EN 62211:2004
(Main)Inductive components - Reliability management
Inductive components - Reliability management
Sets up a broad basis of electric and mechanical criteria of failure test procedures. Is applicable to inductive components (chokes and transformers) based on magnetically soft materials. Covers also discrete type components and the different types of surface-mountable inductive components (SMD).
Induktive Bauelemente - Zuverlässigkeitsmanagement
Composants inductifs - Gestion de la fiabilité
Etablit une large base de critères électriques et mécaniques de procédures d'essais de défaillance. Est applicable aux composants inductifs (inductances de lissage et transformateurs) utilisant des matériaux magnétiques doux. Couvre également les composants à connexions et les différents types de composants inductifs à montage en surface (CMS).
Inductive components - Reliability management (IEC 62211:2003)
General Information
Relations
Standards Content (Sample)
SLOVENSKI SIST EN 62211:2004
STANDARD
julij 2004
Inductive components - Reliability management (IEC 62211:2003)
ICS 29.100.10 Referenčna številka
SIST EN 62211:2004(en)
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD EN 62211
NORME EUROPÉENNE
EUROPÄISCHE NORM January 2004
ICS 29.100.10
English version
Inductive components –
Reliability management
(IEC 62211:2003)
Composants inductifs – Induktive Bauelemente -
Gestion de la fiabilité Zuverlässigkeitsmanagement
(CEI 62211:2003) (IEC 62211:2003)
This European Standard was approved by CENELEC on 2003-12-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland
and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2004 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 62211:2004 E
---------------------- Page: 2 ----------------------
EN 62211:2004 - 2 -
Foreword
The text of document 51/724/FDIS, future edition 1 of IEC 62211, prepared by IEC TC 51, Magnetic
components and ferrite materials, was submitted to the IEC-CENELEC parallel vote and was
approved by CENELEC as EN 62211 on 2003-12-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2004-09-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2006-12-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 62211:2003 was approved by CENELEC as a European
Standard without any modification.
__________
---------------------- Page: 3 ----------------------
- 3 - EN 62211:2004
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
1) 2)
IEC 60068-2-1 - Environmental testing EN 60068-2-1 1993
Part 2: Tests - Tests A: Cold
1) 2)
IEC 60068-2-2 - Part 2: Tests - Test B: Dry heat EN 60068-2-2 1993
1) 2)
IEC 60068-2-6 - Part 2: Tests - Test Fc: Vibration EN 60068-2-6 1995
(sinusoidal)
1) 2)
IEC 60068-2-14 - Part 2: Tests - Test N: Change of EN 60068-2-14 1999
temperature
1) 2)
IEC 60068-2-20 - Part 2: Tests - Test T: Soldering HD 323.2.20 S3 1988
1) 2)
IEC 60068-2-27 - Part 2: Tests - Test Ea and guidance: EN 60068-2-27 1993
Shock
1) 2)
IEC 60068-2-29 - Part 2: Tests - Test Eb and guidance: EN 60068-2-29 1993
Bump
1) 2)
IEC 60068-2-30 - Part 2: Tests - Test Db and guidance: EN 60068-2-30 1999
Damp heat, cyclic (12 + 12 hour cycle)
1) 2)
IEC 60068-2-58 - Part 2-58: Tests - Test Td: Test EN 60068-2-58 1999
methods for solderability, resistance to
dissolution of metallization and to
soldering heat of surface mounting
devices (SMD)
1) 2)
IEC 60068-2-78 - Part 2-78: Tests - Test Cab: Damp heat, EN 60068-2-78 2001
steady state
IEC 60424 Series Ferrite cores - Guide on the limits of EN 60424 Series
surface irregularities
1) 2)
IEC 61007 (mod) - Transformers and inductors for use in EN 61007 1997
electronic and telecommunication
equipment - Measuring methods and
test procedures
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.