IEC 61386-1:2008/AMD1:2017
(Amendment)Conduit systems for cable management - Part 1: General requirements
Conduit systems for cable management - Part 1: General requirements
Contains the definitions and explanation of terms that are used in parts 1 to 7 of this standard. Intended for use by technical committees in the preparation of standards in accordance with the principles contained in IEC Guide 104 and ISO/IEC Guide 51. IEC 61508 is also intended as a stand-alone standard.[
]Has the status of a basic safety publication in accordance with IEC Guide 104.[
]The contents of the corrigendum of April 1999 have been included in this copy.
Systèmes de conduits pour la gestion du câblage - Partie 1: Exigences générales
Contient les définitions et explications des termes utilisés dans les parties 1 à 7 de cette norme. Destinées à être utilisées par tous les comités d'études pour la mise au point de leurs normes, conformément aux principes décrits dans le Guide CEI 104 et dans le Guide ISO/CEI 51. La CEI 61508 est également prévue pour une utilisation en tant que norme autonome.[
]A le statut, d'une publication fondamentale de sécurité conformément au Guide 104.[
]Le contenu du corrigendum d'avril 1999 a été pris en considération dans cet exemplaire.
General Information
Relations
Standards Content (Sample)
IEC 61386-1 ®
Edition 2.0 2017-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
A MENDMENT 1
AM ENDEMENT 1
Conduit systems for cable management –
Part 1: General requirements
Systèmes de conduits pour la gestion du câblage –
Partie 1: Exigences générales
IEC 61386-1:2008-02/AMD1:2017-04(en-fr)
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de l'IEC ou du Comité national de l'IEC du pays du demandeur. Si vous avez des
questions sur le copyright de l'IEC ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez
les coordonnées ci-après ou contactez le Comité national de l'IEC de votre pays de résidence.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé Fax: +41 22 919 03 00
CH-1211 Geneva 20 info@iec.ch
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing 20 000 terms and definitions in
Technical Specifications, Technical Reports and other English and French, with equivalent terms in 16 additional
documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical
iPad. Vocabulary (IEV) online.
IEC publications search - www.iec.ch/searchpub IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a 65 000 electrotechnical terminology entries in English and
variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of
committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been
and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and
CISPR.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: csc@iec.ch.
A propos de l'IEC
La Commission Electrotechnique Internationale (IEC) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications IEC
Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possédez l’édition la
plus récente, un corrigendum ou amendement peut avoir été publié.
Catalogue IEC - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
Application autonome pour consulter tous les renseignements Le premier dictionnaire en ligne de termes électroniques et
bibliographiques sur les Normes internationales, électriques. Il contient 20 000 termes et définitions en anglais
Spécifications techniques, Rapports techniques et autres et en français, ainsi que les termes équivalents dans 16
documents de l'IEC. Disponible pour PC, Mac OS, tablettes langues additionnelles. Egalement appelé Vocabulaire
Android et iPad. Electrotechnique International (IEV) en ligne.
Recherche de publications IEC - www.iec.ch/searchpub Glossaire IEC - std.iec.ch/glossary
La recherche avancée permet de trouver des publications IEC 65 000 entrées terminologiques électrotechniques, en anglais
en utilisant différents critères (numéro de référence, texte, et en français, extraites des articles Termes et Définitions des
comité d’études,…). Elle donne aussi des informations sur les publications IEC parues depuis 2002. Plus certaines entrées
projets et les publications remplacées ou retirées. antérieures extraites des publications des CE 37, 77, 86 et
CISPR de l'IEC.
IEC Just Published - webstore.iec.ch/justpublished
Restez informé sur les nouvelles publications IEC. Just Service Clients - webstore.iec.ch/csc
Published détaille les nouvelles publications parues. Si vous désirez nous donner des commentaires sur cette
Disponible en ligne et aussi une fois par mois par email. publication ou si vous avez des questions contactez-nous:
csc@iec.ch.
IEC 61386-1 ®
Edition 2.0 2017-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
A MENDMENT 1
AM ENDEMENT 1
Conduit systems for cable management –
Part 1: General requirements
Systèmes de conduits pour la gestion du câblage –
Partie 1: Exigences générales
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.120.10 ISBN 978-2-8322-4162-2
– 2 – IEC 61386-1:2008/AMD1:2017
© IEC 2017
FOREWORD
This amendment has been prepared by subcommittee 23A: Cable management systems, of
IEC technical committee 23: Electrical accessories.
The text of this amendment is based on the following documents:
FDIS Report on voting
23A/831/FDIS 23A/838/RVD
Full information on the voting for the approval of this amendment can be found in the report
on voting indicated in the above table.
The committee has decided that the contents of this amendment and the base publication will
remain unchanged until the stability date indicated on the IEC website under
"http://webstore.iec.ch" in the data related to the specific publication. At this date, the
publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
_____________
2 Normative references
Replace the existing references to IEC 60529 and IEC 60695-2-11 by the following new
references:
IEC 60529:1989 + AMD1:1999+AMD2:2013, Degrees of protection provided by enclosures (IP
Code)
IEC 60695-2-11:2014, Fire hazard testing – Part 2-11: Glowing/hot-wire based test methods –
Glow-wire flammability test method for end-products (GWEPT)
Add the following new references:
IEC 61386-21:2002, Conduit systems for cable management – Part 21: Particular
requirements – Rigid conduit systems
IEC 61386-22:2002, Conduit Systems for cable management – Part 22: Particular
requirements – Pliable conduit systems
IEC 61386-23:2002, Conduit systems for cable management – Part 23: Particular
requirements – Flexible conduit systems
IEC 61386-24:2004, Conduit systems for cable management – Part 24: Particular
requirements – Conduit systems buried underground
IEC 61386-25:2011, Conduit systems for cable management – Part 25: Particular
requirements – Conduit fixing devices
© IEC 2017
3.14
Replace existing definition 3.14 with the following new definition:
self-recovering conduit
pliable conduit which deforms when a transverse force is applied for a short time and which,
after removal of this force, returns close to its original shape after a defined period
5.9
Delete this subclause.
7.1.1
Replace the existing text of Subclause 7.1.1 with the following new text:
The conduit or smallest supplied package shall also be marked with the classification code, in
accordance with Annex A, and shall include at least the first four digits.
Add, after Subclause 7.1.1, the following new subclause:
7.1.1.1
Self-recovering conduits shall also be marked on the conduit or smallest supplied package
with the classification code, in accordance with Annex A, and shall include at least the first
five digits.
Compliance is checked by inspection.
7.3
Add, after the first paragraph, the following new paragraph:
Flame propagating conduits shall also be marked with the following symbol:
– along its entire length at intervals of preferably 1 m but not longer than 3 m with each
length being marked at least once, and
– when the packaging of the smallest supplied package prevents the marking on the conduit
being seen, the symbol shall be marked on the packaging or by means of a label
IEC 60417-6180:2013-01
7.6
Replace the existing text of Subclause 7.6 with the following new text:
The marking shall be durable and clearly legible.
– 4 – IEC 61386-1:2008/AMD1:2017
© IEC 2017
Compliance is checked by inspection, using normal or corrected vision, without additional
magnification and by rubbing the marking for 15 s with a piece of cotton cloth soaked with
water and again for 15 s with a piece of cotton cloth soaked with n-hexane 95 % .
When using the liquid specified for the test, precautions as stated in the relative material
safety datasheet provided by the chemical supplier shall be taken to safeguard the laboratory
technicians.
Laser marking directly on the product and marking made by moulding, pressing or engraving
are not subjected to this test.
The marking surface to be tested shall be dried before rubbing the marking with n-hexane
95 % solvent.
Rubbing shall commence immediately after soaking the piece of cotton, applying a
compression force of (5 ± 1) N at a rate of about one cycle per second (a cycle comprising a
forward and backward movement along the length of the marking). For markings longer than
20 mm, rubbing can be limited to a part of the marking, over a path of at least 20 mm length.
The compression force is applied by means of a test piston which is wrapped with cotton
comprising of cotton wool covered by a piece of cotton medical gauze.
The test piston shall have the dimensions given in Figure 9 and shall be made of an elastic
material which is inert against the test liquids and has a Shore-A hardness of 47 ± 5 (for
example synthetic rubber).
When it is not possible to carry out the test on the specimens due to the shape/size of the
product, a suitable piece having the same characteristics as the product can be submitted to
the test.
After the test, the marking shall be legible.
10.3.1
Replace the existing second paragraph of Subclause 10.3.1 with the following new text:
Conduits are tested without fittings. Fittings are tested with a short length of conduit
assembled to them as in normal use.
Delete the note.
10.3.2
Replace the existing text of Subclause 10.3.2 with the following new text:
The test apparatus is placed on a firm flat surface.
The samples are conditioned for 2 h in a cold chamber at the temperature specified in Table 1
with a tolerance of ± 2 °C corresponding to the declared classification. The samples are
removed from the cold chamber and placed on a flat steel surface as shown in Figure 2.
The hammer shall fall once on each sample. The time between the removal of the sample
from the cold chamber and the completion of the impact test shall not be greater than 10 s.
The mass of the hammer and the fall height are specified in Table 5.
____________
Chemical Abstracts Service Registry Number, CAS RN, 110-54-3.
© IEC 2017
The test is made on what is likely to be the weakest part of the conduit or fitting except that it
is not applied within 5 mm of any conduit entry of the fitting. Conduit test samples shall be
tested at the centre of their length.
11.3.1.2
Replace the existing first paragraph of Subclause 11.3.1.2 with the following new text:
After 24 h ± 15 min, an a.c. voltage of substantially sine wave form and having a frequency
between 45 Hz and 65 Hz is applied across the two electrodes. The voltage is then gradually
increased from 1 000 V to 2 000 V a.c. Once the maximum voltage has been reached it shall
+5
be maintained for a period of 60 s.
Replace the last paragraph with the following new text:
The samples shall be considered to have adequate electrical insulating strength if a 100 mA
trip device, incorporated into the circuit, does not trip during the test.
13.1.3 Spread of fire
Add, at the end of Subclause 13.1.3, the following new Note:
NOTE In accordance with 422.3.4 of IEC 60364-4-42:2010 and Annex F of IEC 60364-5-52:2009, flame
propagating conduits are not suitable for use in buildings, unless embedded in non-combustible material, such as
concrete.
14.2.2.2
Replace the existing first paragraph of Subclause 14.2.2.2 with the following new paragraph:
Medium protection conduit and conduit fittings shall be cleaned with a piece of wadding
soaked in white spirit.
Figure 3 – Assembly of conduit and conduit fitting for bonding test
Replace the existing title of Figure 3 with the following new title:
Figure 3 – Example of the assembly of conduit and conduit fittings for bonding test
– 6 – IEC 61386-1:2008/AMD1:2017
© IEC 2017
Add, after Figure 8, the following new figure:
C
B
IEC
Dimensions
mm
A B C
20 20 2
Key
A Diameter of piston
B Head radius
Figure 9 – Test piston and dimensions for rubbing test of marking
Annex
Add, after Annex B, the following new Annex C
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.