Mechanical structures for electrical and electronic equipment - Outdoor enclosures - Part 3: Environmental requirements, tests and safety aspects

IEC 61969-3:2020 is available as IEC 61969-3:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61969-3:2020 specifies a set of basic environmental requirements and tests, as well as safety aspects for outdoor enclosures under conditions of non-weather protected locations above ground. The purpose of this document is to define a minimum level of environmental performance in order to meet requirements of storage, transport and final installation. The intention is to establish basic environmental performance criteria for outdoor enclosure compliance. This third edition cancels and replaces the second edition published in 2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - alignment with the content of ETSI EN 300 019 and IEC 60721 series latest editions, particularly with the actualization of climate conditions; - new requirements added to reflect market requirements on environmental issues; - improvement on terminology and overall editorial improvement.

Mechanische Bauweisen für elektrische und elektronische Einrichtungen - Außengehäuse - Teil 3: Umgebungsanforderungen, Prüfungen und Sicherheitsaspekte

Structures mécaniques pour équipement électrique et électronique - Enveloppes de plein air - Partie 3: Exigences et essais d'environnement, et aspects liés à la sécurité

IEC 61969-3:2020 est disponible sous forme de IEC 61969-3:2020 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.L'IEC 61969-3: 2020 spécifie un ensemble d’exigences et d’essais d’environnement de base, ainsi que les aspects liés à la sécurité relatifs aux enveloppes de plein air placées dans les conditions suivantes: emplacement non protégé contre les intempéries, au-dessus du sol. L’objet du présent document est de définir un niveau minimal de performances environnementales, afin de répondre aux exigences de stockage, de transport et d’installation finale. Il s’agit d’établir des critères de performances environnementales de base en vue de la conformité des enveloppes de plein air. Cette troisième édition annule et remplace la deuxième édition parue en 2011. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: - alignement avec le contenu des dernières éditions des séries ETSI EN 300 019 et IEC 60721, en particulier concernant l’actualisation des conditions climatiques; - ajout de nouvelles exigences pour refléter celles du marché relatives aux questions environnementales; - amélioration de la terminologie et modifications éditoriales générales.

Mehanske strukture za električno in elektronsko opremo - Ohišja na prostem - 3. del: Okoljevarstvene zahteve, preskusi in varnostni vidiki (IEC 61969-3:2020)

General Information

Status
Published
Publication Date
30-Jul-2020
Current Stage
6060 - Document made available - Publishing
Start Date
31-Jul-2020
Completion Date
31-Jul-2020

Relations

Buy Standard

Standard
EN IEC 61969-3:2020
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 61969-3:2020
01-oktober-2020
Nadomešča:
SIST EN 61969-3:2012
Mehanske strukture za električno in elektronsko opremo - Ohišja na prostem - 3.
del: Okoljevarstvene zahteve, preskusi in varnostni vidiki (IEC 61969-3:2020)
Mechanical structures for electrical and electronic equipment - Outdoor enclosures - Part
3: Environmental requirements, tests and safety aspects (IEC 61969-3:2020)
Mechanische Bauweisen für elektronische Einrichtungen - Außengehäuse - Teil 3:
Umgebungsanforderungen, Prüfungen und Sicherheitsaspekte (IEC 61969-3:2020)
Structures mécaniques pour équipment électronique - Enveloppes de plein air - Partie 3:
Exigences environnementales, essais et aspects de la sécurité (IEC 61969-3:2020)
Ta slovenski standard je istoveten z: EN IEC 61969-3:2020
ICS:
31.240 Mehanske konstrukcije za Mechanical structures for
elektronsko opremo electronic equipment
SIST EN IEC 61969-3:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 61969-3:2020

---------------------- Page: 2 ----------------------
SIST EN IEC 61969-3:2020


EUROPEAN STANDARD EN IEC 61969-3

NORME EUROPÉENNE

EUROPÄISCHE NORM
July 2020
ICS 31.240 Supersedes EN 61969-3:2012 and all of its amendments
and corrigenda (if any)
English Version
Mechanical structures for electrical and electronic equipment -
Outdoor enclosures - Part 3: Environmental requirements, tests
and safety aspects
(IEC 61969-3:2020)
Structures mécaniques pour équipement électrique et Mechanische Bauweisen für elektronische Einrichtungen -
électronique - Enveloppes de plein air - Partie 3: Exigences Außengehäuse - Teil 3: Umgebungsanforderungen,
et essais d'environnement, et aspects liés à la sécurité Prüfungen und Sicherheitsaspekte
(IEC 61969-3:2020) (IEC 61969-3:2020)
This European Standard was approved by CENELEC on 2020-07-13. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 61969-3:2020 E

---------------------- Page: 3 ----------------------
SIST EN IEC 61969-3:2020
EN IEC 61969-3:2020 (E)
European foreword
The text of document 48D/721/FDIS, future edition 3 of IEC 61969-3, prepared by SC 48D
"Mechanical structures for electrical and electronic equipment" of IEC/TC 48 "Electrical connectors
and mechanical structures for electrical and electronic equipment" was submitted to the IEC-
CENELEC parallel vote and approved by CENELEC as EN IEC 61969-3:2020.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-04-13
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2023-07-13
document have to be withdrawn

This document supersedes EN 61969-3:2012 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 61969-3:2020 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60068-2-5 NOTE Harmonized as EN IEC 60068-2-5
IEC 60695-11-10 NOTE Harmonized as EN 60695-11-10
IEC 60721-3-2 NOTE Harmonized as EN IEC 60721-3-2
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.