Gas cylinders — Inspection and maintenance of valves

This document specifies requirements for the inspection and maintenance of valves [including ball valves and valves with integrated pressure regulator (VIPRs)] for: a) refillable transportable gas cylinders; b) cylinder bundles; c) pressure drums and tubes; which convey compressed, liquefied or dissolved gases. This document does not apply to valves for liquefied petroleum gas (LPG). NOTE Where there is no risk of ambiguity, gas cylinders, cylinder bundles, pressure drums and tubes are addressed with the collective term “gas cylinders” within this document. This document is applicable to valves reused at the time of the periodic inspection of gas cylinders, cylinder bundles, pressure drums and tubes, and can be applied at any other time, e.g. at a change of gas service (see ISO 11621). This document does not apply to the routine inspection of valves, e.g. carried out at the time of a gas cylinder filling.

Bouteilles à gaz — Contrôle et maintenance des robinets

Le présent document spécifie les exigences de contrôle et de maintenance des robinets [y compris les robinets à boisseau sphérique et les robinets avec détendeur de pression intégré (VIPR)] pour: a) les bouteilles à gaz transportables et rechargeables; b) les cadres de bouteilles; c) les fûts à pression et tubes; qui acheminent des gaz comprimés, liquéfiés ou dissous. Le présent document ne s’applique pas aux robinets pour GPL (gaz de pétrole liquéfié). NOTE Lorsqu’il n’y a pas de risque d’ambigüité, les bouteilles à gaz, cadres de bouteilles et tubes et fûts à pression sont désignés par le terme générique «bouteilles à gaz» dans le présent document. Le présent document est applicable aux robinets réutilisés lors du contrôle périodique des bouteilles à gaz, cadres de bouteilles, fûts à pression et tubes, et à n’importe quel autre moment; par exemple lors du changement de service de gaz (voir l’ISO 11621). Le présent document n’est pas applicable aux contrôles de routine des robinets, par exemple effectués au moment du remplissage des bouteilles à gaz.

General Information

Status
Published
Publication Date
21-Mar-2022
Current Stage
6060 - International Standard published
Start Date
22-Mar-2022
Due Date
09-Oct-2023
Completion Date
22-Mar-2022
Ref Project

Relations

Buy Standard

Standard
ISO 22434:2022 - Gas cylinders — Inspection and maintenance of valves Released:3/22/2022
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 22434:2022 - Gas cylinders — Inspection and maintenance of valves Released:3/22/2022
French language
8 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
ISO/FDIS 22434 - Gas cylinders -- Inspection and maintenance of valves
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 22434
Second edition
2022-03
Gas cylinders — Inspection and
maintenance of valves
Bouteilles à gaz — Contrôle et maintenance des robinets
Reference number
ISO 22434:2022(E)
© ISO 2022

---------------------- Page: 1 ----------------------
ISO 22434:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
  © ISO 2022 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 22434:2022(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General requirements . 2
4.1 Frequency of inspection and maintenance . 2
4.2 Personnel . 2
4.3 Safety concerns . 2
5 Inspection and maintenance . 3
5.1 General . 3
5.2 Inspection . 3
5.2.1 General . 3
5.2.2 Cleaning . 3
5.2.3 External examination — Valve remaining in the gas cylinder . 3
5.2.4 Additional external examination — Valve removed from gas cylinder . 4
5.2.5 Acceptance criteria . 4
5.3 Maintenance . 4
5.3.1 Minor repairs . 4
5.3.2 Major repairs . 4
5.3.3 Refurbishment . 5
5.4 Testing . 6
6 Marking . . 6
7 Packaging. 6
8 Scrapping . 6
Bibliography . 7
iii
© ISO 2022 – All rights reserved

---------------------- Page: 3 ----------------------
ISO 22434:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 58, Gas cylinders, Subcommittee SC 2,
Cylinder fittings, in collaboration with the European Committee for Standardization (CEN) Technical
Committee CEN/TC 23, Transportable gas cylinders, in accordance with the Agreement on technical
cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 22434:2006), which has been technically
revised. The main changes are as follows:
— the Scope has been revised;
— the Normative references have been updated;
— the Terms and definitions have been updated;
— subclauses 5.1, 5.2.2 and 5.3.2 have been modified;
— Clause 6 “Testing” has been moved to 5.4 and has been modified;
— marking requirements have been modified;
— the Bibliography has been updated.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
  © ISO 2022 – All rights reserved

---------------------- Page: 4 ----------------------
ISO 22434:2022(E)
Introduction
[1]
This document has been written so that it is suitable to be referenced in the UN Model Regulations .
v
© ISO 2022 – All rights reserved

---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 22434:2022(E)
Gas cylinders — Inspection and maintenance of valves
1 Scope
This document specifies requirements for the inspection and maintenance of valves [including ball
valves and valves with integrated pressure regulator (VIPRs)] for:
a) refillable transportable gas cylinders;
b) cylinder bundles;
c) pressure drums and tubes;
which convey compressed, liquefied or dissolved gases.
This document does not apply to valves for liquefied petroleum gas (LPG).
NOTE Where there is no risk of ambiguity, gas cylinders, cylinder bundles, pressure drums and tubes are
addressed with the collective term “gas cylinders” within this document.
This document is applicable to valves reused at the time of the periodic inspection of gas cylinders,
cylinder bundles, pressure drums and tubes, and can be applied at any other time, e.g. at a change of gas
service (see ISO 11621).
This document does not apply to the routine inspection of valves, e.g. carried out at the time of a gas
cylinder filling.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 10286, Gas cylinders — Vocabulary
ISO 14246, Gas cylinders — Cylinder valves — Manufacturing tests and examinations
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 10286 and the following apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
3.1
inspection
procedure to determine if a valve is suitable for further service
3.2
dismantling
separation of the valve into its component parts, such that the main pressure barrier of the valve is
breached
1
© ISO 2022 – All rights reserved

---------------------- Page: 6 ----------------------
ISO 22434:2022(E)
3.3
removal
disconnection of the valve from the gas cylinder
3.4
maintenance
operations required to keep the valve in working condition
Note 1 to entry: This covers minor repairs (3.4.1), major repairs (3.4.2) and refurbishment (3.4.3).
3.4.1
minor repair
operation including cleaning and replacement of non-pressure-retaining components
EXAMPLE Handwheel, outlet flow restrictor.
3.4.2
major repair
operation including replacement of valve accessories which are incorporated within the pressure
boundary, but do not require dismantling (3.2) of the valve
EXAMPLE Pressure relief device (PRD), pressure g
...

NORME ISO
INTERNATIONALE 22434
Deuxième édition
2022-03
Bouteilles à gaz — Contrôle et
maintenance des robinets
Gas cylinders — Inspection and maintenance of valves
Numéro de référence
ISO 22434:2022(F)
© ISO 2022

---------------------- Page: 1 ----------------------
ISO 22434:2022(F)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2022
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii
  © ISO 2022 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 22434:2022(F)
Sommaire Page
Avant-propos .iv
Introduction .v
1 Domaine d’application . 1
2 Références normatives .1
3 Termes et définitions . 1
4 Exigences générales . .2
4.1 Fréquence du contrôle et de la maintenance . 2
4.2 Personnel . 2
4.3 Sécurité . 2
5 Contrôle et maintenance .3
5.1 Généralités . 3
5.2 Contrôle . . 3
5.2.1 Généralités . 3
5.2.2 Nettoyage . 3
5.2.3 Examen externe — Robinet restant en place sur la bouteille à gaz . 3
5.2.4 Examen externe complémentaire — Robinet déposé . 4
5.2.5 Critères d’acceptation . 4
5.3 Maintenance . 5
5.3.1 Réparations mineures . 5
5.3.2 Réparations majeures . 5
5.3.3 Remise en état . 5
5.4 Essais . 6
6 Marquage . 6
7 Emballage . 6
8 Mise au rebut . 7
Bibliographie . 8
iii
© ISO 2022 – Tous droits réservés

---------------------- Page: 3 ----------------------
ISO 22434:2022(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a
été rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir
www.iso.org/directives).
L'attention est attirée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de
brevets reçues par l'ISO (voir www.iso.org/brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion
de l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles
techniques au commerce (OTC), voir www.iso.org/avant-propos.
Le présent document a été élaboré par le comité technique ISO/TC 58, Bouteilles à gaz, sous-comité SC 2,
Accessoires de bouteilles, en collaboration avec le comité technique CEN/TC 23, Bouteilles à gaz
transportables, du Comité européen de normalisation (CEN) conformément à l’Accord de coopération
technique entre l’ISO et le CEN (Accord de Vienne).
Cette deuxième édition annule et remplace la première édition (ISO 22434:2006), qui a fait l’objet d’une
révision technique. Les principales modifications sont les suivantes:
— le Domaine d’application a été révisé;
— les Références normatives ont été mises à jour;
— les Termes et les définitions ont été mis à jour;
— les paragraphes 5.1, 5.2.2 et 5.3.2 ont été modifiés;
— l’Article 6 «Essais» a été déplacé à 5.4 et a été modifié;
— les prescriptions de marquage ont été modifiées;
— la Bibliographie a été mise à jour.
Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent
document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes
se trouve à l’adresse www.iso.org/fr/members.html.
iv
  © ISO 2022 – Tous droits réservés

---------------------- Page: 4 ----------------------
ISO 22434:2022(F)
Introduction
Le présent document a été élaboré afin qu’il soit susceptible d’être référencé dans le Règlement type des
[1]
Nations Unies .
v
© ISO 2022 – Tous droits réservés

---------------------- Page: 5 ----------------------
NORME INTERNATIONALE ISO 22434:2022(F)
Bouteilles à gaz — Contrôle et maintenance des robinets
1 Domaine d’application
Le présent document spécifie les exigences de contrôle et de maintenance des robinets [y compris les
robinets à boisseau sphérique et les robinets avec détendeur de pression intégré (VIPR)] pour:
a) les bouteilles à gaz transportables et rechargeables;
b) les cadres de bouteilles;
c) les fûts à pression et tubes;
qui acheminent des gaz comprimés, liquéfiés ou dissous.
Le présent document ne s’applique pas aux robinets pour GPL (gaz de pétrole liquéfié).
NOTE Lorsqu’il n’y a pas de risque d’ambigüité, les bouteilles à gaz, cadres de bouteilles et tubes et fûts à
pression sont désignés par le terme générique «bouteilles à gaz» dans le présent document.
Le présent document est applicable aux robinets réutilisés lors du contrôle périodique des bouteilles à
gaz, cadres de bouteilles, fûts à pression et tubes, et à n’importe quel autre moment; par exemple lors du
changement de service de gaz (voir l’ISO 11621).
Le présent document n’est pas applicable aux contrôles de routine des robinets, par exemple effectués
au moment du remplissage des bouteilles à gaz.
2 Références normatives
Les documents suivants sont cités dans le texte de sorte qu’ils constituent, pour tout ou partie de leur
contenu, des exigences du présent document. Pour les références datées, seule l’édition citée s’applique.
Pour les références non datées, la dernière édition du document de référence s’applique (y compris les
éventuels amendements).
ISO 10286, Bouteilles à gaz — Vocabulaire
ISO 14246, Bouteilles à gaz — Robinets de bouteilles à gaz — Essais de fabrication et contrôles
3 Termes et définitions
Pour les besoins du présent document, les termes et les définitions de ISO 10286 ainsi que les suivants
s’appliquent.
L’ISO et l’IEC tiennent à jour des bases de données terminologiques destinées à être utilisées en
normalisation, consultables aux adresses suivantes:
— ISO Online browsing platform: disponible à l’adresse https:// www .iso .org/ obp
— IEC Electropedia: disponible à l’adresse https:// www .electropedia .org/
3.1
contrôle
mode opératoire visant à vérifier qu’un robinet est toujours apte au service
1
© ISO 2022 – Tous droits réservés

---------------------- Page: 6 ----------------------
ISO 22434:2022(F)
3.2
démontage
désassemblage du robinet par séparation de ses composants, entraînant la rupture de sa capacité à
contenir la pression
3.3
dépose
débranchement du robinet de la bouteille à gaz
3.4
maintenance
opérations requises pour conserver le robinet en état de marche
Note 1 à l'article: Il peut s’agir de réparations mineures (3.4.1), de réparations majeures (3.4.2) ou d’une remise en
état (3.4.3).
3.4.1
réparation mineure
opération incluant le nettoyage et le remplacement de composants qui ne sont pas soumis à la pression
EXEMPLE Volant, limiteur de débit de sortie.
3.4.2
réparation majeure
opération incluant le remplacement d’accessoires de robinet situés dans l’enveloppe sous pression mais
ne nécessitant pas un démontage (3.2) du robinet
EXEMPLE Dispositif de décompression (PRD), manomètres, débitmètre, dispositif de pression résiduelle.
3.4.3
remise en état
opération impliquant le démontage (3.2) du robinet, l’évaluation et la réutilisation ou le remplacement
(si nécessaire) de ses composants internes et le remontage du robinet pour le remettre en service
4 Exigences générales
4.1 Fréquence du contrôle et de la maintenance
Si, à un moment, il est décidé de soumettre un robinet à une maintenance – par exemple lors des
contrôles et essais périodiques de la bouteille à gaz – il doit soit faire l’objet d’une maintenance selon 5.3,
soit être mis au rebut conformément à l’Article 8.
4.2 Personnel
Les robinets ne doivent être contrôlés, entretenus et déposés que par un personnel compétent.
4
...

FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 22434
ISO/TC 58/SC 2
Gas cylinders — Inspection and
Secretariat: AFNOR
maintenance of valves
Voting begins on:
2022-12-09
Bouteilles à gaz — Contrôle et maintenance des robinets
Voting terminates on:
2022-02-03
ISO/CEN PARALLEL PROCESSING
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 22434:2022(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © ISO 2022

---------------------- Page: 1 ----------------------
ISO/FDIS 22434:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
  © ISO 2022 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/FDIS 22434:2022(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General requirements . 2
4.1 Frequency of inspection and maintenance . 2
4.2 Personnel . 2
4.3 Safety concerns . 2
5 Inspection and maintenance . 3
5.1 General . 3
5.2 Inspection . 3
5.2.1 General . 3
5.2.2 Cleaning . 3
5.2.3 External examination — Valve remaining in the gas cylinder . 3
5.2.4 Additional external examination — Valve removed from gas cylinder . 4
5.2.5 Acceptance criteria . 4
5.3 Maintenance . 4
5.3.1 Minor repairs . 4
5.3.2 Major repairs . 4
5.3.3 Refurbishment . 5
5.4 Testing . 6
6 Marking . . 6
7 Packaging. 6
8 Scrapping . 6
Bibliography . 7
iii
© ISO 2022 – All rights reserved

---------------------- Page: 3 ----------------------
ISO/FDIS 22434:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 58, Gas cylinders, Subcommittee SC 2,
Cylinder fittings, in collaboration with the European Committee for Standardization (CEN) Technical
Committee CEN/TC 23, Transportable gas cylinders, in accordance with the Agreement on technical
cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 22434:2006), which has been technically
revised. The main changes are as follows:
— the Scope has been revised;
— the Normative references have been updated;
— the Terms and definitions have been updated;
— subclauses 5.1, 5.2.2 and 5.3.2 have been modified;
— Clause 6 “Testing” has been moved to 5.4 and has been modified;
— marking requirements have been modified;
— the Bibliography has been updated.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
 © ISO 2022 – All rights reserved

---------------------- Page: 4 ----------------------
ISO/FDIS 22434:2022(E)
Introduction
[1]
This document has been written so that it is suitable to be referenced in the UN Model Regulations .
v
© ISO 2022 – All rights reserved

---------------------- Page: 5 ----------------------
FINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 22434:2022(E)
Gas cylinders — Inspection and maintenance of valves
1 Scope
This document specifies requirements for the inspection and maintenance of valves [including ball
valves and valves with integrated pressure regulator (VIPRs)] for
a) refillable transportable gas cylinders,
b) cylinder bundles,
c) pressure drums and tubes,
which convey compressed, liquefied or dissolved gases.
This document does not apply to valves for LPG.
NOTE Where there is no risk of ambiguity, gas cylinders, cylinder bundles, pressure drums and tubes are
addressed with the collective term “gas cylinders” within this document.
This document is applicable to valves reused at the time of the periodic inspection of gas cylinders,
cylinder bundles, pressure drums and tubes, and can be applied at any other time, e.g. at a change of gas
service (see ISO 11621).
This document does not apply to the routine inspection of valves, e.g. carried out at the time of a gas
cylinder filling.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 10286, Gas cylinders — Terminology
ISO 14246, Gas cylinders — Cylinder valves — Manufacturing tests and examinations
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 10286 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
3.1
inspection
procedure to determine if a valve is suitable for further service
3.2
dismantling
separation of the valve into its component parts, such that the main pressure barrier of the valve is
breached
1
© ISO 2022 – All rights reserved

---------------------- Page: 6 ----------------------
ISO/FDIS 22434:2022(E)
3.3
removal
disconnection of the valve from the gas cylinder
3.4
maintenance
operations required to keep the valve in working condition
Note 1 to entry: Note to entry: This covers minor repairs (3.4.1), major repairs (3.4.2) and refurbishment (3.4.3).
3.4.1
minor repair
operation including cleaning and
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.