Home and Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS) - Part 5-3: EMC requirements for HBES/BACS used in industrial environments

IEC 63044-5-3:2017 is a product family standard that sets the minimum level of EMC performance for the HBES/BACS network in addition to the product EMC standards for HBES/BACS devices. It also applies to devices used within an HBES/BACS network for which no specific HBES/BACS product EMC standard exists. In addition, it defines EMC requirements for the interface of equipment intended to be connected to an HBES/BACS network. It does not apply to interfaces to other networks.
NOTE An example of other networks is a dedicated ICT network covered by CISPR 22 and 23.
This document specifies EMC requirements for HBES/BACS to be installed in industrial environments, according to the definition given in IEC 61000-6-2.
NOTE Industrial environment covers the office spaces that may be present in industrial premises. Industrial automation systems are outside the scope. This document is applicable (but not limited) to
operator stations and other human–system interface devices,
devices for management functions,
control devices, automation stations and application-specific controllers,
field devices and their interfaces,
cabling and interconnection of devices,  used within a dedicated HBES/BACS network. This publication is to be read in conjunction with IEC 63044-5-1:2017.

Systemes électroniques pour les foyers domestiques et les bâtiments (HBES) et systèmes de gestion technique du bâtiment (SGTB) - Partie 5-3: Exigences CEM relatives aux HBES/SGTB destinés à être utilisés en environnement industriel

L'IEC 63044-5-3:2017 est une norme de famille de produits qui établit le niveau minimal de performance CEM pour le réseau HBES/SGTB outre les normes CEM de produits applicables aux dispositifs HBES/SGTB. Elle s'applique également aux dispositifs utilisés dans un réseau HBES/SGTB pour lequel il n'existe aucune norme CEM de produit HBES/SGTB spécifique. De plus, elle spécifie des exigences CEM relatives à l'interface des équipements destinés à être connectés à un réseau HBES/SGTB. Elle ne s'applique pas aux interfaces avec d'autres réseaux.
NOTE Un réseau TIC dédié traité par le CISPR 22 et 23 constitue un exemple d'autres réseaux.
Le présent document spécifie des exigences CEM relatives aux systèmes HBES/SGTB à installer dans un environnement industriel selon la définition de l'IEC 61000-6-2.
NOTE L'expression "environnement industriel" couvre les locaux pour bureaux qui peuvent être présents dans des bâtiments industriels. Les systèmes d'automatisation industrielle ne relèvent pas du domaine d'application du présent document. Le présent document est applicable (sans toutefois s'y limiter) aux
postes d’opérateur et autres dispositifs d’interface homme–système,
dispositifs pour des fonctions de gestion,
dispositifs de commande, postes d’automatisation et contrôleurs spécifiques à une application,
dispositifs de terrain et leurs interfaces,
câblage et à l’interconnexion des dispositifs,  utilisés dans un réseau HBES/SGTB dédié. Cette publication doit être lue conjointement avec l’IEC 63044-5-1:2017.

General Information

Status
Published
Publication Date
26-Jan-2017
Technical Committee
Current Stage
PPUB - Publication issued
Completion Date
27-Jan-2017
Ref Project

Buy Standard

Standard
IEC 63044-5-3:2017 - Home and Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS) - Part 5-3: EMC requirements for HBES/BACS used in industrial environments
English and French language
16 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (sample)

IEC 63044-5-3
Edition 1.0 2017-01
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Home and building electronic systems (HBES) and building automation and
control systems (BACS) –
Part 5-3: EMC requirements for HBES/BACS used in industrial environments
Systèmes électroniques pour les foyers domestiques et les bâtiments (HBES) et
systèmes de gestion technique du bâtiment (SGTB) –
Partie 5-3: Exigences CEM relatives aux HBES/SGTB destinés à être utilisés en
environnement industriel
IEC 63044-5-3:2017-01(en-fr)
---------------------- Page: 1 ----------------------
THIS PUBLICATION IS COPYRIGHT PROTECTED
Copyright © 2017 IEC, Geneva, Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form

or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from

either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC

copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or

your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite

ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie

et les microfilms, sans l'accord écrit de l'IEC ou du Comité national de l'IEC du pays du demandeur. Si vous avez des

questions sur le copyright de l'IEC ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez

les coordonnées ci-après ou contactez le Comité national de l'IEC de votre pays de résidence.

IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé Fax: +41 22 919 03 00
CH-1211 Geneva 20 info@iec.ch
Switzerland www.iec.ch
About the IEC

The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes

International Standards for all electrical, electronic and related technologies.
About IEC publications

The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the

latest edition, a corrigenda or an amendment might have been published.
IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org

The stand-alone application for consulting the entire The world's leading online dictionary of electronic and

bibliographical information on IEC International Standards, electrical terms containing 20 000 terms and definitions in

Technical Specifications, Technical Reports and other English and French, with equivalent terms in 16 additional

documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical

iPad. Vocabulary (IEV) online.

IEC publications search - www.iec.ch/searchpub IEC Glossary - std.iec.ch/glossary

The advanced search enables to find IEC publications by a 65 000 electrotechnical terminology entries in English and

variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of

committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been

and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and

CISPR.
IEC Just Published - webstore.iec.ch/justpublished

Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc

details all new publications released. Available online and If you wish to give us your feedback on this publication or

also once a month by email. need further assistance, please contact the Customer Service

Centre: csc@iec.ch.
A propos de l'IEC

La Commission Electrotechnique Internationale (IEC) est la première organisation mondiale qui élabore et publie des

Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications IEC

Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possédez l’édition la

plus récente, un corrigendum ou amendement peut avoir été publié.
Catalogue IEC - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
Application autonome pour consulter tous les renseignements
Le premier dictionnaire en ligne de termes électroniques et
bibliographiques sur les Normes internationales,
électriques. Il contient 20 000 termes et définitions en anglais
Spécifications techniques, Rapports techniques et autres
et en français, ainsi que les termes équivalents dans 16
documents de l'IEC. Disponible pour PC, Mac OS, tablettes
langues additionnelles. Egalement appelé Vocabulaire
Android et iPad.
Electrotechnique International (IEV) en ligne.
Recherche de publications IEC - www.iec.ch/searchpub
Glossaire IEC - std.iec.ch/glossary
65 000 entrées terminologiques électrotechniques, en anglais
La recherche avancée permet de trouver des publications IEC

en utilisant différents critères (numéro de référence, texte, et en français, extraites des articles Termes et Définitions des

comité d’études,…). Elle donne aussi des informations sur les publications IEC parues depuis 2002. Plus certaines entrées

projets et les publications remplacées ou retirées. antérieures extraites des publications des CE 37, 77, 86 et

CISPR de l'IEC.
IEC Just Published - webstore.iec.ch/justpublished
Service Clients - webstore.iec.ch/csc
Restez informé sur les nouvelles publications IEC. Just

Published détaille les nouvelles publications parues. Si vous désirez nous donner des commentaires sur cette

Disponible en ligne et aussi une fois par mois par email. publication ou si vous avez des questions contactez-nous:

csc@iec.ch.
---------------------- Page: 2 ----------------------
IEC 63044-5-3
Edition 1.0 2017-01
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Home and building electronic systems (HBES) and building automation and
control systems (BACS) –
Part 5-3: EMC requirements for HBES/BACS used in industrial environments
Systèmes électroniques pour les foyers domestiques et les bâtiments (HBES) et
systèmes de gestion technique du bâtiment (SGTB) –
Partie 5-3: Exigences CEM relatives aux HBES/SGTB destinés à être utilisés en
environnement industriel
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.120.01; 29.120.99 ISBN 978-2-8322-3776-2

Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 3 ----------------------
– 2 – IEC 63044-5-3:2017 © IEC 2017
CONTENTS

FOREWORD ........................................................................................................................... 3

INTRODUCTION ..................................................................................................................... 5

1 Scope .............................................................................................................................. 6

2 Normative references ...................................................................................................... 6

3 Terms, definitions and abbreviated terms ........................................................................ 6

4 General requirements ...................................................................................................... 7

5 Performance criteria ........................................................................................................ 7

6 Standard test conditions .................................................................................................. 7

7 EMC requirements ........................................................................................................... 7

7.1 Immunity requirements ............................................................................................ 7

7.2 Emission requirements ............................................................................................ 8

Table 1 – EMC immunity requirements for HBES/BACS network ports .................................... 8

---------------------- Page: 4 ----------------------
IEC 63044-5-3:2017 © IEC 2017 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
HOME AND BUILDING ELECTRONIC SYSTEMS (HBES) AND
BUILDING AUTOMATION AND CONTROL SYSTEMS (BACS) –
Part 5-3: EMC requirements for HBES/BACS
used in industrial environments
FOREWORD

1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising

all national electrotechnical committees (IEC National Committees). The object of IEC is to promote

international co-operation on all questions concerning standardization in the electrical and electronic fields. To

this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,

Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC

Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested

in the subject dealt with may participate in this preparatory work. International, governmental and non-

governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely

with the International Organization for Standardization (ISO) in accordance with conditions determined by

agreement between the two organizations.

2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international

consensus of opinion on the relevant subjects since each technical committee has representation from all

interested IEC National Committees.

3) IEC Publications have the form of recommendations for international use and are accepted by IEC National

Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC

Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any

misinterpretation by any end user.

4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications

transparently to the maximum extent possible in their national and regional publications. Any divergence

between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in

the latter.

5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity

assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any

services carried out by independent certification bodies.

6) All users should ensure that they have the latest edition of this publication.

7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and

members of its technical committees and IEC National Committees for any personal injury, property damage or

other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and

expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC

Publications.

8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is

indispensable for the correct application of this publication.

9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of

patent rights. IEC shall not be held responsible for identifying any or all such patent rights.

International Standard IEC 63044-5-3 has been prepared by IEC technical committee 23:

Electrical accessories.
The text of this standard is based on the following documents:
CDV Report on voting
23/738/CDV 23/750/RVC

Full information on the voting for the approval of this standard can be found in the report on

voting indicated in the above table.

This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

---------------------- Page: 5 ----------------------
– 4 – IEC 63044-5-3:2017 © IEC 2017

This International Standard is to be used in conjunction with IEC 63044-5-1:2017.

A list of all parts in the IEC 63044 series, published under the general title Home and Building

Electronic Systems (HBES) and Building Automation and Control Systems (BACS), can be

found on the IEC website.

The committee has decided that the contents of this publication will remain unchanged until

the stability date indicated on the IEC website under "http://webstore.iec.ch" in the data

related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
---------------------- Page: 6 ----------------------
IEC 63044-5-3:2017 © IEC 2017 – 5 –
INTRODUCTION

The IEC 63044 series deals with developing and testing Home and Building Electronic

Systems (HBES) and Building Automation and Control Systems (BACS).
The IEC 63044-5 series ensures a common level of EMC requirements for HBES/BACS
devices.
---------------------- Page: 7 ----------------------
– 6 – IEC 63044-5-3:2017 © IEC 2017
HOME AND BUILDING ELECTRONIC SYSTEMS (HBES) AND
BUILDING AUTOMATION AND CONTROL SYSTEMS (BACS) –
Part 5-3: EMC requirements for HBES/BACS
used in industrial environments
1 Scope
Clause 1 of IEC 63044-5-1:2017 applies, with the following modification:
Replace the fourth paragraph with the following:

This document specifies EMC requirements for HBES/BACS to be installed in industrial

environments, according to the definition given in IEC 61000-6-2.

NOTE Industrial environment covers the office spaces that may be present in industrial premises.

Industrial automation systems are outside the scope.
2 Normative references

The following documents are referred to in the text in such a way that some or all of their

content constitutes requirements of this document. For dated references, only the edition

cited applies. For undated references, the latest edition of the referenced document (including

any amendments) applies.

IEC 63044-5-1, Home and Building Electronic Systems (HBES) and Building Automation and

Control Systems (BACS) – Part 5-1: EMC requirements, conditions and test set-up

IEC 61000-4-4, Electromagnetic compatibility (EMC) – Part 4-4: Testing and measurement

techniques – Electrical fast transient/burst immunity test

IEC 61000-4-5, Electromagnetic compatibility (EMC) – Part 4-5: Testing and measurement

techniques – Surge immunity test

IEC 61000-4-6, Electromagnetic compatibility (EMC) – Part 4-6: Testing and measurement

techniques – Immunity to conducted disturbances, induced by radio-frequency fields

IEC 61000-6-2, Electromagnetic compatibility (EMC) – Part 6-2: Generic standards –

Immunity standard for industrial environments
IEC 61000-6-4, Electromagnetic compatibility (EMC) – Part 6-4: Generic st
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.