SIST EN 474-9:2007+A1:2009
(Main)Earth-moving machinery - Safety - Part 9: Requirements for pipelayers
Earth-moving machinery - Safety - Part 9: Requirements for pipelayers
This part of EN 474 deals with all significant hazards, hazardous situations and events relevant to pipelayers as defined in EN ISO 6165:2006, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4).
The requirements of this part are complementary to the common requirements formulated in EN 474-1:2006.
This part does not repeat the requirements from EN 474-1:2006, but adds or replaces the requirements for application for pipelayers.
This part specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards, hazardous situations and events during commissioning, operation and maintenance of pipelayers.
This part specifies additional requirements for rear mounted winches.
Pipelayers with rotating upper structure are excluded from the scope of this document. However, specific requirements are under development.
This European Standard is not applicable to pipelayers manufactured before the date of publication of this European Standard by CEN.
Erdbaumaschinen - Sicherheit - Teil 9: Anforderungen für Rohrverleger
Dieser Teil der EN 474 behandelt alle signifikanten Gefährdungen, Gefährdungssituationen und Gefährdungs-ereignisse, die für Rohrverleger zutreffen, wie sie in EN ISO 6165:2006 definiert sind, wenn sie bestimmungs-gemäß verwendet werden. Die nach vernünftigem Ermessen für den Hersteller vorhersehbare Nutzung der Maschine außerhalb der bestimmungsgemäßen Verwendung ist ebenfalls berücksichtigt (siehe Abschnitt 4).
Die Anforderungen gelten ergänzend zu den allgemeinen Anforderungen der !EN 474-1:2006+A1:2009".
Dieser Teil wiederholt nicht die Anforderungen der !EN 474-1:2006+A1:2009", aber ergänzt oder ersetzt diese, sofern sie für den Einsatz von Rohrverlegern von Bedeutung sind.
Dieser Teil beschreibt die geeigneten technischen Maßnahmen, die erforderlich sind, die Risiken, die aufgrund signifikanter Gefährdungen, Gefährdungssituationen und Gefährdungsereignisse, die während der Inbetriebnahme, des Betriebs, der Instandhaltung von Rohrverlegern eintreten können, zu mindern oder zu beseitigen.
Dieser Teil gibt zusätzliche Anforderungen für die heckseitig montierte Winde.
Rohrverleger mit drehbarem Aufbau sind vom Umfang dieses Dokuments ausgenommen. Spezifische Anforderungen sind in Ausarbeitung.
Diese Europäische Norm ist nicht anzuwenden für Rohrverleger, die vor der Veröffentlichung dieser Europäischen Norm durch CEN hergestellt wurden.
Engins de terassement - Sécurité - Partie 9: Prescriptions applicables aux poseurs de canalisations
La présente partie de l’EN 474 traite de tous les phénomènes, situations et événements dangereux significatifs
relatifs aux poseurs de canalisations tels que définis dans l’EN ISO 6165:2006, lorsqu’ils sont utilisés comme prévu
ou dans des conditions de mauvais usage que le fabricant peut raisonnablement prévoir (voir Article 4). La présente
partie donne également des prescriptions relatives aux treuils montés à l’arrière.
Les prescriptions figurant dans la présente partie viennent en complément des prescriptions communes présentées
dans !l’EN 474-1:2006+A1:2009".
La présente partie ne répète pas les prescriptions de !l’EN 474-1:2006+A1:2009" mais en ajoute ou en remplace
certaines applicables aux poseurs de canalisations.
La présente partie prescrit les mesures techniques appropriées pour éliminer ou réduire les risques dus aux
phénomènes, situations et événements dangereux significatifs survenant lors de la mise en service, du
fonctionnement et de la maintenance des poseurs de canalisations.
La présente partie spécifie des prescriptions supplémentaires pour les treuils montés à l’arrière.
Les poseurs de canalisations comportant une superstructure pivotante sont exclus du présent document. Cependant,
des prescriptions spécifiques sont en cours de développement.
La présente Norme européenne n’est pas applicable aux poseurs de canalisations fabriqués !avant" la
publication de la présente Norme européenne par le CEN.
Stroji za zemeljska dela - Varnost - 9. del: Zahteve za stroje za polaganje cevi
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 474-9:2007+A1:2009
01-maj-2009
Stroji za zemeljska dela - Varnost - 9. del: Zahteve za stroje za polaganje cevi
Earth-moving machinery - Safety - Part 9: Requirements for pipelayers
Erdbaumaschinen - Sicherheit - Teil 9: Anforderungen für Rohrverleger
Engins de terassement - Sécurité - Partie 9: Prescriptions applicables aux poseurs de
canalisations
Ta slovenski standard je istoveten z: EN 474-9:2006+A1:2009
ICS:
53.100 Stroji za zemeljska dela Earth-moving machinery
SIST EN 474-9:2007+A1:2009 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 474-9:2007+A1:2009
---------------------- Page: 2 ----------------------
SIST EN 474-9:2007+A1:2009
EUROPEAN STANDARD
EN 474-9:2006+A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2009
ICS 53.100 Supersedes EN 474-9:2006
English Version
Earth-moving machinery - Safety - Part 9: Requirements for
pipelayers
Engins de terassement - Sécurité - Partie 9: Prescriptions Erdbaumaschinen - Sicherheit - Teil 9: Anforderungen für
applicables aux poseurs de canalisations Rohrverleger
This European Standard was approved by CEN on 17 April 2006 and includes Amendment 1 approved by CEN on 20 December 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 474-9:2006+A1:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 474-9:2007+A1:2009
EN 474-9:2006+A1:2009 (E)
Contents Page
Foreword .3
Introduction .5
1 Scope .6
2 Normative references .6
3 Terms and definitions .7
4 List of additional significant hazards .7
5 Safety requirements and/or measures .7
5.1 General .7
5.2 Operator’s station .8
5.3 Stability and lifting equipment .8
5.4 Rear mounted winch .9
5.5 Noise .9
6 Information for use . 10
6.1 Warning signs . 10
6.2 Operation manual . 10
6.3 Machine marking. 10
Annex A (normative) List of additional significant hazards – Pipelayers . 11
Annex B (informative) Illustrations . 12
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 98/37/EC . 14
Annex ZB (informative) !!!!Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC"""" . 15
Bibliography . 16
Figures
Figure B.1 — Crawler pipelayer . 12
Figure B.2 — Wheel pipelayer . 12
Figure B.3 — Pipelayer side view . 13
Figure B.4 — Crawler pipelayer with a rotating upper structure . 13
Tables
Table A.1 — List of additional significant hazards . 11
2
---------------------- Page: 4 ----------------------
SIST EN 474-9:2007+A1:2009
EN 474-9:2006+A1:2009 (E)
Foreword
This document (EN 474-9:2006+A1:2009) has been prepared by Technical Committee CEN/TC 151
“Construction equipment and building material machines — Safety”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by August 2009, and conflicting national standards shall be withdrawn at
the latest by December 2009.
This document includes Amendment 1, approved by CEN on 2008-12-20.
This document supersedes !EN 474-9:2006".
The start and finish of text introduced or altered by amendment is indicated in the text by tags ! ".
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive.
!For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document."
For bibliographic references, see !EN 474-1:2006+A1:2009".
EN 474 "Earth-moving machinery — Safety" comprises the following parts:
Part 1: General requirements
Part 2: Requirements for tractor-dozers
Part 3: Requirements for loaders
Part 4: Requirements for backhoe-loaders
Part 5: Requirements for hydraulic excavators
Part 6: Requirements for dumpers
Part 7: Requirements for scrapers
Part 8: Requirements for graders
Part 9: Requirements for pipelayers
Part 10: Requirements for trenchers
Part 11: Requirements for earth and landfill compactors
Part 12: Requirements for cable excavators
This European Standard is intended for use in combination with Part 1 of the series.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
3
---------------------- Page: 5 ----------------------
SIST EN 474-9:2007+A1:2009
EN 474-9:2006+A1:2009 (E)
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and United Kingdom.
4
---------------------- Page: 6 ----------------------
SIST EN 474-9:2007+A1:2009
EN 474-9:2006+A1:2009 (E)
Introduction
This part of EN 474 is a type C standard as stated in EN ISO 12100-1:2003.
The machinery concerned and the extent to which hazards, hazardous situations and events are covered are
indicated in the scope of this European Standard.
When provisions of this type C standard are different from those which are stated in type A or B standards, the
provisions of this type C standard take precedence over the provisions of the other standards, for machines
that have been designed and built according to the provisions of this type C standard.
5
---------------------- Page: 7 ----------------------
SIST EN 474-9:2007+A1:2009
EN 474-9:2006+A1:2009 (E)
1 Scope
This part of EN 474 deals with all significant hazards, hazardous situations and events relevant to pipelayers
as defined in EN ISO 6165:2006, when they are used as intended and under conditions of misuse which are
reasonably foreseeable by the manufacturer (see Clause 4).
The requirements of this part are complementary to the common requirements formulated in
!EN 474-1:2006+A1:2009".
This part does not repeat the requirements from !EN 474-1:2006+A1:2009", but adds or replaces the
requirements for application for pipelayers.
This part specifies the appropriate technical measures to eliminate or reduce risks arising from the significant
hazards, hazardous situations and events during commissioning, operation and maintenance of pipelayers.
This part specifies additional requirements for rear mounted winches.
Pipelayers with rotating upper structure are excluded from the scope of this document. However, specific
requirements are under development.
This European Standard is not applicable to pipelayers manufactured before the date of publication of this
European Standard by CEN.
2 Normative references
The following referenced documents are indispensable for the application of this European Standard. For
dated references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
!EN 474-1:2006+A1:2009", Earth-moving machinery — Safety — Part 1: General requirements
EN 1032:2003, Mechanical vibration — Testing of mobile machinery in order to determine the vibration
emission value
EN 1677-1:2000, Components for slings — Safety — Part 1: Forged steel components, Grade 8
EN 1677-2:2000, Components for slings — Safety — Part 2: Forged steel lifting hook
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.