
• latest date by which the document has to be implemented at (dop) 2018-09-23
national level by publication of an identical national
standard or by endorsement
• latest date by which the national standards conflicting with (dow) 2021-03-23
the document have to be withdrawn
This document supersedes EN 60598-2-17:1989.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZZ, which is an integral part of this
document.
Endorsement notice
The text of the International Standard IEC 60598-2-17:2017 was approved by CENELEC as a
European Standard without any modification.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is
available here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60598-1 2014 Luminaires - Part 1: General EN 60598-1 2015
requirements and tests (mod)
+ A1 2017 + A1 2018
Annex ZZ
(informative)
Relationship between this European Standard and the safety objectives of
Directive 2014/35/EU [2014 OJ L96] aimed to be covered
This European Standard has been prepared under a Commission’s standardization request relating to
harmonized standards in the field of the Low Voltage Directive, M/511, to provide one voluntary means
of conforming to safety objectives of Directive 2014/35/EU of the European Parliament and of the
Council of 26 February 2014 on the harmonization of the laws of the Member States relating to the
making available on the market of electrical equipment designed for use within certain voltage limits
[2014 OJ L96].
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZZ.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding safety objectives of
that Directive, and associated EFTA regulations.
Table ZZ.1 – Correspondence between this European Standard and
Annex I of Directive 2014/35/EU [2014 OJ L96]
Safety objectives of Clause(s) / sub-clause(s)
Remarks / Notes
Directive 2014/35/EU of this EN
1. General conditions
a) the essential characteristics, 17.6
the recognition and observance
of which will ensure that
electrical equipment will be
used safely and in applications
for which it was made, shall be
marked on the electrical
equipment, or, if this is not
possible, on an accompanying
document;
b) the electrical equipment, All
together with its component
parts, shall be made in such a
way as to ensure that it can be
safely and properly assembled
and connected;
c) the electrical equipment shall See item 2 and 3 of this table
be so designed and
manufactured as to ensure that
protection against the hazards
set out in points 2 and 3 is
assured, providing that the
equipment is used in
applications for which it was
made and is adequately
maintained.
Safety objectives of Clause(s) / sub-clause(s)
Remarks / Notes
Directive 2014/35/EU of this EN
2. Protection against hazards
arising from the electrical
equipment
Measures of a technical nature
shall be laid down in
accordance with point 1, in
order to ensure that:
a) persons and domestic 17.7
animals are adequately
17.8
protected against the danger of
17.9
physical injury or other harm
17.10
which might be caused by direct
or indirect contact;
17.11
17.12
17.15
b) temperatures, arcs or 17.7 EMF is not covered
radiation which would cause a
17.8
danger, are not produced;
17.13
17.15
c) persons, domestic animals 17.7
and property are adequately
17.8
protected against non-electrical
17.15
dangers caused by the electrical
equipment which are revealed
by experience;
d) the insulation is suitable for 17.8
foreseeable conditions.
17.14
17.15
3. Protection against hazards
which may be caused by
external influences on the
electrical equipment
Technical measures shall be
laid down in accordance with
point 1, in order to ensure that
the electrical equipment:
a) meets the expected 17.6
mechanical requirements in
17.7
such a way that persons,
domestic animals and property
are not endangered;
b) is resistant to non- 17.14
mechanical influences in
17.16
expected environmental
conditions, in such a way that
persons, domestic animals and
property are not endangered;
Safety objectives of Clause(s) / sub-clause(s)
Remarks / Notes
Directive 2014/35/EU of this EN
c) does not endanger persons, 17.7
domestic animals and property
17.13
in foreseeable conditions of
17.16
overload.
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
IEC 60598-2-17 ®
Edition 2.0 2017-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Luminaires –
Part 2-17: Particular requirements – Luminaires for stage lighting, television and
film studios (outdoor and indoor)
Luminaires –
Partie 2-17: Exigences particulières – Luminaires pour éclairage des scènes de
théâtre, pour prises de vues de télévision et de cinéma (à l’extérieur et à
l’intérieur)
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.140.40; 97.200.10 ISBN 978-2-8322-4418-0
– 2 – IEC 60598-2-17:2017 © IEC 2017
CONTENTS
FOREWORD . 3
17.1 Scope . 5
17.2 Normative references . 5
17.3 Terms and definitions . 5
17.4 General test requirements . 5
17.5 Classification of luminaires . 5
17.6 Marking . 5
17.7 Construction . 6
17.8 Creepage distances and clearances . 8
17.9 Provisions for earthing . 8
17.10 Terminals . 8
17.11 External and internal wiring . 8
17.12 Protection against electric shock . 8
17.13 Endurance tests and thermal tests . 8
17.14 Resistance to dust, solid objects and moisture . 9
17.15 Insulation resistance, electric strength,touch current and protective conductor
current . 9
17.16 Resistance to heat, fire and tracking . 9
IEC 60598-2-17:2017 © IEC 2017 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
LUMINAIRES –
Part 2-17: Particular requirements – Luminaires for stage lighting,
television and film studios (outdoor and indoor)
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in
addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. Inte
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.