Automatic electrical controls - Part 2-6: Particular requirements for automatic electrical pressure sensing controls including mechanical requirements

IEC 60730-2-6:2015(E) applies to automatic electrical pressure sensing controls with a minimum gauge pressure rating of -60 kPa and a maximum gauge pressure rating of 4,2 MPa, for use in, on or in association with, equipment. The equipment may use electricity, gas, oil, solid fuel, solar thermal energy, etc. or a combination thereof. This standard is also applicable to individual pressure sensing controls utilized as part of a control system or pressure sensing controls which are mechanically integral with multi-functional controls having non-electrical outputs. Automatic electrical pressure sensing controls for equipment used by the public, such as equipment intended to be used by laymen in shops, in light industry and on farms, are within the scope of this standard. This standard does not apply to pressure sensing controls intended exclusively for industrial process applications unless explicitly mentioned in the relevant equipment standard. This standard applies to inherent safety, operating values, operating sequences where such are associated with equipment protection, and to the testing of automatic electrical pressure sensing controls used in, on or in association with equipment. This standard is also applicable to the functional safety of low complexity safety related pressure sensing controls and systems. This standard is also applicable to pressure sensing controls for appliances within the scope of IEC 60335-1. This third edition cancels and replaces the second edition published in 2007. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - aligns the text with IEC 60730-1, Edition 5; - modifies requirements for Class B control function (H.27.1.2.2); - modifies requirements for Class C control function (H.27.1.2.3) and - modifies requirements for faults during lock-out or safety- shut-down. Key words: sensing controls, control systems, pressure sensing

Automatische elektrische Regel- und Steuergeräte - Teil 2-6: Besondere Anforderungen an automatische elektrische Druckregel- und Steuergeräte einschließlich mechanischer Anforderungen

Dispositifs de commande électrique automatiques - Partie 2-6: Exigences particulières pour les dispositifs de commande électrique automatiques sensibles à la pression y compris les exigences mécaniques

IEC 60730-2-6:2015 s'applique aux dispositifs de commande électrique automatiques sensibles à la pression avec des caractéristiques assignées de pression minimales de -60 kPa et des caractéristiques assignées de pression maximales de 4,2 Mpa, destinés à être utilisés dans, sur ou avec des matériels. Les matériels peuvent utiliser l'électricité, le gaz, le pétrole, des combustibles solides, l'énergie thermique solaire, etc. ou une combinaison de ces sources d’énergie. La présente norme s’applique également aux dispositifs de commande sensibles à la pression individuels utilisés comme partie d'un système de commande ou comme dispositifs de commande sensibles à la pression intégrés mécaniquement dans des dispositifs de commande multifonctions ayant des sorties non électriques. Les dispositifs de commande électrique automatiques sensibles à la pression pour matériels utilisés par le public, par exemple les matériels destinés à être utilisés par des personnes inexpérimentées dans les magasins, l’industrie légère et dans les fermes, relèvent du domaine d’application de la présente norme. La présente norme ne s'applique pas aux dispositifs de commande sensibles à la pression prévus exclusivement pour des applications industrielles, sauf mention contraire dans la norme de matériel appropriée. La présente norme s’applique à la sécurité intrinsèque, aux valeurs de fonctionnement et aux séquences de fonctionnement dans la mesure où elles interviennent dans la protection des matériels, ainsi qu’aux essais des dispositifs de commande électrique automatiques sensibles à la pression utilisés dans, sur ou avec des matériels. La présente norme s’applique également aux systèmes et dispositifs de commande sensibles à la pression de sécurité fonctionnelle et de sécurité peu complexe. La présente norme s'applique également aux dispositifs de commande sensibles à la pression pour appareils d’utilisation faisant partie du domaine d'application de l’IEC 60335-1. Cette troisième édition annule et remplace la deuxième édition parue en 2007. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: - alignement du texte de cette édition sur celui de l’IEC 60730-1, Édition 5; - modification des exigences de la fonction de commande de classe B (H.27.1.2.2); - modification des exigences de la fonction de commande de classe C (H.27.1.2.3); - modification des exigences relatives aux pannes pendant le verrouillage ou l’arrêt de sécurité. La présente partie 2 est destinée à être utilisée conjointement avec l’IEC 60730-1:2013 Mots clés: commande sensibles, système de commande, sensibles à la pression

Avtomatske električne krmilne naprave za uporabo v gospodinjstvu in za podobno uporabo - 2-6. del: Posebne zahteve za avtomatske električne, na tlak občutljive naprave, vključno z mehanskimi zahtevami

Ta del standarda IEC 60730 se uporablja za avtomatske električne, na tlak občutljive naprave z najmanjšo stopnjo tlaka v merilniku –60 kPa in največjo stopnjo tlaka v merilniku 4,2 MPa, za uporabo v/na opremi ali v povezavi z njo. Za opremo se lahko samostojno ali v kombinaciji uporabljajo elektrika, plin, nafta, trdno gorivo, sončna toplotna energija itd.
OPOMBA: Beseda »oprema« v tem standardu vključuje »naprave« in »kontrolni sistem«. Ta standard se uporablja tudi za posamezne na tlak občutljive naprave, ki se uporabljajo kot del kontrolnega sistema, ali na tlak občutljive naprave, ki so mehansko integrirane v večfunkcijske naprave brez električnih izhodov.
Področje uporabe tega standarda zajema avtomatske električne, na tlak občutljive naprave za opremo za javno uporabo, kot je na primer oprema, namenjena za laično uporabo v trgovinah, lahki industriji in na kmetijah.
Ta standard se ne uporablja za na tlak občutljive naprave, namenjene izključno za industrijsko uporabo, razen če ni to izrecno navedeno v ustreznem standardu za opremo.

General Information

Status
Published
Publication Date
25-Feb-2016
Withdrawal Date
25-Feb-2019
Current Stage
6060 - Document made available - Publishing
Start Date
26-Feb-2016
Completion Date
26-Feb-2016

Relations

Buy Standard

Standard
EN 60730-2-6:2016
English language
35 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-april-2016
1DGRPHãþD
SIST EN 60730-2-6:2009
$YWRPDWVNHHOHNWULþQHNUPLOQHQDSUDYH]DXSRUDERYJRVSRGLQMVWYXLQ]DSRGREQR
XSRUDERGHO3RVHEQH]DKWHYH]DDYWRPDWVNHHOHNWULþQHQDWODNREþXWOMLYH
QDSUDYHYNOMXþQR]PHKDQVNLPL]DKWHYDPL
Automatic electrical controls - Part 2-6: Particular requirements for automatic electrical
pressure sensing controls including mechanical requirements
Automatische elektrische Regel- und Steuergeräte für den Hausgebrauch und ähnliche
Anwendungen - Teil 2-6: Besondere Anforderungen an automatische elektrische
Druckregel- und Steuergeräte einschließlich mechanischer Anforderungen
Dispositifs de commande électrique automatiques à usage domestique et analogue -
Partie 2-6: Règles particulières pour les dispositifs de commande électrique
automatiques sensibles à la pression y compris les exigences mécaniques
Ta slovenski standard je istoveten z: EN 60730-2-6:2016
ICS:
97.120 Avtomatske krmilne naprave Automatic controls for
za dom household use
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 60730-2-6

NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2016
ICS 97.120 Supersedes EN 60730-2-6:2008
English Version
Automatic electrical controls - Part 2-6: Particular requirements
for automatic electrical pressure sensing controls including
mechanical requirements
(IEC 60730-2-6:2015)
Dispositifs de commande électrique automatiques - Automatische elektrische Regel- und Steuergeräte -
Partie 2-6: Exigences particulières pour les dispositifs de Teil 2-6: Besondere Anforderungen an automatische
commande électrique automatiques sensibles à la pression elektrische Druckregel- und Steuergeräte einschließlich
y compris les exigences mécaniques mechanischer Anforderungen
(IEC 60730-2-6:2015) (IEC 60730-2-6:2015)
This European Standard was approved by CENELEC on 2015-05-27. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 60730-2-6:2016 E
European foreword
The text of document 72/980/FDIS, future edition 3 of IEC 60730-2-6, prepared by IEC/TC 72
"Automatic electrical controls" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 60730-2-6:2016.
The following dates are fixed:
(dop) 2016-08-26
• latest date by which the document has to be implemented at
national level by publication of an identical national
standard or by endorsement
(dow) 2019-02-26
• latest date by which the national standards conflicting with
the document have to be withdrawn

This document supersedes EN 60730-2-6:2008.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
This standard covers the Principle Elements of the Safety Objectives for Electrical Equipment
Designed for Use within Certain Voltage Limits (LVD - 2006/95/EC).
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive 2004/108/EC, see informative Annex ZZ, which is an integral
part of this document.
Endorsement notice
The text of the International Standard IEC 60730-2-6:2015 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated :
IEC 60079 NOTE Harmonized in EN 60079 series (modified).

- 3 - EN 60730-2-6:2016
Annex ZZ
(informative)
Coverage of Essential Requirements of EU Directives
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and within its scope the standard covers all
relevant essential requirements as given in Article 1 of Annex I of the EU Directive EMC
(2004/108/EC).
Compliance with this standard provides one means of conformity with the specified essential
requirements of the Directive concerned.
WARNING: Other requirements and other EU Directives may be applicable to the products falling
within the scope of this standard.
___________
IEC 60730-2-6 ®
Edition 3.0 2015-04
INTERNATIONAL
STANDARD
Automatic electrical controls –

Part 2-6: Particular requirements for automatic electrical pressure sensing

controls including mechanical requirements

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 97.120 ISBN 978-2-8322-2587-5

– 2 – IEC 60730-2-6 © IEC 2015
CONTENTS
FOREWORD . 4
1 Scope and normative references . 7
2 Terms and definitions . 8
3 General requirements . 9
4 General notes on tests . 10
5 Rating. 10
6 Classification . 10
7 Information . 11
8 Protection against electric shock . 11
9 Provision for protective earthing . 11
10 Terminals and terminations . 11
11 Constructional requirements . 12
12 Moisture and dust resistance . 14
13 Electric strength and insulation resistance . 14
14 Heating . 14
15 Manufacturing deviation and drift . 14
16 Environmental stress . 15
17 Endurance . 15
18 Mechanical strength . 16
19 Threaded parts and connections . 17
20 Creepage distances, clearances and distances through solid insulation . 17
21 Resistance to heat, fire and tracking . 17
22 Resistance to corrosion . 18
23 Electromagnetic compatibility (EMC) requirements – Emission . 18
24 Components . 18
25 Normal operation . 18
26 Electromagnetic compatibility (EMC) requirements – Immunity . 18
27 Abnormal operation . 18
28 Guidance on the use of electronic disconnection . 18
Annexes . 19
Annex H (normative) Requirements for electronic controls . 20
Annex AA (normative) Number of cycles . 27
AA.1 Number of cycles for independently mounted controls . 27
AA.2 Cycling rate for independently mounted controls . 27
Annex BB (informative) Stainless steel for bellows, bourdon tubes or similar elements . 28
Annex CC (informative)  Deviation and drift requirements for pressure operating

controls . 31
Bibliography . 32

IEC 60730-2-6 © IEC 2015 – 3 –
Table 1 (7.2 of edition 3) – Required information and methods of providing information . 11
Table H.101 – Compliance criteria . 22
Table BB.1 – Stainless steel for bellows, bourdon tubes or similar elements (1 of 3) . 28

– 4 – IEC 60730-2-6 © IEC 2015
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
AUTOMATIC ELECTRICAL CONTROLS –

Part 2-6: Particular requirements for automatic electrical
pressure sensing controls including mechanical requirements

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents inc
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.