SIST EN 60728-7-3:2010

Cable networks for television signals, sound signals and interactive services - Part 7-3: Hybrid fibre coax outside plant status monitoring - Power Supply to Transponder Interface Bus (PSTIB) specification (IEC 60728-7-3:2009)

This part of IEC 60728 specifies requirements for the Hybrid Fibre Coax (HFC) Outside Plant (OSP) Power Supplies (PS). This standard is part of a series developed to support the design and implementation of interoperable management systems for evolving HFC cable networks. The purpose of the standards is to support the design and implementation of interoperable management systems for evolving HFC cable networks. The Power Supply to Transponder Interface Bus (PSTIB) specification describes the physical (PHY) interface and related messaging and protocols implemented at the Data Link Layer (DLL), layers 1 and 2 respectively in the 7-layer ISO-OSI reference model, that support communications between compliant transponders and the managed OSP power supplies and other related power equipment to which they interface. This standard describes the PSTIB PHY and DLL layer requirements and protocols that shall be implemented to support reliable communications between all type 2 and type 3 compliant OSP transponders on the HFC plant and managed OSP power supplies and related hardware. Any exceptions to compliance with this standard will be specifically noted as necessary.

Kabelnetze für Fernsehsignale, Tonsignale und interaktive Dienste - Teil 7-3: Zustandsüberwachung Hybrid-Faser-Koax-Netze (HFC) - Schnittstellenbus von Fernspeise-Stromversorgung zu Transponder (PSTIB) (IEC 60728-7-3:2009)

Réseaux de distribution par câbles pour signaux de télévision, signaux de radiodiffusion sonore et services interactifs - Partie 7-3: Surveillance de l'état des installations extérieures des réseaux hybrides à fibre optique et câble coaxial - Spécification de l'alimentation du bus d'interface du répéteur (CEI 60728-7-3:2009)

L'IEC 60728-7-3:2009 définit les exigences relatives aux alimentations (PS) des installations extérieures (OSP) des réseaux hybrides à fibre optique et câble coaxial (HFC). La présente norme fait partie d'une série de normes élaborées pour prendre en charge la conception et la mise en œuvre des systèmes de gestion interopérables pour les réseaux évolutifs de distribution par câbles HFC. L'objet de ces normes est de prendre en charge la conception et la mise en œuvre des systèmes de gestion interopérables pour les réseaux évolutifs de distribution par câbles HFC. La spécification de l'alimentation du bus d'interface du répéteur (PSTIB) décrit l'interface physique (PHY) ainsi que les messages et protocoles associés mis en œuvre respectivement au niveau de la première et de la deuxième couche de la couche liaison de données (DLL) dans le modèle de référence ISO-OSI à 7 couches. Ces messages et protocoles prennent en charge les communications entre les répéteurs conformes et les alimentations OSP gérées et les autres équipements de puissance associés avec lesquels ils s'interfacent.
La présente norme décrit les exigences relatives à l'interface PHY et à la couche DLL de la PSTIB, ainsi que les protocoles qui doivent être mis en œuvre pour prendre en charge des communications fiables entre tous les répéteurs OSP conformes de type 2 et de type 3 de l'installation HFC et les alimentations OSP gérées et le matériel associé. Toute exception de conformité à la présente norme est expressément mentionnée, selon les besoins.
L'IEC 60728-7-3:2009 annule et remplace la première édition parue en 2003, dont elle constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:
• toutes les modifications de la norme ANSI/SCTE 25-3 v1.0 à la norme ANSI/SCTE 25 3 v1.1 (2005) ont été prises en compte dans cette deuxième édition;
• l'Article 7 est fondé sur la norme ANSI/SCTE 110 (2005);
• l'Annexe A informative concernant la sous-couche de gestion hybride a été ajoutée.

Kabelska omrežja za televizijske in zvokovne signale ter interaktivne storitve - 7-3. del: Nadzorovanje stanja zunanjih inštalacij omrežij hibridnih optično-koaksialnih kablov - Specifikacija napajalnika za vodilo vmesnika transponderja (PSTIB) (IEC 60728-7-3:2009)

Ta del IEC 60728 določa zahteve za napajalnik (PS) zunanjih (OSP) hibridnih optično-koaksialnih (HFC) inštalacij. Ta standard je del serije, razvite za podporo načrtovanju in izvedbi interoperabilnih nadzornih sistemov za razvoj HFC kabelskih omrežij. Namen standardov je podpora načrtovanju in izvedbi interoperabilnih nadzornih sistemov za razvoj HFC kabelskih omrežij. Specifikacija napajalnika za vodilo vmesnika transponderja(PSTIB) opisuje fizični (PHY) vmesnik in povezana sporočila ter protokole, izvedene na sloju podatkovnega vmesnika (DLL), slojih 1 in 2 v tem zaporedju v 7-slojnem ISO-OSI referenčnem modelu, ki podpirata komunikacijo med skladnimi transponderji in nadzorovanimi OSP napajalniki ter ostalo sorodno opremo, s katero so povezani. Ta standard opisuje zahteve in protokole za PSTIB PHY in DLL sloj, ki bodo izvedeni za podporo zanesljivi komunikaciji med vsemi OSP transponderji, skladnimi s tipom 2 in tipom 3 na HFC opremi in ki bodo nadzorovali OSP napajalnike ter sorodno strojno opremo. Vsako odstopanje od skladnosti s tem standardom bo po potrebi zabeleženo posebej.

General Information

• Status: Published
• Publication Date: 23-Dec-2009
• ICS: 33.060.40 - Cabled distribution systems
• ICS: 35.100.20 - Data link layer
• Technical Committee: AVM - Audio, video and multimedia systems and equipment
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 09-Dec-2009
• Due Date: 13-Feb-2010
• Completion Date: 24-Dec-2009
• Ref Project: EN 60728-7-3:2009 - Cable networks for television signals, sound signals and interactive services - Part 7-3: Hybrid fibre coax outside plant status monitoring - Power supply to transponder interface bus (PSTIB)

Relations

• Replaces: SIST EN 60728-7-3:2006 - Cable networks for television signals, sound signals and interactive services -- Part 7-3: Hybrid Fibre Coax Outside Plant Status Monitoring - Power supply to Transponder Interface Bus (PSTIB) Specification
• Effective Date: 01-Feb-2010
• Revised: SIST EN 60728-7-3:2006 - Cable networks for television signals, sound signals and interactive services -- Part 7-3: Hybrid Fibre Coax Outside Plant Status Monitoring - Power supply to Transponder Interface Bus (PSTIB) Specification
• Effective Date: 06-Nov-2012
• Replaces: SIST EN 60728-7-3:2006 - Cable networks for television signals, sound signals and interactive services -- Part 7-3: Hybrid Fibre Coax Outside Plant Status Monitoring - Power supply to Transponder Interface Bus (PSTIB) Specification
• Effective Date: 28-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60728-7-3:2010
01-februar-2010
1DGRPHãþD
SIST EN 60728-7-3:2006
.DEHOVNDRPUHåMD]DWHOHYL]LMVNHLQ]YRNRYQHVLJQDOHWHULQWHUDNWLYQHVWRULWYH
GHO1DG]RURYDQMHVWDQMD]XQDQMLKLQãWDODFLMRPUHåLMKLEULGQLKRSWLþQRNRDNVLDOQLK
NDEORY6SHFLILNDFLMDQDSDMDOQLND]DYRGLORYPHVQLNDWUDQVSRQGHUMD367,%,(&

Cable networks for television signals, sound signals and interactive services - Part 7-3:
Hybrid fibre coax outside plant status monitoring - Power Supply to Transponder
Interface Bus (PSTIB) specification (IEC 60728-7-3:2009)
Kabelnetze für Fernsehsignale, Tonsignale und interaktive Dienste - Teil 7-3:
Zustandsüberwachung Hybrid-Faser-Koax-Netze (HFC) - Schnittstellenbus von
Fernspeise-Stromversorgung zu Transponder (PSTIB) (IEC 60728-7-3:2009)
Réseaux de distribution par câbles pour signaux de télévision, signaux de radiodiffusion
sonore et services interactifs - Partie 7-3: Surveillance de l'état des installations
extérieures des réseaux hybrides à fibre optique et câble coaxial - Spécification de
l'alimentation du bus d'interface du répéteur (CEI 60728-7-3:2009)
Ta slovenski standard je istoveten z: EN 60728-7-3:2009
ICS:
33.060.40 Kabelski razdelilni sistemi Cabled distribution systems
35.100.20 Podatkovni povezovalni sloj Data link layer
SIST EN 60728-7-3:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60728-7-3:2010

---------------------- Page: 2 ----------------------

SIST EN 60728-7-3:2010

EUROPEAN STANDARD
EN 60728-7-3

NORME EUROPÉENNE
December 2009
EUROPÄISCHE NORM

ICS 33.040; 33.160 Supersedes EN 60728-7-3:2005

English version

Cable networks for television signals,
sound signals and interactive services -
Part 7-3: Hybrid fibre coax outside plant status monitoring -
Power supply to transponder interface bus (PSTIB)
(IEC 60728-7-3:2009)


Réseaux de distribution par câbles  Kabelnetze für Fernsehsignale,
pour signaux de télévision, Tonsignale und interaktive Dienste -
signaux de radiodiffusion sonore Teil 7-3: Zustandsüberwachung
et services interactifs - Hybrid-Faser-Koax-Netze (HFC) -
Partie 7-3: Surveillance de l'état Schnittstellenbus von Fernspeise-
des installations extérieures Stromversorgung zu Transponder (PSTIB)
des réseaux hybrides à fibre optique et (IEC 60728-7-3:2009)
câble coaxial -
Alimentation du bus d'interface
du répéteur
(CEI 60728-7-3:2009)


This European Standard was approved by CENELEC on 2009-11-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: Avenue Marnix 17, B - 1000 Brussels


© 2009 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60728-7-3:2009 E

---------------------- Page: 3 ----------------------

SIST EN 60728-7-3:2010
EN 60728-7-3:2009 - 2 -
Foreword
The text of document 100/1464/CDV, future edition 2 of IEC 60728-7-3, prepared by technical area 5:
Cable networks for television signals, sound signals and interactive services, of IEC TC 100, Audio, video
and multimedia systems and equipment, was submitted to the IEC-CENELEC parallel vote and was
approved by CENELEC as EN 60728-7-3 on 2009-11-01.
This European Standard supersedes EN 60728-7-3:2005.
EN 60728-7-3:2009 includes the following significant technical changes with respect to
EN 60728-7-3:2005:
– all changes from standard ANSI/SCTE 25-3 v1.0 to standard ANSI/SCTE 25-3 v1.1 (2005) have been
taken into account in EN 60728-7-3:2009;
– Clause 7 is based on standard ANSI/SCTE 110 (2005);
– addition of informative Annex A concerning hybrid management sub-layer.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2010-08-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2012-11-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60728-7-3:2009 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60728-7-1 NOTE  Harmonized as EN 60728-7-1:2005 (not modified).
IEC 60728-7-2 NOTE  Harmonized as EN 60728-7-2:2005 (not modified).
IEC 60728-7-3 NOTE  Harmonized as EN 60728-7-3:2005 (not modified).
__________

---------------------- Page: 4 ----------------------

SIST EN 60728-7-3:2010
- 3 - EN 60728-7-3:2009

Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

1) 2)
IEC 60603-7 - Connectors for electronic equipment - EN 60603-7 2009
Part 7: Detail specification for 8-way,
unshielded, free and fixed connectors




1)
Undated reference.
2)
Valid edition at date of issue.

---------------------- Page: 5 ----------------------

SIST EN 60728-7-3:2010

---------------------- Page: 6 ----------------------

SIST EN 60728-7-3:2010

IEC 60728-7-3
®
Edition 2.0 2009-10
INTERNATIONAL
STANDARD

colour
inside

Cable networks for television signals, sound signals and interactive services –
Part 7-3: Hybrid fibre coax outside plant status monitoring – Power supply to
transponder interface bus (PSTIB)


INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
W
ICS 33.040; 33.160 ISBN 2-8318-1065-1
® Registered trademark of the International Electrotechnical Commission

---------------------- Page: 7 ----------------------

SIST EN 60728-7-3:2010
– 2 – 60728-7-3 © IEC:2009(E)
CONTENTS
FOREWORD.5
INTRODUCTION.7
1 Scope.8
2 Normative references .9
3 Terms, definitions and abbreviations .9
3.1 Terms and definitions .9
3.2 Abbreviations .10
4 Reference architecture forward and return channel specifications .10
5 Power supply to transponder interface bus specification overview .11
5.1 General .11
5.2 Interface compliance .11
5.3 Implementation compliance .11
5.4 Revision control .12
6 Power supply to transponder interface bus – Physical layer specification .12
6.1 Interface requirements .12
6.1.1 Connector type .12
6.1.2 Communications interface .12
6.1.3 Connector signals.12
6.1.4 Transponder power.12
6.1.5 Line balance.13
6.1.6 Cable length .13
6.1.7 Data encoding .13
6.1.8 Bit rate .13
6.1.9 Duplex.13
6.1.10 Method of communications .13
6.1.11 Indicators .13
6.2 Interface diagram .14
7 Alternative power supply to transponder interface bus – Physical layer
specification .15
7.1 Introduction to alternative.15
7.2 Interface requirements .15
7.2.1 Connector type .15
7.2.2 Communications interface .15
7.2.3 Connector signals.15
7.2.4 Transponder power.15
7.2.5 Line balance.16
7.2.6 Cable length .16
7.2.7 Data encoding .16
7.2.8 Bit rate .16
7.2.9 Duplex.16
7.2.10 Method of communication.16
7.2.11 Indicators .17
7.3 Interface diagram .17
8 Power supply to transponder interface bus – Data link layer specification.18
8.1 DLL packet structure .18

---------------------- Page: 8 ----------------------

SIST EN 60728-7-3:2010
60728-7-3 © IEC:2009(E) – 3 –
8.1.1 General .18
8.1.2 Start .18
8.1.3 Destination Address .18
8.1.4 Source Address .19
8.1.5 Identification.19
8.1.6 Datagram .19
8.1.7 End .19
8.1.8 Checksum .19
8.2 DLE sequence.19
8.3 Interface timing .20
8.3.1 Message synchronization and interaction .20
8.3.2 Transmission timing requirements .21
8.4 DLL datagrams.22
8.4.1 Structure .22
8.4.2 Resolution versus accuracy .23
8.4.3 DLL datagram types .23
Annex A (informative) HMS specification documents.37
Bibliography.38

Figure 1 – Reference architecture diagram .11
Figure 2 – Sample PSTIB RS-485 interface .14
Figure 3 – Sample PSTIB RS-485 interface .17
Figure 4 – DLL packet structure .18
Figure 5 – PSTIB data and timing diagram.21
Figure 6 – DLL datagram structure.22
Figure 7 – Battery string naming conventions.33

Table 1 – Transponder type classifications .8
Table 2 – RJ-45 Connector pin assignment.12
Table 3 – Sample PSTIB RS-485 interface – Reference signals.14
Table 4 – RJ-45 Connector pin assignment.15
Table 5 – Sample PSTIB RS-485 interface – Reference signals.17
Table 6 – Generic DLL packet structure .18
Table 7 – Reserved destination address ranges.19
Table 8 – PSTIB timing specifications .21
Table 9 – Generic DLL datagram structure.22
Table 10 – DLL datagrams.24
Table 11 – Command: Get_Configuration datagram.24
Table 12 – Response: Get_Configuration datagram .25
Table 13 – Response: Get_Configuration datagram variable binding (general).25
Table 14 – Response: Get_Configuration datagram variable binding (power supply).26
a
Table 15 – Response: Get_Configuration datagram variable binding (generator) .29
Table 16 – Command: Get_Power_Supply_Data datagram .30
Table 17 – Response: Get_Power_Supply_Data datagram .30
Table 18 – Response: Get_Power_Supply_Data datagram variable binding.30

---------------------- Page: 9 ----------------------

SIST EN 60728-7-3:2010
– 4 – 60728-7-3 © IEC:2009(E)
Table 19 – Command: Power_Supply_Control datagram.33
Table 20 – Command: Get_Generator_Data datagram.33
Table 21 – Response: Get_Generator_Data datagram .34
Table 22 – Response: Get_Generator_Data Datagram variable binding .34
Table 23 – Command: Generator_Control datagram .35
Table 24 – Response: Invalid_Request datagram .35
Table 25 – Response: Request_Processed datagram .36
Table A.1 – HMS document family .37

---------------------- Page: 10 ----------------------

SIST EN 60728-7-3:2010
60728-7-3 © IEC:2009(E) – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

CABLE NETWORKS FOR TELEVISION SIGNALS,
SOUND SIGNALS AND INTERACTIVE SERVICES –

Part 7-3: Hybrid fibre coax outside plant status monitoring –
Power supply to transponder interface bus (PSTIB)


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote interna-
tional co-operation on all questions concerning standardization in the electrical and electronic fields. To this
end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Techni-
cal Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”).
Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject
dealt with may participate in this preparatory work. International, governmental and non-governmental organiza-
tions liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Or-
ganization for Standardization (ISO) in accordance with conditions determined by agreement between the two
organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all inter-
ested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinter-
pretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence be-
tween any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and ex-
penses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publica-
tions.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of pat-
ent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60728-7-3 has been prepared by technical area 5: Cable networks
for television signals, sound signals and interactive services, of IEC technical committee 100:
Audio, video and multimedia systems and equipment.
This second edition cancels and replaces the first edition published in 2003 of which it consti-
tutes a technical revision. This edition includes the following significant technical changes
with respect to the previous edition:
• All changes from standard ANSI/SCTE 25-3 v1.0 to standard ANSI/SCTE 25-3 v1.1 (2005)
have been taken into account in this second edition.
• Clause 7 is based on standard ANSI/SCTE 110 (2005).
• Addition of informative Annex A concerning hybrid management sub-layer.

---------------------- Page: 11 ----------------------

SIST EN 60728-7-3:2010
– 6 – 60728-7-3 © IEC:2009(E)
The text of this standard is based on the following documents:
CDV Report on voting
100/1464/CDV 100/1599/RVC

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of the IEC 60728 series, under the general title Cable networks for television
signals, sound signals and interactive services, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.


IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates that it contains
colours which are considered to be useful for the correct understanding of its contents. Users
should therefore print this document using a colour printer.

---------------------- Page: 12 ----------------------

SIST EN 60728-7-3:2010
60728-7-3 © IEC:2009(E) – 7 –
INTRODUCTION
Standards of the IEC 60728 series deal with cable networks including equipment and associ-
ated methods of measurement for headend reception, processing and distribution of television
signals, sound signals and their associated data signals and for processing, interfacing and
transmitting all kinds of signals for interactive services using all applicable transmission me-
dia.
This includes
1
• CATV -networks;
• MATV-networks and SMATV-networks;
• individual receiving networks;
and all kinds of equipment, systems and installations installed in such networks.
The extent of this standardization work is from the antennas and/or special signal source in-
puts to the head-end or other interface points to the network up to the terminal input.
The standardization of any user terminals (i.e. tuners, receivers, decoders, multimedia termi-
nals, etc.) as well as of any coaxial, balanced and optical cables and accessories thereof is
excluded.
The following differences exist in some countries:
The Japanese de facto standard (NCTEA S-006) concerning requirements for the HFC out-
side plant management, which was published in 1995, has already been available in Japan.
The purpose of this standard is to support the design and implementation of interoperable
management systems for HFC cable networks used in Japan.


___________
1
This word encompasses the HFC networks used nowadays to provide telecommunications services, voice,

data, audio and video both broadcast and narrowcast.

---------------------- Page: 13 ----------------------

SIST EN 60728-7-3:2010
– 8 – 60728-7-3 © IEC:2009(E)
CABLE NETWORKS FOR TELEVISION SIGNALS,
SOUND SIGNALS AND INTERACTIVE SERVICES –

Part 7-3: Hybrid fibre coax outside plant status monitoring –
Power supply to transponder interface bus (PSTIB)



1 Scope
This part of IEC 60728 specifies requirements for the Hybrid Fibre Coax (HFC) Outside Plant
(OSP) Power Supplies (PS). This standard is part of a series developed to support the design
and implementation of interoperable management systems for evolving HFC cable networks.
The purpose of the standards is to support the design and implementation of interoperable
management systems for evolving HFC cable networks. The Power Supply to Transponder In-
terface Bus (PSTIB) specification describes the physical (PHY) interface and related messag-
ing and protocols implemented at the Data Link Layer (DLL), layers 1 and 2 respectively in the
7-layer ISO-OSI reference model, that support communications between compliant trans-
ponders and the managed OSP power supplies and other related power equipment to which
they interface.
This standard describes the PSTIB PHY and DLL layer requirements and protocols that shall
be implemented to support reliable communications between all type 2 and type 3 compliant
OSP transponders on the HFC plant and managed OSP power supplies and related hardware.
Any exceptions to compliance with this standard will be specifically noted as necessary.
Transponder type classifications referenced within the HMS series of standards are defined in
Table 1.
Table 1 – Transponder type classifications
Type Description Application
• This transponder interfaces with legacy network
equipment through proprietary means.
Refers to legacy transponder equip-
Type 0
ment which is incapable of supporting
• This transponder could be managed through the
the specifications
same management applications as the other types
through proxies or other means at the head-end.
• This transponder interfaces with legacy network
equipment through proprietary means.
Refers to stand-alone transponder
equipment (legacy or new), which can
• Type 1 is a standards-compliant transponder (either
Type 1
be upgraded to support the specifica-
manufactured to the standard or upgraded) that con-
tions
nects to legacy network equipment via a proprietary
interface.
• This transponder interfaces with network equipment
designed to support the electrical and physical
specifications defined in the standards.
Refers to a stand-alone, compliant
Type 2
transponder
• It can be factory or field-installed.
• Its RF connection is independent of the monitored
NE.
• This transponder interfaces with network equipment
designed to support the electrical specifications de-
fined in the standards.
• It may or may not support the physical specifications
Refers to a stand-alone or embedded,
Type 3
defined in the standards.
compliant transponder
• It can be factory-installed. It may or may not be
field-installed.
• Its RF connection is through the monitored NE.

---------------------- Page: 14 ----------------------

SIST EN 60728-7-3:2010
60728-7-3 © IEC:2009(E) – 9 –
A list of documents in the HMS specifications family is provided in informative Annex A.
2 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
IEC 60603-7, Connectors for electronic equipment – Part 7: Detail specification for 8-way, un-
shielded, free and fixed connectors
3 Terms, definitions and abbreviations
3.1 Terms and definitions
For the
...