SIST EN IEC 60352-5:2020
(Main)Solderless connections - Part 5: Press-in connections - General requirements, test methods and practical guidance (IEC 60352-5:2020)
Solderless connections - Part 5: Press-in connections - General requirements, test methods and practical guidance (IEC 60352-5:2020)
This part of IEC 60352 is applicable to solderless press-in connections for use in electrical
and electronic equipment and components.
The press-in connection consists of a termination having a suitable press-in zone which is
inserted into a hole of a board.
Information on materials and data from industrial experience is included in addition to the test
procedures to provide electrically stable connections under specified environmental conditions.
The object of this document is to determine the suitability of press-in connections under
mechanical, electrical and atmospheric conditions as specified by the manufacturer of the
press-in termination and to provide a means of comparing test results when the tools used to
make the connections are of different designs or manufacture.
Lötfreie Verbindungen - Teil 5: Einpressverbindungen - Allgemeine Anforderungen, Prüfverfahren und Anwendungshinweise (IEC 60352-5:2020)
Connexions sans soudure - Partie 5: Connexions insérées à force - Exigences générales, méthodes d'essai et guide pratique (IEC 60352-5:2020)
IEC 60352-5:2020 s’applique aux connexions press-in sans soudure pour utilisation dans les équipements et composants électriques et électroniques.
La connexion press-in consiste en une terminaison ayant une zone de press-in appropriée qui est insérée dans un trou d’une planche.
Les informations sur les matériaux et les données provenant de l’expérience industrielle sont incluses en plus des procédures d’essai pour fournir des connexions électriques stables dans des conditions environnementales spécifiques.
L’objet du présent document est de déterminer la pertinence des connexions de presse dans des conditions mécaniques, électriques et atmosphériques telles que spécifiées par le fabricant de la terminaison presse-in et de fournir un moyen de comparer les résultats des essais lorsque les outils utilisés pour effectuer les connexions sont de conceptions ou de fabrications différentes.
Cette cinquième édition annule et remplace la quatrième édition publiée en 2012. Cette édition constitue une révision technique.
Cette édition comprend les changements importants suivants par rapport à l’édition précédente :
a) révision du domaine d’application en supprimant dans le premier alinéa l’expression "…dans les équipements de télécommunication et les systèmes électroniques employant des techniques similaires" et en la remplaçant par l’expression "…dans les équipements et composants électriques et électroniques";
b) ajout des termes "carte", "trou" et "carte métallique", et des définitions associées, pour stipuler que les bornes pour connexion insérée à force sont utilisées sur des cartes non imprimées fabriquées dans différents matériaux;
c) modifications éditoriales clarifiant la différence entre le programme d’essais de qualification et le programme d’essais d’application;
d) modification de la limite supérieure d’épaisseur de cuivre du trou métallisé, afin de refléter les tendances réelles du marché et les pratiques de fabrication;
e) suppression de l’essai de courbure, celui-ci ciblant plus spécifiquement des applications de la technologie d’insertion à force qui ne sont plus très répandues;
f) ajout de graphiques visant à documenter la force d’insertion et la force d’extraction, car cela constitue une pratique d’essai courante et donne des informations supplémentaires sur les performances mécaniques de la zone de contact;
g) réduction du nombre de spécimens exigés, car un lot d’échantillons d’essai avait été ignoré dans le schéma d’essais précédent;
h) nouvelle formulation en 4.5 pour les bornes fissurées ou pliées;
i) ajout de la Figure 7b pour représenter les points de connexion pour la mesure de la tension et du courant lorsque la borne pour connexion insérée à force ne dépasse pas de la face inférieure de la carte.
Spoji brez spajke - 5. del: Vtisnjeni spoji - Splošne zahteve, preskusne metode in praktični napotki (IEC 60352-5:2020)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN IEC 60352-5:2020
01-november-2020
Nadomešča:
SIST EN 60352-5:2012
SIST EN 60352-5:2012/AC:2015
Spoji brez spajke - 5. del: Vtisnjeni spoji - Splošne zahteve, preskusne metode in
praktični napotki (IEC 60352-5:2020)
Solderless connections - Part 5: Press-in connections - General requirements, test
methods and practical guidance (IEC 60352-5:2020)
Lötfreie Verbindungen - Teil 5: Einpressverbindungen - Allgemeine Anforderungen,
Prüfverfahren und Anwendungshinweise (IEC 60352-5:2020)
Connexions sans soudure - Partie 5: Connexions insérées à force - Exigences
générales, méthodes d'essai et guide pratique (IEC 60352-5:2020)
Ta slovenski standard je istoveten z: EN IEC 60352-5:2020
ICS:
29.120.20 Spojni elementi Connecting devices
SIST EN IEC 60352-5:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN IEC 60352-5:2020
---------------------- Page: 2 ----------------------
SIST EN IEC 60352-5:2020
EUROPEAN STANDARD EN IEC 60352-5
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2020
ICS 31.220.10 Supersedes EN 60352-5:2012 and all of its amendments
and corrigenda (if any)
English Version
Solderless connections - Part 5: Press-in connections - General
requirements, test methods and practical guidance
(IEC 60352-5:2020)
Connexions sans soudure - Partie 5: Connexions insérées Lötfreie Verbindungen - Teil 5: Einpressverbindungen -
à force - Exigences générales, méthodes d'essai et guide Allgemeine Anforderungen, Prüfverfahren und
pratique Anwendungshinweise
(IEC 60352-5:2020) (IEC 60352-5:2020)
This European Standard was approved by CENELEC on 2020-08-26. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60352-5:2020 E
---------------------- Page: 3 ----------------------
SIST EN IEC 60352-5:2020
EN IEC 60352-5:2020 (E)
European foreword
The text of document 48B/2810/FDIS, future edition 5 of IEC 60352-5, prepared by SC 48B "Electrical
connectors" of IEC/TC 48 "Electrical connectors and mechanical structures for electrical and electronic
equipment" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN IEC 60352-5:2020.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-05-26
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2023-08-26
document have to be withdrawn
This document supersedes EN 60352-5:2012 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 60352-5:2020 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60352-1 NOTE Harmonized as EN 60352-1
IEC 61249 (series) NOTE Harmonized as EN 61249 (series)
IEC 61249-2-4 NOTE Harmonized as EN 61249-2-4
2
---------------------- Page: 4 ----------------------
SIST EN IEC 60352-5:2020
EN IEC 60352-5:2020 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60068-1 - Environmental testing - Part 1: General EN 60068-1 -
and guidance
IEC 60512-1 - Connectors for electrical and electronic EN IEC 60512-1 -
equipment - Tests and measurements -
Part 1: Generic specification
IEC 60512-1-1 - Connectors for electronic equipment - EN 60512-1-1 -
Tests and measurements - Part 1-1:
General examination - Test 1a: Visual
examination
IEC 60512-1-2 - Connectors for electronic equipment - EN 60512-1-2 -
Tests and measurements - Part 1-2:
General examination - Test 1b:
Examination of dimension and mass
IEC 60512-2-1 - Connectors for electronic equipment - EN 60512-2-1 -
Tests and measurements - Part 2-1:
Electrical continuity and contact resistance
tests - Test 2a: Contact resistance -
Millivolt level method
IEC 60512-2-5 - Connectors for electronic equipment - EN 60512-2-5 -
Tests and measurements - Part 2-5:
Electrical continuity and contact resistance
tests - Test 2e: Contact disturbance
IEC 60512-6-4 - Connectors for electronic equipment - EN 60512-6-4 -
Tests and measurements - Part 6-4:
Dynamic stress tests - Test 6d: Vibration
(sinusoidal)
IEC 60512-11-1 - Connectors for electrical and electronic EN IEC 60512-11-1 -
equipment - Tests and measurements -
Part 11-1: Climatic tests - Test 11a -
Climatic sequence
IEC 60512-11-4 - Connectors for electronic equipment - EN 60512-11-4 -
Tests and measurements - Part 11-4:
Climatic tests - Test 11d: Rapid change of
temperature
3
---------------------- Page: 5 ----------------------
SIST EN IEC 60352-5:2020
EN IEC 60352-5:2020 (E)
Publication Year Title EN/HD Year
IEC 60512-11-9 - Connectors for electronic equipment - EN 60512-11-9 -
Tests and measurements - Part 11-9:
Climatic tests - Test 11i: Dry heat
IEC 61188-5-1 - Printed boards and printed board EN 61188-5-1 -
assemblies - Design and use - Part 5-1:
Attachment (land/joint) considerations -
Generic requirements
IEC 62326-4 - Printed boards - Part 4: Rigid multilayer EN 62326-4 -
printed boards with interlayer connections -
Sectional specification
4
---------------------- Page: 6 ----------------------
SIST EN IEC 60352-5:2020
IEC 60352-5
®
Edition 5.0 2020-07
INTERNATIONAL
STANDARD
Solderless connections –
Part 5: Press-in connections – General requirements, test methods and practical
guidance
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 31.220.10 ISBN 978-2-8322-8476-6
Warning! Make sure that you obtained this publication from an authorized distributor.
® Registered trademark of the International Electrotechnical Commission
---------------------- Page: 7 ----------------------
SIST EN IEC 60352-5:2020
– 2 – IEC 60352-5:2020 © IEC 2020
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 8
4 Requirements . 10
4.1 General . 10
4.2 Tools . 10
4.2.1 General . 10
4.2.2 Tools evaluation . 10
4.3 Press-in terminations . 10
4.3.1 Materials . 10
4.3.2 Dimensions of the press-in zone . 10
4.3.3 Surface finishes . 10
4.4 Test boards . 11
4.4.1 General . 11
4.4.2 Materials . 11
4.4.3 Thickness of test boards . 11
4.4.4 Hole. 11
4.4.5 Plated-through hole . 12
4.5 Press-in connections . 13
4.6 Manufacturer´s specification . 14
5 Tests . 15
5.1 General remarks . 15
5.1.1 General . 15
5.1.2 Standard conditions for testing . 15
5.1.3 Mounting of specimens . 15
5.2 Test and measuring methods . 16
5.2.1 General examination . 16
5.2.2 Mechanical tests . 16
5.2.3 Contact resistance measurements . 19
5.2.4 Climatic tests . 20
5.3 Test schedules . 21
5.3.1 General . 21
5.3.2 Qualification test schedule . 21
5.3.3 Flow chart . 23
5.3.4 Application test schedule . 24
5.4 Test report . 25
5.4.1 Qualification test report . 25
5.4.2 Application test report . 26
Annex A (informative) Practical guidance . 27
A.1 General . 27
A.2 Current-carrying capacity . 27
A.3 Tool information . 27
A.3.1 Termination insertion tool . 27
A.3.2 Support block . 27
---------------------- Page: 8 ----------------------
SIST EN IEC 60352-5:2020
IEC 60352-5:2020 © IEC 2020 – 3 –
A.3.3 Termination removal tool . 28
A.4 Information to press-in termination and press-in connections . 28
A.4.1 General . 28
A.4.2 Design features . 28
A.4.3 Materials and surface finishes . 29
A.4.4 Press-in terminations with connector contact elements . 29
A.5 Printed board information . 29
A.5.1 General . 29
A.5.2 Plated-through hole . 30
A.5.3 Dimensioning of the hole . 30
A.5.4 Manufacturing of the hole, example with drilling for FR4 . 31
A.5.5 Manufacturing of the hole with materials other than FR4 . 31
A.6 Press-in connection information . 31
A.6.1 General . 31
A.6.2 Press-in connection . 31
A.6.3 Repair of press-in connections . 32
A.6.4 Combination of press-in connections and soldered connections . 33
A.6.5 Bimetallic electrolytic corrosion effects . 33
Bibliography . 34
Figure 1 – Guide for hole ranges in a test board . 12
Figure 2 – Plated-through hole . 13
Figure 3 – Location and example of the transversal microsection for measuring the
copper thickness . 13
Figure 4 – Test arrangement – push-out force. 17
Figure 5 – Transverse section of a press-in connection . 18
Figure 6 – Longitudinal section of a press-in connection . 19
Figure 7 – Test arrangement for contact resistance . 20
Figure 8 – Qualification test schedule . 24
Figure A.1 – Conceptual composition of a four-layer printed circuit board . 30
Figure A.2 – Example of a termination removal tool . 33
Table 1 – Plated-through hole requirements for test printed boards . 12
Table 2 – Vibration, preferred test severities . 18
Table 3 – Qualification test schedule – Test group AP . 22
Table 4 – Qualification test schedule – Test group BP . 22
Table 5 – Qualification test schedule – Test group CP . 23
Table 6 – Application test schedule – Test group DP . 25
Table A.1 – Example for dimensioning the printed circuit board hole . 31
---------------------- Page: 9 ----------------------
SIST EN IEC 60352-5:2020
– 4 – IEC 60352-5:2020 © IEC 2020
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SOLDERLESS CONNECTIONS –
Part 5: Press-in connections – General requirements,
test methods and practical guidance
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC
Publication(s)"). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60352-5 has been prepared by subcommittee 48B: Electrical
connectors, of IEC technical committee 48: Electrical connectors and mechanical structures
for electrical and electronic equipment.
This fifth edition cancels and replaces the fourth edition published in 2012. This edition
constitutes a technical revision.
This edition includes the following significant changes with respect to the previous edition:
a) revising the scope by removing the wording "… telecommunication equipment and in
electronic devices employing similar techniques" and replacing it by "… electrical and
electronic equipment and components" in the first paragraph;
b) adding terms and definitions for 'board', 'hole' and 'metal board' to recognize that press-in
terminations are being used in many non-printed board materials;
---------------------- Page: 10 ----------------------
SIST EN IEC 60352-5:2020
IEC 60352-5:2020 © IEC 2020 – 5 –
c) editorial changes to clarify the difference between the two test schedules for qualification
and application;
d) modification of upper limit of copper thickness of the plated-through-hole to reflect actual
market trends and manufacturing practices;
e) removal of bending test, as this test is very specific for applications of press-in technology
no longer common;
f) adding graphs to document the press-in and push-out force, since this is common testing
practice and provides further insight into mechanical performance of the contact zone;
g) reducing the number of test specimens required, since in previous testing scheme a lot of
test samples were discarded;
h) new wording in 4.5 for cracked and bent terminations;
i) added Figure 7b to show V and A connection locations when the press-in termination does
not protrude through the bottom side of the board.
The text of this International Standard is based on the following documents:
FDIS Report on voting
48B/2810/FDIS 48B/2822/RVD
Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts in the IEC 60352 series, published under the general title Solderless
connections, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
---------------------- Page: 11 ----------------------
SIST EN IEC 60352-5:2020
– 6 – IEC 60352-5:2020 © IEC 2020
INTRODUCTION
This part of IEC 60352 includes requirements and relevant tests (normative) as well as a
practical guidance in Annex A (informative) for press-in connections.
Two test schedules are provided.
a) The qualification test schedule applies to individual press-in connections to demonstrate
the suitability of the press-in zone.
These press-in connections are tested to the specification provided by the manufacturer of
the press-in termination (see 4.6) taking into account the requirements of Clause 4.
The qualification is independent of the application of the press-in zone in a component.
b) The application test schedule applies to press-in connections which are part of a
component and are already qualified to the qualification test schedule.
Test sequences focus on the performance of the press-in connection which is affected by
the implementation in a component.
The requirements and tests apply to all elements involved in the manufacturing of a press-in
connection:
• the press-in termination, which may be part of a component (e.g. a multi-pole connector);
• the board, printed board or MID (moulded interconnect device) - (plated-through holes
dimensions) for which the termination is suitable;
• the tool(s) required to produce the press-in connection.
As the manufacturer of the press-in termination has to provide the main part of the information
needed for qualification, the word "manufacturer" is used throughout this document for
simplicity to indicate the manufacturer of the press-in termination. The manufacturers of the
other items playing a role in the qualification of press-in connections are specified, if needed,
as the board manufacturer or the tool(s) manufacturer.
The practical guidance in Annex A (informative) serves as a guide for the workmanship
required in 4.1. Attention is drawn to the fact that some industries (e.g. automotive, aircraft
and aerospace, nuclear, military) may have specific workmanship standards and/or quality
requirements, which are outside the scope of this document.
IEC Guide 109 advocates the need to minimize the impact of a product on the natural
environment throughout the product life cycle.
---------------------- Page: 12 ----------------------
SIST EN IEC 60352-5:2020
IEC 60352-5:2020 © IEC 2020 – 7 –
SOLDERLESS CONNECTIONS –
Part 5: Press-in connections – General requirements,
test methods and practical guidance
1 Scope
This part of IEC 60352 is applicable to solderless press-in connections for use in electrical
and electronic equipment and components.
The press-in connection consists of a termination having a suitable press-in zone which is
inserted into a hole of a board.
Information on materials and data from industrial experience is included in addition to the test
procedures to provide electrically stable connections under specified environmental conditions.
The object of this document is to determine the suitability of press-in connections under
mechanical, electrical and atmospheric conditions as specified by the manufacturer of the
press-in termination and to provide a means of comparing test results when the tools used to
make the connections are of different designs or manufacture.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their
content constitutes requirements of this document. For dated references, only the edition
cited applies. For undated references, the latest edition of the referenced document (including
any amendments) applies.
IEC 60068-1, Environmental testing – Part 1: General and guidance
IEC 60512-1, Connectors for electrical and electronic equipment – Tests and measurements –
Part 1: Generic specification
IEC 60512-1-1, Connectors for electronic equipment – Tests and measurements – Part 1-1:
General examination – Test 1a: Visual examination
IEC 60512-1-2, Connectors for electronic equipment – Tests and measurements – Part 1-2:
General examination – Test 1b: Examination of dimension and mass
IEC 60512-2-1, Connectors for electronic equipment – Tests and measurements – Part 2-1:
Electrical continuity and contact resistance tests – Test 2a: Contact resistance – Millivolt level
method
IEC 60512-2-5, Connectors for electronic equipment – Tests and measurements – Part 2-5:
Electrical continuity and contact resistance tests – Test 2e: Contact disturbance
IEC 60512-6-4, Connectors for electronic equipment – Tests and measurements – Part 6-4:
Dynamic stress tests – Test 6d: Vibration (sinusoidal)
IEC 60512-11-1, Connectors for electrical and electronic equipment – Tests and
measurements – Part 11-1: Climatic tests – Test 11a – Climatic sequence
---------------------- Page: 13 ----------------------
SIST EN IEC 60352-5:2020
– 8 – IEC 60352-5:2020 © IEC 2020
IEC 60512-11-4, Connectors for electronic equipment – Tests and measurements – Part 11-4:
Climatic tests – Test 11d: Rapid change of temperature
IEC 60512-11-9, Connectors for electronic equipment – Tests and measurements – Part 11-9:
Climatic tests – Test 11i: Dry heat
IEC 611
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.