IEC 62899-301-3:2024
(Main)Printed Electronics - Part 301-3: Equipment - Contact printing - Rigid master - Method to measure the shape errors of printing plate rollers
Printed Electronics - Part 301-3: Equipment - Contact printing - Rigid master - Method to measure the shape errors of printing plate rollers
IEC 62899-301-3:2024 defines measurement terms and methods related to the shape errors of printing plate rollers. Measurement terms include radius, total run-out, and three kinds of shape errors of printing plate rollers that are axial deviation, radial deviation, and cross-sectional deviation. The remaining shape error excluding the three errors mentioned above is defined as a residual shape error.
This document applies to printing plate rollers with or without patterns while excluding the pattern area for the measurement.
General Information
Standards Content (Sample)
IEC 62899-301-3 ®
Edition 1.0 2024-09
INTERNATIONAL
STANDARD
Printed Electronics –
Part 301-3: Equipment – Contact printing – Rigid master – Method to measure
the shape errors of printing plate rollers
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
IEC Secretariat Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.
IEC publications search - webstore.iec.ch/advsearchform IEC Products & Services Portal - products.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews, graphical symbols and the glossary.
committee, …). It also gives information on projects, replaced With a subscription you will always have access to up to date
and withdrawn publications. content tailored to your needs.
IEC Just Published - webstore.iec.ch/justpublished
Electropedia - www.electropedia.org
Stay up to date on all new IEC publications. Just Published
The world's leading online dictionary on electrotechnology,
details all new publications released. Available online and once
containing more than 22 500 terminological entries in English
a month by email.
and French, with equivalent terms in 25 additional languages.
Also known as the International Electrotechnical Vocabulary
IEC Customer Service Centre - webstore.iec.ch/csc
(IEV) online.
If you wish to give us your feedback on this publication or need
further assistance, please contact the Customer Service
Centre: sales@iec.ch.
IEC 62899-301-3 ®
Edition 1.0 2024-09
INTERNATIONAL
STANDARD
Printed Electronics –
Part 301-3: Equipment – Contact printing – Rigid master – Method to measure
the shape errors of printing plate rollers
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 19.080; 37.100.01 ISBN 978-2-8322-9717-9
– 2 – IEC 62899-301-3:2024 © IEC 2024
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 7
4 Measurement methods . 10
4.1 General . 10
4.2 Measuring instrument. 10
4.3 Measuring process . 10
4.4 Report. 12
Annex A (informative) Printing force variation of the printing plate roller . 13
Annex B (normative) Numerical procedures to extract the shape errors of the printing
plate rollers . 14
B.1 Extraction of the least square reference circle for each measured
circumference of the printing cylinder . 14
B.2 Remove the axial deviations and the radial deviations . 15
B.3 Calculate the cross-section deviations . 16
B.4 Calculate the residual shape errors . 16
Annex C (informative) Examples of report . 17
C.1 Example of report . 17
C.2 Example of report 2 . 20
Bibliography . 24
Figure 1 – General shape of printing plate roller . 8
Figure 2 – Datum axis of the printing plate roller for measuring shape errors of the
printing cylinder . 8
Figure 3 – Median line deviation of a cylinder . 9
Figure 4 – Radius deviation of a cylinder . 9
Figure 5 – Cross-sectional deviation of a cylinder . 10
Figure A.1 – Printing force variations in two different cases . 13
Figure A.2 – Axial deviation with a slope relative to the datum axis . 13
Figure A.3 – Axial deviation with an offset relative to the datum axis . 13
Figure B.1 – Measurement of the printing cylinder . 14
Figure B.2 – Least square reference circle of the i-th circumferential measurement . 15
Figure C.1 – Measurement setup . 17
Figure C.2 – Measurement of the datum axis . 18
Figure C.3 – Measurement of the circumferences of the printing cylinder with the label
meaning the z-axis position of each measured circumference . 18
Figure C.4 – Graphical report of Table C.1 . 19
Figure C.5 – Extracted cross-section variation . 19
Figure C.6 – Residual shape errors . 20
Figure C.7 – Measurement setup . 21
Figure C.8 – Measurement of the datum axis . 21
Figure C.9 – Measurement of the circumferences of the printing cylinder with the label
meaning the z-axis position of each measured circumference . 22
Figure C.10 – Graphical report of Table C.2 . 22
Figure C.11 – Extracted cross-section variation . 23
Figure C.12 – Residual shape errors . 23
Table 1 – Guideline for the sample points on each circumferential measurement . 11
Table B.1 – Report form for the axial deviations and radial deviations of the printing
cylinder . 15
Table C.1 – Report for the axial deviations and radial deviations of the printing cylinder
fitted from measured circumferences given in Figure C.3 . 19
Table C.2 – Report for the axial deviations and radial deviations of the printing cylinder
fitted from measured circumferences given in Figure C.9 . 22
– 4 – IEC 62899-301-3:2024 © IEC 2024
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
PRINTED ELECTRONICS –
Part 301-3: Equipment – Contact printing – Rigid master –
Method to measure the shape errors of printing plate rollers
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in
respect thereof. As of the date of publication of this document, IEC had not received notice of (a) patent(s), which
may be required to implement this document. However, implementers are cautioned that this may not represent
the latest information, which may be obtained from the patent database available at https://patents.iec.ch. IEC
shall not be held responsible for identifying any or all such patent rights.
IEC 62899-302-3 has been prepared by IEC technical committee 119: Printed Electronics. It is
an International Standard.
The text of this International Standard is based on the following documents:
Draft Report on voting
119/505/FDIS 119/511/RVD
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/publications.
A list of all parts in the IEC 62899 series, published under the general title Printed electronics,
can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.