EN 61394:2011
(Main)Overhead lines - Requirements for greases for aluminium, aluminium alloy and steel bare conductors
Overhead lines - Requirements for greases for aluminium, aluminium alloy and steel bare conductors
IEC 61394:2011 specifies the requirements and tests of greases designed for corrosion protection of bare overhead conductors.
Freileitungen - Anforderungen für Fette für blanke Leiter aus Aluminium, Aluminiumlegierung und Stahl
Lignes aériennes - Exigences pour les graisses pour conducteurs nus en aluminium, en alliage d'aluminium et en acier
Nadzemni vodi - Zahteve za masti za vodnike iz aluminija in aluminijevih zlitin ter gole jeklene vodnike (IEC 61394:2011)
Ta mednarodni standard določa zahteve in preskuse za masti za protikorozijsko zaščito golih nadzemnih vodnikov.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2012
Nadzemni vodi - Zahteve za masti za vodnike iz aluminija in aluminijevih zlitin ter
gole jeklene vodnike (IEC 61394:2011)
Overhead lines - Requirements for greases for aluminium, aluminium alloy and steel
bare conductors (IEC 61394:2011)
Freileitungen - Anforderungen für Fette für blanke Leiter aus Aluminium,
Aluminiumlegierung und Stahl (IEC 61394:2011)
Lignes a&riennes - Prescriptions pour les produits de protection pour conducteurs nus en
aluminium, en alliage d'aluminium ou en acier (CEI 61394:2011)
Ta slovenski standard je istoveten z: EN 61394:2011
ICS:
29.060.20 Kabli Cables
29.240.20 Daljnovodi Power transmission and
distribution lines
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 61394
NORME EUROPÉENNE
November 2011
EUROPÄISCHE NORM
ICS 29.060.20; 29.240.20
English version
Overhead lines -
Requirements for greases for aluminium, aluminium alloy and steel bare
conductors
(IEC 61394:2011)
Lignes aériennes - Freileitungen -
Exigences pour les graisses pour Anforderungen für Fette für blanke Leiter
conducteurs nus en aluminium, en alliage aus Aluminium, Aluminiumlegierung und
d'aluminium et en acier Stahl
(CEI 61394:2011) (IEC 61394:2011)
This European Standard was approved by CENELEC on 2011-11-16. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2011 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61394:2011 E
Foreword
The text of document 7/609/FDIS, future edition 1 of IEC 61394, prepared by IEC/TC 7 "Overhead
electrical conductors" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
(dop) 2012-08-16
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2014-11-16
• latest date by which the national
standards conflicting with the
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
Endorsement notice
The text of the International Standard IEC 61394:2011 was approved by CENELEC as a European
Standard without any modification.
- 3 - EN 61394:2011
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
IEC 60068-2-11 1981 Environmental testing - EN 60068-2-11 1999
+ corr. December 1999 Part 2: Tests - Test Ka: Salt mist
ISO 2137 2007 Petroleum products and lubricants - - -
Determination of cone penetration of
lubricating greases and petrolatum
ISO 2176 1995 Petroleum products - Lubricating grease - - -
Determination of dropping point
IEC 61394 ®
Edition 1.0 2011-10
INTERNATIONAL
STANDARD
colour
inside
Overhead lines – Requirements for greases for aluminium, aluminium alloy and
steel bare conductors
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
R
ICS 29.060.20; 29.240.20 ISBN 978-2-88912-706-1
– 2 – 61394 © IEC:2011(E)
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Designation system . 5
4 Requirements for grease . 6
5 Tests . 6
5.1 Classification of tests . 6
5.1.1 Type tests . 6
5.1.2 Sample tests . 6
5.2 Preconditioning of samples . 6
5.2.1 Type A products . 6
5.2.2 Type B products . 6
5.2.3 Products taken from a conductor . 6
5.3 Drop point . 7
5.4 High temperature stability (Type A products only) . 7
5.5 Penetrability test . 7
5.6 Low-temperature adherence . 7
5.7 Acidity/alkalinity (type B grease only) . 7
5.8 Ageing . 8
5.8.1 Preconditioning. 8
5.9 Corrosion tests . 8
5.10 Stability of grease on conductor at high temperature . 8
5.11 Stability of grease on conductor under short-circuit . 9
Annex A (normative) Acidity or alkalinity test method for type B grease . 11
Annex B (normative) Sample preparation and test procedure for ageing test. 13
Annex C (normative) Stability of grease on conductor at high temperature . 16
Annex D (normative) Stability of grease complete conductor under short-circuit . 17
Bibliography . 18
Figure 1 – Corrosion coupons . 10
Figure B.1 – Coupon for type A grease . 13
Figure B.2 – Coupon for type B grease . 14
Table 1 – Classification of tests . 6
Table A.1 – Acidity or alkalinity index formula . 12
61394 © IEC:2011(E) – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
OVERHEAD LINES –
REQUIREMENTS FOR GREASES FOR ALUMINIUM,
ALUMINIUM ALLOY AND STEEL BARE CONDUCTORS
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61394 has been prepared by IEC technical committee 7: Overhead
electrical conductors.
This first edition of IEC 61394 cancels and replaces the first edition of technical specification
IEC/TS 61394 published in 1997. It constitutes a technical revision and now has the status of
an International Standard.
The text of this standard is based on the following documents:
FDIS Report on voting
7/609/FDIS 7/613/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
– 4 – 61394 © IEC:2011(E)
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.
A bilingual version of this publication may be issued at a later date.
61394 © IEC:2011(E) – 5 –
OVERHEAD LINES –
REQUIREMENTS FOR GREASES FOR ALUMINIUM,
ALUMINIUM ALLOY AND STEEL BARE CONDUCTORS
1 Scope
This International Standard specifies the requirements and tests of greases designed for
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.