iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 61000-5-5:1996

(Main)

Electromagnetic compatibility (EMC) - Part 5: Installation and mitigation guidelines - Section 5: Specification of protective devices for HEMP conducted disturbance

Electromagnetic compatibility (EMC) - Part 5: Installation and mitigation guidelines - Section 5: Specification of protective devices for HEMP conducted disturbance

This part of 61000-5 defines how protective devices for conducted disturbance proposed for HEMP protection shall be specified. It is intended to be used for the harmonization of existing or future specifications issued by protective device manufacturers, electronic equipment manufacturers, administrations and other ultimate buyers. Performance requirements shall be given in future IEC documents. This section covers protective devices currently being used for protection against induced HEMP transients on signal and low voltage power lines (nominal voltage up to 1 kV a.c.). General information can be applied also to high voltage lines. However, in these cases, the additional requirements for the protection levels of existing lightning arresters (especially gapless MO-arresters) are under consideration.

Elektromagnetische Verträglichkeit (EMV) - Teil 5: Installationsrichtlinien und Abhilfemaßnahmen - Hauptabschnitt 5: Festlegung von Schutzeinrichtungen gegen leitungsgeführte HEMP-Störgrößen

Compatibilité électromagnétique (CEM) - Partie 5: Guides d'installation et d'atténuation - Section 5: Spécification des dispositifs de protection pour perturbations conduites IEMN-HA

La présente section de la CEI 61000-5 définit comment les dispositifs de protection contre les perturbations conduites proposés pour la protection IEMN doivent être spécifiés. Elle a pour but d'harmoniser les spécifications, existantes ou à venir, issues des fabricants de protections, des fabricants d'équipements électroniques, des administrations et autres exploitants. Les exigences de performances seront données dans des documents futurs de la CEI. Cette section couvre les protections utilisées couramment pour la protection contre les transitoires induits par l'IEMN-HA sur les acccès signaux et les accès énergie basse tension (tension nominale) jusqu'à 1 kV alternatif). Les généralités peuvent aussi être appliquées à des accès haute tension; cependant, dans ce cas, les exigences additionnelles pour les niveaux de protection des parafoudres (spécialement les parafoudres à oxyde métallique) sont à l'étude.

Electromagnetic compatibility (EMC) - Part 5: Installationand mitigation guidelines - Section 5: Specification of protective devices for HEMP conducted disturbance - Basic EMC publication (IEC 1000-5-5:1996)

General Information

Status
Published
Publication Date
07-May-1996
Withdrawal Date
30-Nov-1996
ICS
33.100 - Electromagnetic compatibility (EMC)
Technical Committee
CLC/TC 210 - Electromagnetic Compatibility (EMC)
Drafting Committee
IEC/SC 77C - IEC_SC_77C
Parallel Committee
IEC/SC 77C - IEC_SC_77C
Current Stage
6060 - Document made available - Publishing
Start Date
08-May-1996
Completion Date
08-May-1996
Directive
2004/108/EC - Directive 2004/108/EC of the European Parliament and of the Council of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility and repealing Directive 89/336/EEC
2004/108/EU - DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility and repealing Directive 89/336/EEC
2014/30/EU - Directive 2014/30/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to electromagnetic compatibility (recast)
89/336/EEC - Electromagnetic compatibility (EMC)
Mandate
M/490 - Standardisation mandate to the European Standardisation Organisations (ESOs) to support European Smart Grid deployment
Ref Project
SIST EN 61000-5-5:1997 - Electromagnetic compatibility (EMC) -- Part 5: Installation and mitigation guidelines -- Section 5: Specification of protective devices for HEMP conducted disturbance

Buy Standard

EN 61000-5-5:1997EN 61000-5-5:1997
PreviousNext
Standard
EN 61000-5-5:1997
English language
39 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61000-5-5:1997
01-marec-1997
Electromagnetic compatibility (EMC) - Part 5: Installationand mitigation guidelines
- Section 5: Specification of protective devices for HEMP conducted disturbance -
Basic EMC publication (IEC 1000-5-5:1996)
Electromagnetic compatibility (EMC) -- Part 5: Installation and mitigation guidelines --
Section 5: Specification of protective devices for HEMP conducted disturbance
Elektromagnetische Verträglichkeit (EMV) -- Teil 5: Installationsrichtlinien und
Abhilfemaßnahmen -- Hauptabschnitt 5: Festlegung von Schutzeinrichtungen gegen
leitungsgeführte HEMP-Störgrößen
Compatibilité électromagnétique (CEM) -- Partie 5: Guides d'installation et d'atténuation -
- Section 5: Spécification des dispositifs de protection pour perturbations conduites IEMN
-HA
Ta slovenski standard je istoveten z: EN 61000-5-5:1996
ICS:
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
SIST EN 61000-5-5:1997 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61000-5-5:1997

---------------------- Page: 2 ----------------------

SIST EN 61000-5-5:1997

---------------------- Page: 3 ----------------------

SIST EN 61000-5-5:1997

---------------------- Page: 4 ----------------------

SIST EN 61000-5-5:1997

---------------------- Page: 5 ----------------------

SIST EN 61000-5-5:1997

---------------------- Page: 6 ----------------------

SIST EN 61000-5-5:1997

---------------------- Page: 7 ----------------------

SIST EN 61000-5-5:1997

---------------------- Page: 8 ----------------------

SIST EN 61000-5-5:1997

---------------------- Page: 9 ----------------------

SIST EN 61000-5-5:1997

---------------------- Page: 10 ----------------------

SIST EN 61000-5-5:1997

---------------------- Page: 11 ----------------------

SIST EN 61000-5-5:1997

---------------------- Page: 12 ----------------------

SIST EN 61000-5-5:1997

---------------------- Page: 13 ----------------------

SIST EN 61000-5-5:1997

---------------------- Page: 14 ----------------------

SIST EN 61000-5-5:1997

---------------------- Pa
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN 61000-4-16:2016(Main)
Electromagnetic compatibility (EMC) - Part 4-16: Testing and measurement techniques - Test for immunity to conducted, common mode disturbances in the frequency range 0 Hz to 150 kHz
SIST EN 61000-4-16:2016

IEC 61000-4-16:2015 is available as IEC 61000-4-16:2015 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC 61000-4-16:2015 relates to the immunity requirements and test methods for electrical and electronic equipment to conducted, common mode disturbances in the range d.c. to 150 kHz. The object of this standard is to establish a common and reproducible basis for testing electrical and electronic equipment with the application of common mode disturbances to power supply, control, signal and communication ports. It has the status of a basic EMC publication in accordance with IEC Guide 107. This second edition cancels and replaces the first edition published in 1998, Amendment 1:2001 and Amendment 2:2009. This edition constitutes a technical revision.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 61000-2-9:1996(Main)
Electromagnetic compatibility (EMC) - Part 2: Environment - Section 9: Description of HEMP environment - Radiated disturbance
SIST EN 61000-2-9:1997

This section of IEC 61000-2 defines the high-altitude electromagnetic pulse (HEMP) environment that is one of the consequences of a high-altitude nuclear explosion. Those dealing with this subject consider two cases: - high-altitude nuclear explosions; - low-altitude nuclear explosions. For civil systems, the most important case is the high-altitude nuclear explosion. In this case, the other effects of the nuclear explosion: blast, ground shock, thermal and nuclear ionizing radiation are not present at the ground level. However the electromagnetic pulse associated with the explosion may cause disruption of, and damage to, communication, electronic and electric power systems thereby upsetting the stability of modern society. The object of this standard is to establish a common reference for the HEMP environment in order to select realistic stresses to apply to victim equipment for evaluating their performance.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60437:2024(Main)
Radio interference test on high-voltage insulators
SIST EN IEC 60437:2024

IEC 60437:2023 specifies the procedure for a radio interference (RI) test carried out in a laboratory on clean and dry insulators at a frequency of 0,5 MHz or 1 MHz or, alternatively, at other frequencies between 0,5 MHz and 2 MHz. This document applies to insulators for use on AC or DC overhead power lines and overhead traction lines with a nominal voltage greater than 1 000 V. This third edition cancels and replaces the second edition published in 1997. This third edition cancels and replaces the second edition published in 1997. This edition includes the following significant technical changes with respect to the previous edition: a) Composite station post and composite hollow core station post insulators have been included; b) All paragraphs of Samples test were actualized; c) Sample test fast procedure was introduced.

  • Draft
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61800-3:2023(Main)
Adjustable speed electrical power drive systems - Part 3: EMC requirements and specific test methods for PDS and machine tools
SIST EN IEC 61800-3:2024

IEC 61800-3:2022 specifies electromagnetic compatibility (EMC) requirements for adjustable speed power drive systems (PDSs) and machine tools (MTs). A PDS is an AC or DC motor drive including an electronic converter. Requirements are stated for AC and DC PDSs and MTs with input and/or output voltages (line-to-line voltage), up to 35 kV AC RMS. This document applies to equipment of all power ratings. As a product EMC standard, this document can be used for the assessment of PDS and MT. It can also be used for the assessment of complete drive modules (CDM) or basic drive modules (BDM). Traction applications and electric vehicles are excluded. Equipment which is defined as group 2 in CISPR 11:2015 is excluded. This document does not give requirements for the electrical machine which converts power between the electrical and mechanical forms within the PDS. Requirements for rotating electrical machines are covered by the IEC 60034 series. In this document, the term "motor" is used to describe the electrical machine, whether rotary or linear, and regardless of the direction of power flow. This document is applicable to BDMs, CDMs, PDSs and MTs with or without radio function. However, this document does not specify any radio transmission and reception requirements. This document defines the minimum requirements for emission and immunity in the frequency range from 0 Hz to 400 GHz. Tests are not required in frequency ranges where no requirements are specified. This fourth edition cancels and replaces the third edition published in 2017. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
extension of the scope to machine tools with one or more embedded PDS;
extension of the frequency range for radiated immunity tests to 6 GHz;
general updates in the normative part and the informative annexes.

  • Standard
    133 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 62153-4-7:2021(Main)
Metallic cables and other passive components test methods - Part 4-7: Electromagnetic compatibility (EMC) -Test method for measuring of transfer impedance ZT and screening attenuation aS or coupling attenuation aC of connectors and assemblies - Triaxial tube in tube method
SIST EN IEC 62153-4-7:2021

This part of IEC 62153 deals with the triaxial tube in tube method. This triaxial method is suitable to determine the surface transfer impedance and/or screening attenuation and coupling attenuation of mated screened connectors (including the connection between cable and connector) and cable assemblies. This method could also be extended to determine the transfer impedance, coupling or screening attenuation of balanced or multipin connectors and multicore cable assemblies. For the measurement of transfer impedance and screening- or coupling attenuation, only one test set-up is needed.

  • Standard
    61 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61326-2-1:2021(Main)
Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-1: Particular requirements - Test configurations, operational conditions and performance criteria for sensitive test and measurement equipment for EMC unprotected applications
SIST EN IEC 61326-2-1:2021

IEC 61326-2-1:2020 is available as IEC 61326-2-1:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61326:2020 specifies more detailed test configurations, operational conditions and performance criteria for equipment with test and measurement circuits (internal or, external to the equipment, or both) that are not EMC protected for operational and/or functional reasons, as specified by the manufacturer. The manufacturer specifies the environment for which the product is intended to be used and selects the appropriate test level specifications of IEC 61326-1:2020.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61326-2-5:2021(Main)
Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-5: Particular requirements - Test configurations, operational conditions and performance criteria for field devices with field bus interfaces according to IEC 61784-1
SIST EN IEC 61326-2-5:2021

IEC 61326-2-5:2020 is available as IEC 61326-2-5:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61326-2-5:2020 treats the particular features for EMC testing of field devices with field bus interfaces. This part of IEC 61326 covers only the field bus interface of the equipment. This part refers only to field devices intended for use in process control and process measuring. In this document, field devices with interfaces according to IEC 61784-1:2019, CP 3/2 and CP 1/1 as defined in IEC 61784 are covered. Other field bus interfaces may be included in future editions of this document.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61326-2-2:2021(Main)
Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-2: Particular requirements - Test configurations, operational conditions and performance criteria for portable testing, measuring and monitoring equipment used in low-voltage distribution systems
SIST EN IEC 61326-2-2:2021

IEC 61326-2-2:2020 is available as IEC 61326-2-2:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61326-2-2:2020 specifies more detailed test configurations, operational conditions and performance criteria for equipment covered by Annex A of IEC 61326-1:2020 which is: - used for testing, measuring or monitoring of protective measures in low-voltage distribution systems, and; - powered by battery and/or from the circuit measured, and - portable. Examples of such EUTs include, but are not limited to, voltage detectors, insulation testers, earth continuity testers, earth resistance testers, leakage current clamps, loop impedance testers, “residual-current-device-testers” (RCD-testers) and phase sequence testers as defined in IEC 61557 (all parts).

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61326-2-4:2021(Main)
Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-4: Particular requirements - Test configurations, operational conditions and performance criteria for insulation monitoring devices according to IEC 61557-8 and for equipment for insulation fault location according to IEC 61557-9
SIST EN IEC 61326-2-4:2021

IEC 61326-2-4:2020 is available as IEC 61326-2-4:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61326-2-4:2020 specifies more detailed test configurations, operational conditions and performance criteria than IEC 61326-1 for equipment for - insulation monitoring according to IEC 61557-8; - insulation fault location according to IEC 61557-9. This applies to insulation monitoring devices and for equipment for insulation fault location systems permanently or semi-permanently connected to the distribution system.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61326-1:2021(Main)
Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 1: General requirements
SIST EN IEC 61326-1:2021

IEC 61326-1:2020 is available as IEC 61326-1:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61326:2020 specifies requirements for immunity and emissions regarding electro¬magnetic compatibility (EMC) for electrical equipment, operating from a supply or battery of less than 1 000 V AC or 1 500 V DC or from the circuit being measured. Equipment intended for professional, industrial-process, industrial-manufacturing and educational use is covered by this part. It includes equipment and computing devices for - measurement and test; - control; - LABORATORY use; - accessories intended for use with the above (such as sample handling equipment), intended to be used in industrial and non-industrial locations.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day